warning NISSAN 300ZX 1984 Z31 Body Owner's Guide

BODY END AND DOOR
Theft Warning System (Cont'd)
J
J J
I I J
X X 0 0
J I I-
X X
x
X
X
X -
X X
X X X X
X 0 X X
X 0 0
I I I
- 0
c 8
- 0 0
- E 0 .. .
0 0 5
0 a z
BF-43

BODY END AND DOOR
Theft Warning System (Cont'd)
I
I
JI -I I J
I I= X I
XI x I X I I
X X X
0 X 0
I I
I I I
- V 0
0 c
0 Q 0 0 0 I3 z z z
=r
X
I?
O?
Jr
X
X
X
X
0
I
BF-44

BODYENDANDDOOR
Theft Warning System (Cont'd)
X
XIX X X
L X
0
L
x -
I'
0 0 0
+f-
x
0 0 0
X X x
X X
0 0 0 0
I I I I
I
4, a: 2 4
?
5 Q
BF-45

BODY END AND DOOR
Theft Warning System (Cont'd)
@ terminal inspection 'Z) twminal inspeainn
Connect tester between @and subcontrol AMP @ temlnal
I I
Check continuity
@ terminal inspeenon
Connect @and @with jumper cable
u
Doer indicator lamp come on7
(Only If connected)
1 YES I ,
&
@ terminal inspection
Doer starter motor turn?
(Only in above case)
I
&
Connect Oand @I wnh jumper cable
v I T
Does horn sound7
(Only if connected)
6) terminal inspection
1 YES
I
&
Connect@and @with iumpr cable
i__T__li
I
Doer indicator lamp come on7 lOnly if connected)
I I
0 (@ terminal inspection
Connect test lamp (Less than 1W) between @ and @
4
Unlockany key cylinder with key and hold key bervveen
full stroke and neutral
IDriverIanst door or back door)
NO
(Any of
them)
I
Does test lamp come on7 (Only m abow care)
(Both cases)
BF-47

BODY END AND DOOR
Theft Warning System (Cont'd)
@ terminal 8wection 0 terminal inspection
Connect tester between0and @
@ terminal
Dmgrees with
Dmgreer with trouble
Check voltage Ignition switch OFF
Ignition switch ACC or ON H
Agrees wnh trouble diagnosis chart
@ termma1 inspection
Connect tester betwen @and@
Disagrees with
trouble
diagnosis chart
Cheek voltage
Unlock, Neutral L
Lock
iapprox 0 1 second at the < moment of key cylinder operation1 H
~greer wnh trouble
I diagnosis chart I
Connect tester between aand @
Gl terminal 0
Disagrees with
trouble
Door IS closed-Disarmed
phase 01 iesn phase H Door IS opened, key
cylinder
IS drawn out, or
Agrees with trouble
Connect tester between @ and @
@ terminal
I
Voltage H
I
&
I
&
& di~gnoris chart I
BF-48

SEAT BELT
Refer to MA section for installation of seat belts.
GLL model has been equipped with seat belts with tension reducer This unit reduces the force required
to pull out seat belt while in use, and lessens pressure on the shoulder and hips for greater comfort
TENSION REDUCER WIRING DIAGRAM
IGNITION SWITCH I ON or ST
TENSION REDUCER-Assist
FUSE BLOCK
@
U
SEAT BELT SWITCH-Assist Iinrjde retractor1 (Main harness1
TENSION REDUCER-Driver (Inside retractor)
SEAT BELT SWITCH-Drwer IM~I~ IPower
harness1 To rime control unit (Seat belt warning lamp1
To engine room harness (Ground)
__ seat cushion ground
TENSION REDUCE OPERATION
SBF439B
Fully Seat belt stroke Fully retraned pulled out SBFMOE

WINDSHIELD AND WINDOWS
Windshield
REMOVAL
After removing moldings. remove
glass
I Cutting sealant /I
CAUTION Be careful not to scratch glass when
removing
INSTAL LATl ON
Use genuine Nissan Sealant kit or equivalent Follow instructions furnished
with it
After installation, the vehicle should remain stationary for about 24 hours
Do not use sealant which is more than 12 months past its production date
Do not leave cartridge unattended with its cap open
Keep Primers and sealant in a cool, dry place Ideally, sealant should be stored
in a refrigerator
WARNING
Keep heat or open flames away as Clean banding surface thoroughly -1 Primers are flammable
I Glass side
Body stde
,m SEF4136
i-- Bod; side Glass'side
-- 4 nstall molding fastener When inrtalling it. heat body panel and
fastener to approx 30 to 40'C (86 to
Side Molding Fastener
SBF414B
I - .
Apply primer E
S E F038 B
Allow Primers to dry for 10 to 15
minutes before proceeding to the next
CAUTION
step
T Install dam rubber
8 mrn 10 31 in) 5EF415B
I
Apply primer A
&&$P& 11111
SEFO39B I
CAUTION.
Do not apply Primer A to windshield
I opening flanges
@
BF-63