service MITSUBISHI LANCER EVOLUTION 2007 Service Workshop Manual

ENGINE OVERHAUL -Specifications11B-3
SPECIFICATIONS
SERVICE SPECIFICATIONS
Unit: mm
Items
Standard valueLimited value
Timing belt
Timing belt B
Vibration frequency Hz (during inspection)
Vibration frequency Hz (when re-tensing working belt)
Vibration frequency Hz (when mounting new belt)
Deflection amount (during inspection)
Deflection amount (when re-tensing working belt)
Deflection amount (when mounting new belt)
Auto-tensioner
Rod protrusion length (free length)
Rod protrusion length (when mounting timing belt)
Rod recess amount (when pressed at 98 to 196 N•m)
56 - 92
76 - 92
76 - 92
5-10
5-7
5-7
12.0
3.8 - 4.5
Within 1
-
-
-
Rocker arm, camshaft
Camshaft
Cam height
Intake
Exhaust
35.79
35.4935.29
34.99
Cylinder head, valve
Cylinder head
Lower surface strain
Lower surface grinding limit (in combination with combined cylinder block)
Total height
Valve
Margin
Intake
Exhaust
Total length
Intake
Exhaust
Valve spring
Free height
Squareness
Valve guide
Clearance between valve guide and valve stem
Intake
Exhaust
Total length
Intake
Exhaust
Protrusion amount
Valve seat
Contact width
Valve protrusion amount from spring seat surface
Intake
Exhaust
0.05
-
131.9 - 132.1
1.0
1.5
109.50
109.70
48.3
1.5_or less
0.02 - 0.05
0.05 - 0.09
45.5
50.5
19.2 - 19.8
0.9 - 1.3
49.20
48.400.2
0.2
-
0.5
1.0
109.00
109.20
47.3
4_
0.10
0.15
-
-
-
-
49.70
48.90

ENGINE OVERHAUL -Timing Belt11B-14
REMOVAL SERVICE POINTS
AA"TIMING BELT REMOVAL
1. To ensure that the timing belt is assembled in the same
direction when reused, using chalk, etc., make an arrow
showing the rotation direction on the back surface of
the timing belt.
2. Position the exhaust camshaft sprocket’s timing mark by
approx. one tooth before the No. 1 cylinder compression
top dead centre.
Caution
When removed at the compression top dead centre,
since the exhaust camshaft is at the position pressing
down on the valve, the sprocket could rotate in reverse
due to the force of the valve spring creating a
hazardous situation.
3. Loosen the lock nut for the tensioner pulley, and remove
the timing belt.
AB"OIL PUMP SPROCKET REMOVAL
1. Remove the plug on the left side of the cylinder block.
2. Insert a Phillips driver (shaft diameter 8 mm) to stop the
counter balance shaft left from rotating.
3. Loosen the flange bolt.
4. Remove the oil pump sprocket.
AC"CRANKSHAFT BOLT REMOVAL
1. Fix the flywheel with the special tool.
2. Remove the crankshaft bolt.
AD"CRANKSHAFT SPROCKET REMOVAL
Use the special tool to remove the sprocket if it is stuck
and hard to remove.
Timing marks
Phillips driver
MD998781
MD998778

ENGINE OVERHAUL -Timing Belt11B-15
AE"TIMING BELT B REMOVAL
To ensure that the timing belt is assembled in the same
direction when reused, using chalk, etc., make an arrow
showing the rotation direction on the back surface of the
timing belt.
AF"COUNTER BALANCE SHAFT SPROCKET
REMOVAL
1. Fix the counter balance shaft sprocket with the special
tool.
2. Remove the installation bolt of the counter balance shaft.
AG"CRANKSHAFT SPROCKET B REMOVAL
Use the special tool to remove the sprocket if it is stuck
and hard to remove.
AH"CAMSHAFT SPROCKET BOLT REMOVAL
Hold the hexagon part of the camshaft with a wrench, and
remove the camshaft sprocket bolt.
INSTALLATION SERVICE POINTS
"AACAMSHAFT SPROCKET BOLT INSTALLATION
Hold the hexagon part of the camshaft with a wrench, and
tighten the camshaft sprocket bolt at the specified torque
88±10 N•m.
MD998785
MD998778

