wheel bolt torque NISSAN 300ZX 1984 Z31 Maintenance Workshop Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 1984, Model line: 300ZX, Model: NISSAN 300ZX 1984 Z31Pages: 38, PDF Size: 1.19 MB
Page 21 of 38
CHASSIS AND BODY MAINTENANCE
Checking Front Axle and Front Suspension Parts
(1) Shake each front wheel
Check axle and suspension parts for looseness,
wear or damage.
SMA525A
(2) Retighten all nuts and bolts to the specified
torque
Refer to section
FA for tightening torque
SMA614
SMA615
(3) Check axle and suspension parts for wear,
cracks or damage.
0 Check strut (Shock absorber) for oil leakage
or damage
SMA113
Check suspension ball joint for grease leakage
and ball joint dust cover for damage
SMA7ZJA
MA-21
LL
Page 22 of 38
CHASSIS AND BODY MAINTENANCE
Checking Front Wheel
Bearing Grease
0 Check that wheel bearings operate smoothly,
as well
as axial end play and grease leakage
Smooth turn
0 mm (0 ,"I
SMA724A v
If necessary, adjust wheel bearing preload
to section
FA.
Refer
Checking Rear Axle and
Rear Suspension Parts
0
(1) Shake each rear wheel
Check axle and suspenslon parts for looseness,
wear or damage
SMA525A
(2) Retighten all nuts and bolts to the specified
torque.
Refer
to sectlon RA for tightening torque.
MA-22
.
Page 36 of 38
SERVICE DATA AND SPECIFICATIONS (S.D.S.)
Used belt deflection
Limit
Adlusted deflecraon
Engine Maintenance
INSPECTION AND ADJUSTMENT
st deflec. TIon Of
new belt Pedal free Play "A"
Alternator
1 -3 IO M -0 121
Arr conditioner I 16 I 9-11 I 7-9 compressor (0631 1035 0431 (028-0351
ADDlted pushtng force I 98 N 110 kg, 22 Ibl
21
10831 Power steering 011 pump
Oil capacity
13.16 10-13
1051 .0631 (039-0511 ~~
unlt P IUS qt. Imp qtl
Wheel alignment IUnladenI
Camber
degree
Caster degree
-35' to 55'
5*50.7"30
Coolant capacity Unlt &? IUS qt. Imp qtl
Wlth 041 falter
Wtthout
001 filter
VG30E & VG30ET
4
0 (4-1 /4, 3-1/21
3 3 13-1/2.
2 7/81
Spark plug
VG30E
I VG30E I VO3OET
105 111-1/8, 91/41
Front wheel turning angle Toe-out turns
Inner wheelIOufer wheel
degree
Plug uaD I 10- 1 1 mm 10039-OW3 in1
22"30'/20'
altitude I 20*2'/650t50 I 20t2'/650f50
standard iype
Hot type
Cola woe
condmon
VG30ET I 20 f 2"/700 f 50 I 20 + 2'/650 t 50
BCPR6ES.11 BCPR6E-11
BCPRSES.11 BCPRSE-11
BCPR7ES.11 BCPR7E-11
TIGHTENING TORQUE
U"lt Nm kg-m ft-lb
Full turns Inner wheel degree
Outer wheel degree
Or1 pan drain plug 29-39 30-40 22-29
Spark plug 20-29 20-30 14-22
Fuel hme clamps 10-15 010-015 07-11
35" .39"
27" .31'
-Chassis and Body Maintenance-
INSPECTION AND ADJUSTMENT
Clutch
Unlt mm 11nI
Pedal height "H" I 195 - 205 I7 68.8 071
Front axle and front suspension
Wheel bearmg preload
IAr measured at wheel hub bolt1 6 86.14 61
With used parts N Ikg, Ibl 1 1 67.7 75 IO 17-079.037- 1741
Kingpin mclination degree I 12'15'- 13'45
degree I 6'- 16
Out 3 (0 0361 - In 3 (0 0361 Side lip IReference datal mm/m lin/ftl
37 5 I1 476) Standard side rod length "A" mm bnl
* On power steering models, wheel turning force la1 circumference
afsteeringwheellof98-147NI10-15kg.22-33lblwith
engtne at idle
Rear axle and rear suspension
Camber degree I -1-55' fa -25
mm (4") I -2 to 2 1-0 08 to 0 081 Toe-,"