check oil NISSAN 300ZX 1984 Z31 Automatic Transmission Workshop Manual

~ ~~ ON-VEHICLE
SERVICE
-Parking Component (Cont'd)-
5. Remove rear extension bolts, then draw out
rear extension with rear mounting.
6. Remove control valve assembly.
7. Inspect and repair parking components Check
component
parts for wear or damage.
-Governor Valve Assembly
1 Drain oil by removing oil pan.
2. Remove rear extension with rear mounting
3. Remove governor valve assembly.
4. Inspect and repair governor valve assembly.
Refer to Governor for inspection
-Inhibitor Switch Adjustment-
Disconnect harness at connector, then remove in-
hibitor switch
Check continuity at "N", "F'" and "R" ranges.
VG30E without turbo
VG30E turbo
VG30E wnhout turbo
0
VG30E turbo
SAT710
With control lever held in "Neutral, turn
manual lever
an equal amount in both direc-
tions to see
if current flow ranges are nearly
the same. (Current normally begins to flow
before manual lever reaches
a angle of 1.5" in
either direction.)
If current flows outside normal range, or if
normal flow range is out of specifications,
properly adjust inhibitor switch.
Adjust inhibitor switch as follows
1 Place the manual valve in Neutral (vertical
2. Remove the screw.
position)
AT-I 2

Vacuum Diaphragm Rod
Adjustment
1. Remove diaphragm from transmission case.
2 Using a depth gauge, measure depth "L". Be
sure vacuum throttle valve is pushed into valve
body
as far as possible.
3 Check "L" depth with chart below and select
proper length rod.
Measured depth "L"
mm (in)
Under 25 55
(1 0059)
25 65
- 26 05
(1 0098
- 1 0256)
26 15
- 26 55
(1 0295 - 1 0453)
26 65
- 27 05
(1 0492 - 1 0650)
Over 27 15
(1 0689)
Vacuum diaphragm
Rod length
mm (in)
29 0
(1 142)
29 5
(1 161)
30
0
(1 181)
30 5
(1 201)
31
0
(1 220)
Vacuum diaphragm
I1
rod
SAT078
Part number
31932- X0103
31932 - XO104
31932- XOlOO
31932- X0102
31932. XOlOl
Downshift Solenoid
1. Remove downshift solenoid and O-ring.
Catch
oil dropping out of the hole.
SAT516
2 Check to verify that downshift solenoid is
operatmg properly. If faulty, replace it with a
new one
SAT517
AT-I4

REMOVAL AND INSTALLATION
Removal
a Remove bolts securing torque converter to
drive plate.
a. Remove those bolts turning crank shaft.
b. Before removing torque converter, inscribe
matching marks on
two parts so that they may
be replaced in their original positions during
assembly.
a Plug up openings such as oil charging pipe, etc.
CAUTl ON :
Take care when dismounting transmission not to
strike any adjacent
parts.
Installation
0
a
a.
b.
a
Drive plate runout
Maximum allowable runout:
0.5 mm (0 020 in)
n
SAT718
If this runout is out of allowance, replace drive
plate and ring gear
When connecting torque converter to trans-
mission, measure distance "A" to be certain
that they are correctly assembled.
Distance "A":
More than
35 mm (1.38 in)
Install converter to drive plate
Align matching marks painted across both parts
during disassembly.
Before installing torque converter securing
bolts, apply locking sealer to threads
of bolts.
After converter is installed, rotate crankshaft
several turns and check to be sure that trans-
mission rotates freely without binding
AT-I 8

REPAIR FOR COMPONENT PARTS
Oil Pump (Cont'd)
ASSEMBLY
1. Install lock-up control valve and spring into oil
pump cover, then tap new retaining pin.
2 Mount pump housing in Tool and suitable
spacer. Set up pump housing with inner and
outer pump gears on
it and install pump cover
to pump housing Temporarily assemble
oil
pump.
sar-0
3 Set the cover to within the run-out of the
specified total indicator reading.
Total indicator reading:
Less than 0.07 mm (0 0028 in)
SAT541 &25580001
4 Tighten pump securing bolts to the specified
torque Recheck run-out
Drum Support
DISASSEMBLY
1 Remove drum support and gasket from O.D.
case.
SATW
2. Stake off retaining pin using a punch [outer
dia.
1.5 to 1.8 mm (0.059 to 0.071 in)], then
remove
O.D. cancel valve and spring
Don't stake it off from contacting face side
7 Retaining pin
00
AT-30