ENGINE OVERHAUL -Fuel System11B-27
INSTALLATION SERVICE POINTS
"AAINJECTOR INSTALLATION
1. Apply a small amount of new engine oil on the O-ring.
2. While rotating the injector to the left and right, insert the
O-ring into the delivery pipe while taking care not to
damage it.
Caution
Make sure that the engine oil does not enter the
delivery pipe.
3. Confirm that the injector rotates smoothly. If it does not
rotate smoothly, the O-ring may be biting in. Remove
the injector, check the O-ring for damage, and then insert
it into the delivery pipe. Check the rotation again.
"BAFUEL PRESSURE REGULATOR INSTALLATION
1. Apply a small amount of new engine oil on the O-ring.
2. While rotating the fuel pressure regulator to the left and
right, insert the O-ring into the delivery pipe while taking
care not to damage it.
Caution
Make sure that the engine oil does not enter the
delivery pipe.
3. Confirm that the fuel pressure regulator rotates smoothly.
If it does not rotate smoothly, the O-ring may be biting
in. Remove the fuel pressure regulator, check the O-ring
for damage, and then insert it into the delivery pipe. Check
the rotation again.
"CATHROTTLE BODY GASKET INSTALLATION
Assembly so that the protrusion on the throttle body gasket
is at the position shown in the illustration.
Protrusion

ENGINE OVERHAUL -Secondary Air System and Intake Manifold11B-29
INSTALLATION SERVICE POINTS
"AAINTAKE MANIFOLD STAY INSTALLATION
Check that the intake manifold stay is seated against the
intake manifold and cylinder block boss, and then tighten
at the specified torque 31±3N•m.
"BAMANIFOLD DIFFERENTIAL PRESSURE (MDP)
SENSOR INSTALLATION
Caution
Make sure not to apply impact against the sensor when
installing.
Do not use a sensor that has been dropped.
"CAAIR CONTROL VALVE BRACKET INSTALLATION
1. Temporarily tighten the air control valve bracket and
engine hanger with the bolt for tightening with the intake
manifold.
2. Tighten the bolt 1 shown in the illustration at the specified
torque 23±4N•m.
3. Tighten the bolt 2 shown in the illustration at the specified
torque 36±6N•m.
4. Tighten the bolt 3 shown in the illustration with the engine
hanger at the specified torque 22±4N•m.
"DAAIR PIPE ASSEMBLY INSTALLATION
1. Temporarily tighten air pipe assembly onto the air control
valve.
2. Tighten the bolts 1 and 2 shown in the illustration to
the exhaust manifold at the specified torque 49±5N•m.
3. Tighten the bolt 3 shown in the illustration to the air control
valve at the specified torque 24±3N•m.
4. Tighten the bolt 4 shown in the illustration to the cam
position sensor support at the specified toque 11±1
N•m.
5. Tighten the bolt 5 shown in the illustration to the exhaust
manifold at the specified torque 14±1N•m.
Intake manifold stay
1
23
1
5
23
4

ENGINE OVERHAUL -Exhaust Manifold11B-31
INSTALLATION SERVICE POINTS
"AAEXHAUST MANIFOLD INSTALLATION
1. Lightly tighten the installation nut for the exhaust manifold.
2. Following the tightening order shown in the illustration,
tighten the M8 nuts at the tightening torque 29 N•m.
3. Following the tightening order shown in the illustration,
tighten the M10 nuts at the tightening torque 49 N•m.
4. Following the tightening order shown in the illustration,
tighten the M8 nuts again at the tightening torque 29
N•m.
5. Finally, following the tightening order shown in the
illustration, tighten the M10 nuts at the tightening torque
55±10 N•m, and tighten the M8 nuts at the tightening
torque 33±6N•m.
"BAOIL RETURN PIPE GASKET INSTALLATION
Assembly so that the protrusion of the oil return pipe gasket
on the oil pan side is at the position shown in the illustration.
NOTE
There is no designated assembly direction for the gasket
on the turbocharger side.
"CAAIR OUTLET FITTING GASKET
Assembly so that the protrusion of the air outlet fitting gasket
is at the position shown in the illustration.
7982 13456
Protrusion
Protrusion
AA