REPAIR FOR COMPONENT PARTS
Drum Support (Cont'd)
5 Mount 0 D. case, drum support and gasket in
oil pump assembly Temporarily assemble
drum support.
Ensure O.D. case is inserted properly into oil pump
assembly.
0 0 case
I pump cafe 11 An
011 pump centering
SAT547
6. Insert an approx. 110 mm (4.33 in) bar into
bore in oil pump
at shaft location and install
intermediate shaft onto
it.
intermediate shaft
011 pump centering
tool lST25580001)
Suitablebar [llOmm
SAT599 20 mm IO 79 dl
This operation can also be performed by using
Tool
(533909)
7 Set the drum support within the run-out of the
specified total indicator reading
Total indicator reading:
Less than 0 05 mm (0.0020 in)
8 Tighten drum support securing bolts to the
specified torque.
Recheck run-out.
AT-33

REPAIR FOR COMPONENT PARTS
Control Valve Body (Cont'd)
I
@ Second lock valve
VALVE BODY SPRING CHART
055(00217) 555(021851 16 33 5 (1 319) 21 0 (0 827) 5 88 (0 60,1.32)
Free length
check
valve VG30E turbo 1 0 (0 0391 6 5 (0 256) 13 24 9 (0 980)
Outer
19 0 (0 748) 27 95 (2 85,6 28)
Numbers stamped on valve springs listed in table
~ below are the Same as those in the figure on the
previous page.
Orifice check valve
Servo orifice check
valve
3rd - 4th VG30E
@ shift
VG30E turbo
I nsta I led Outer coil
mm (in)
Wire dia No of Free length
Valve spring dia active
coil mm (in) Length mm (in)
mm (in) N (kg. Ib)
023 (00091) 50 (0 197) 12
0 8 (0 031) 6 6 (0260) 12 6
0 75 (0 0295) 6 1 (0 240) 13 6
-
Solenoid downshift 10 55 (0 0217) 15 55 (0 2185) I 12 @ valve
155(0610)
22 0 (0 866) 12 5 (0 492) 5 88 (0 60,l 32) I
11 5(04531 OlO(OOl.002)
30 3 (1 193)
I VG30E 1 09 (0035) 1 65(0256) I 14 relief
24 586
13 1 (0 516) (2 507, 528)
26 8 (1 055) 19 0 (0 748) 21 48 (2 19,4 83)
3rd - 2nd
valve
@ timing
VG30E 0 7 (0 028) 5 9 (0 232) 12 5 227(0894) 14.5(0571) 11 08(1.13,249)
VG30E turbo 0 9 (0 035) 7 4 (0 291) 9 207(0815) 14.5(0571) l648(1 68,370)
268(1055) I131 (0516) I 2138(218.481)
AT-35

REPAIR FOR COMPONENT PARTS
Control Valve Body (Cont'd)
DISASSEMBLY
1. Remove oil Strainer.
SAT564
2. Separate lower body, separator plate and upper
body.
Be careful not to scatter or lose orifice check valve,
servo orifice check valve, or throttle relief check
valve (ball)
and related spring.
AT168
INSPECTION
A newly manufactured valve body represents
precision manufactured valves assembled with close
tolerances into precision bores of the valve body
If inspection reveals excessive clearances, 0.03 mm
(0 0012 in) or more, between the valves and the
valve body bores, replace the entire valve body
rather than attempt rework
If one or more valves are sticking from varnish
deposits or burns resulting from deteriorated oil or
overheating, you may be able to clean the valves
and valve bodies. Always use crocus cloth, which is
a very fine type of cutting material Never use
emery cloth,
as it is too coarse and can scratch the
valves or valve bores Scratches can lead to future
deposits of varnish or foreign matter
During cleaning, do not remove the sharp edges of
the valve When
edges are rounded or scratched,
entry
is provided for dirt or foreign matter to work
into the sides
of the valves and hinder valve move-
ment
The valves may be cleaned using alcohol or lacquer
thinner The valve bodies can be dip cleaned with
a good carburetor cleaner or lacquer thinner. Do
not leave valve bodies submerged in carburetor
cleaner longer than five minutes Rinse parts
thoroughly
and dry
Lubricate
all parts in clean AT F before reassem-
bly
1 Check valves for signs of burning Replace if
2 Check oil strainer for general condition.
beyond clean-up
Replace
if necessary
SATMS
AT-36