ENGINE OVERHAUL -Water Pump and Water Hose11B-33
INSTALLATION SERVICE POINTS
"AAO-RING/WATER INLET PIPE INSTALLATION
Replace the O-ring for the water inlet pipe with a new part,
and apply water on the periphery of the O-ring so that it
can be inserted easily into the water pump and thermostat
housing.
Caution
(1) Never apply grease or oil, such as engine oil, on the
O-ring.
(2) Install the water inlet pipe onto the thermostat
housing, and then fix.
"BAWATER OUTLET FITTING INSTALLATION
Squeeze out form-in-place gasket at a 3 mm width, and apply
at the position shown in the illustration.
Form-in-place gasket
Specified gasket:
Mitsubishi Genuine Part No. MD970389 or
equivalent
"CAENGINE COOLANT TEMPERATURE GAUGE UNIT
INSTALLATION
When reusing the bolts, apply the specified sealant on the
threads.
Sealant
Specified sealant:
3M
TMAAD Part No. 8672 or equivalent
"DAENGINE COOLANT TEMPERATURE SENSOR
INSTALLATION
Apply the specified sealant onto the threads.
Sealant
Specified sealant:
3M
TMAAD Part No. 8731 or equivalent
Caution
Make sure that the tool does not contact the connector
section (resin section).

ENGINE OVERHAUL -Rocker Arm and Camshaft11B-35
REMOVAL SERVICE POINT
AA"LASH ADJUSTER REMOVAL
Caution
When reusing the lash adjuster, always clean and inspect
it before installing. (Refer to the section on checking the
lash adjuster.)
INSTALLATION SERVICE POINTS
"AALASH ADJUSTER INSTALLATION
Caution
When reusing the lash adjuster, always clean and inspect
it before installing. (Refer to the section on checking the
lash adjuster.)
Assembly the lash adjuster onto the rocker arm while taking
care not to spill out diesel oil in it.
"BACAMSHAFT INSTALLATION
1. Apply engine oil on the camshaft journal and cam.
2. Install the camshaft onto the cylinder head.
Caution
Do not mistake the intake and exhaust camshafts.
There is a 4 mm width slit on the back end of the
exhaust side camshaft.
"CABEARING CAP INSTALLATION
1. Set the camshaft’s dowel pin to the approximate top.
2. The bearing caps No. 2 to 5 have the same shape. Check
the identification symbol before installing to prevent
mistaking the cap No., intake side and exhaust side.
Identification symbol
(Stamped on front and on No. 2 to 5 bearing caps)
I : Intake side
E : Exhaust side
Timing belt side
Slit
Exhaust side
Dowel pins
Cap No.
Identification
of IN side and
EX side

ENGINE OVERHAUL -Cylinder Head and Valve11B-41
REMOVAL SERVICE POINTS
AA"CYLINDER HEAD BOLT REMOVAL
Remove the cylinder head bolt using the special tool.
AB"RETAINER LOCK REMOVAL
Compress the valve spring using the special tool, and remove
the retainer lock.
NOTE
Attach a tag indicating the cylinder No. and installation position
onto the parts including the removed valve and springs so
that they can be reassembled later.
INSTALLATION SERVICE POINTS
"AAVALVE STEM SEAL INSTALLATION
1. Install the valve spring seat.
2. Install the valve.
3. Apply a small amount of engine oil on the valve stem
seal.
4. Using the valve stem as a guide, press in the valve guide
using the special tool.
Caution
Improper installation of the valve stem seal can lead
to oil reduction, so always install using the special
tool.
NOTE
Note that the valve stem seals for the intake side and
exhaust side are different.
MB991654
MD998772
MD998735
MB998737
Body colour:
GreyBody colour:
Grayish-green Intake side Exhaust side

ENGINE OVERHAUL -Oil Pump and Oil Pan11B-48
REMOVAL SERVICE POINTS
AA"OIL PAN REMOVAL
1. Remove the oil pan tightening bolts.
2. Tap the special tool between the oil pan and cylinder
block.
3. Tap on the edge of the special tool, slide the tool and
remove the oil pan.
AB"PLUG CAP REMOVAL
Fit the special tool (MD998162) into the notch on the plug
cap as shown in the illustration. Loosen the plug cap while
supporting with the special tool (MD998783).
AC"FLANGE BOLT REMOVAL
1. Remove the plug on the left side of the cylinder block,
and insert a Phillips driver (shaft diameter 8 mm) by 60
mm or more to stop the rotation of the counter balance
shaft left.
2. Loosen the flange bolt.
AD"COUNTER BALANCE SHAFT FRONT BEARING
REMOVAL
Pull out the counter balance shaft front bearing from the
cylinder block using the special tool.
Caution
Always remove the counter balance shaft front bearing
first. Otherwise, the counter balance shaft rear bearing
cannot be removed.MD998727
MD998162
MD998783
Plug
Phillips driver
MD998371Front bearing