REPAIR FOR COMPONENT PARTS
Control Valve Body (Cont’d)
3 Check separator plate for scratches or damage
Replace if necessary Scratches or score marks
can cause oil to by-pass correct oil passages
and result in system malfunction
SAT046
4. Check oil passages in upper and lower valve
bodies for varnish deposits, scratches or other
damage that would impair valve movement.
Check threaded holes and related bolts and
screws for stripped threads, replace
as needed
Test valve springs for weakened load condition
Refer to Valve Body Spring Chart for spring
specifications.
5
ASSEMBLY
1 Install orifice check valves, valve springs, throt-
tle relief valve spring and steel ball in valve
body
Lower valve body
Orifice check Valve-P for 2nd-3rd rhifl .. reiea* (VG30E turbo (I a xbo only)
-oroftee check valve
Throttle relief valve,
Orifice chkk valveJ (direct clutch applies) SAT743
Upper valve body
A
Onfice check valve--@ (Front clutch applies) h
2 Assemble separator plate and upper valve body
on lower valve body, then tighten bolts.
ReaGer bolt
When installing these bolts, first be sure to install
the two reamer bolts to their original positions.
3. Install oil strainer.
AT-37

REPAIR FOR COMPONENT PARTS
Direct Clutch & Front Clutch (Cont'd)
DISASSEMBLY
Compress clutch springs and remove snap ring
from spring retainer using
Tool.
e For easy removal of piston from drum, mount
clutch on drum support. Use an air gun with
a
tapered rubber up to carefully apply air pres-
sure to loosen piston from drum
INSPECTION AND ASSEMBLY
1 Check clutch drive plate facing for wear or
damage.
Standard thickness:
Wear limit:
2 Check for wear on snapring, weak or broken
coil springs, and warped spring retainer.
3. Check the operation of check ball in piston
using compressed air.
1.50 - 1.65 mrn (0.0591 - 0.0650 in)
1.4 mm (0.055 in)
LAW IS blocked here
SAT553
4 Lubricate clutch drum hub and seals, and
install inner
seal and piston seal as illustrated
Be careful not to stretch seals during instal-
lation
SAT031
5. Assemble piston, being careful not to allow seal
to kink or become damaged during installation.
After installing, turn piston
by hand to ensure
that there
is no binding.
/ .----icJ SAT032
AT-40

Prmary valve ~~
Wire
dia
(In)
(0 5 - 0 7 kg-m,
Installed Outer mil
dia
mm (in)
No of Free length
active coil mm (in) Length
mm (in) N (kg, Ib)
- \01i distributor
VG30E Primary
governor VG30E turbo
SAT560
0 65 (0 0256) 8 95 (0 3524)
0 45 (0 0177) 8 75 (0 3445)
4 4
50 10 5 (0 413)
21 8 (0 858)
7 5 (0 295)
7
5 (0 295)
2 109 (0 215,O 474)
2 109 (0 215,O 474)
mor
VG30E Secondary
0 Check valves for burning or scratches. Inspect
springs for weakness or burning Replace parts
as necessary
Do not interchange components of primary and
secondary governor valves
GOVERNOR VALVE SPRING CHART
0 70 (0 0276) 9 20 (0 3622) 5 5 19 8 (0 780) 10 5 (0 4131 6 9 (0 7,l 5)
rt:A As instaled
Wvernor
SAT039
VG30E turbo 0 70 (0 0276) 9 20 (0 3622) 5 5 19 8 (0 780) 10 5 (0 413) 6 9 (0 7.1 5)
Valve spring
AT-46