fuse NISSAN NOTE 2016 Service Owner's Manual
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 523 of 3641
![NISSAN NOTE 2016 Service Owners Manual C1111 ABS MOTOR, MOTOR RELAY SYSTEM
BRC-75
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
2.PERFORM SELF-DIAGNOSIS
With CONSULT
1. Turn the ignition switch OFF → ON, and NISSAN NOTE 2016 Service Owners Manual C1111 ABS MOTOR, MOTOR RELAY SYSTEM
BRC-75
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
2.PERFORM SELF-DIAGNOSIS
With CONSULT
1. Turn the ignition switch OFF → ON, and](/img/5/57363/w960_57363-522.png)
C1111 ABS MOTOR, MOTOR RELAY SYSTEM
BRC-75
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
2.PERFORM SELF-DIAGNOSIS
With CONSULT
1. Turn the ignition switch OFF → ON, and wait 30 seconds.
2. Start the engine.
3. Drive the vehicle at approx. 50 km/h ( 31 MPH) or more for approx. 2 minutes.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
4. Stop the vehicle.
5. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
6. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
7. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C 1111” detected?
YES >> GO TO 3.
NO >> Inspection End.
3.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electr ic unit (control unit) power supply and ground circuits. Refer to BRC-121,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair / replace harness, connector, or fuse, and GO TO 4.
4.ERASE SELF-DIAGNOSIS RESULT (1)
With CONSULT
1. Start the engine.
2. Drive the vehicle at approx. 50 km/h ( 31 MPH) or more for approx. 2 minutes.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
3. Stop the vehicle.
4. Erase “Self Diagnostic Result” of “ABS”.
5. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
>> Inspection End.
5.CHECK TERMINAL
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Instal-
lation".
NO >> Repair / replace harness or connector, and GO TO 6.
6.ERASE SELF-DIAGNOSIS RESULT (2)
With CONSULT
1. Start the engine.
2. Drive the vehicle at approx. 50 km/h ( 31 MPH) or more for approx. 2 minutes.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
3. Stop the vehicle.
4. Erase “Self Diagnostic Result” of “ABS”.
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 525 of 3641
![NISSAN NOTE 2016 Service Owners Manual C1115 WHEEL SENSORBRC-77
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1115 WHEEL SENSOR
DTC DescriptionINFOID:0000000012430864
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Co NISSAN NOTE 2016 Service Owners Manual C1115 WHEEL SENSORBRC-77
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1115 WHEEL SENSOR
DTC DescriptionINFOID:0000000012430864
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Co](/img/5/57363/w960_57363-524.png)
C1115 WHEEL SENSORBRC-77
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
C1115 WHEEL SENSOR
DTC DescriptionINFOID:0000000012430864
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Start the engine.
2. Drive the vehicle at approx. 50 km/h ( 31 MPH) or more for approx. 2 minutes.
3. Stop the vehicle.
4. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
5. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
6. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C 111 5” detected?
YES-1 >> “C1115” is displayed as “CRNT”: Proceed to BRC-77, "Diagnosis Procedure".
YES-2 >> “C1115” is displayed as “PAST”: Inspec tion End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430865
CAUTION:
Never check between wheel sensor harness connector terminals.
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C 111 5 ABS SENSOR [ABNORMAL
SIGNAL]
(Wheel sensor [abnormal sig-
nal]) When difference in wheel speed between any wheel and others is detected when the ve-
hicle is driven, because of installation of other tires than specified.
PAST DTC
CRNT DTC
• Harness or connector
• Wheel sensor
• Sensor rotor
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery • Harness or connector
• Wheel sensor
• Sensor rotor
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
• Tire size
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 526 of 3641
![NISSAN NOTE 2016 Service Owners Manual BRC-78
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1115 WHEEL SENSOR
1.CHECK TIRE
Check the tire air pressure, wear and size. Refer to WT-54, "
Tire Air Pressure".
Is the inspection result normal?
YES >> NISSAN NOTE 2016 Service Owners Manual BRC-78
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1115 WHEEL SENSOR
1.CHECK TIRE
Check the tire air pressure, wear and size. Refer to WT-54, "
Tire Air Pressure".
Is the inspection result normal?
YES >>](/img/5/57363/w960_57363-525.png)
BRC-78
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1115 WHEEL SENSOR
1.CHECK TIRE
Check the tire air pressure, wear and size. Refer to WT-54, "
Tire Air Pressure".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Adjust air pressure or replace tire and GO TO 2.
2.CHECK DATA MONITOR (1)
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine.
4. Select “DATA MONITOR” of “ABS”, check “FR LH SENSOR”, “FR RH SENSOR”, “RR LH SENSOR” and
“RR RH SENSOR”.
NOTE:
Set the “DATA MONITOR” recording speed to “10 msec”.
5. Read the values (wheel speed) of both the norma l wheel sensors and malfunctioning wheel sensor.
NOTE:
Vehicle must be driven after repair or replacement to erase the previous DTCs.
Note the difference at 50 km/h (31 MPH) between the wheel speed detected by the malfunctioning wheel sen-
sor and the maximum/minimum wheel speed detected by t he normal wheel sensors, is the difference within
5%, respectively?
YES >> GO TO 3.
NO >> GO TO 4.
3.PERFORM SELF-DIAGNOSIS (1)
With CONSULT
1. Stop the vehicle.
2. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
3. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
4. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1115” detected?
YES >> GO TO 4.
NO >> Inspection End.
4.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electric unit (contro l unit) power supply and ground circuits. Refer to BRC-121,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair / replace harness, connector, fuse, or fusible link.
5.CHECK WHEEL SENSOR AND SENSOR ROTOR
1. Turn the ignition switch OFF.
2. Disconnect wheel sensor harness connector.
3. Remove dust and foreign matter adhered to the wheel sensor and sensor rotor with a vacuum dust collec- tor through the wheel sensor mounting hole.
CAUTION:
Install wheel sensor with no backlash and float, and tighten the mounting bolt to the specified
torque.
• Front: Refer to BRC-140, "
FRONT WHEEL SENSOR : Exploded View".
•Rear: Refer to BRC-141, "
REAR WHEEL SENSOR : Exploded View".
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 532 of 3641
![NISSAN NOTE 2016 Service Owners Manual BRC-84
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1116 STOP LAMP SWITCH
C1116 STOP LAMP SWITCH
DTC DescriptionINFOID:0000000012430866
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CR NISSAN NOTE 2016 Service Owners Manual BRC-84
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1116 STOP LAMP SWITCH
C1116 STOP LAMP SWITCH
DTC DescriptionINFOID:0000000012430866
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CR](/img/5/57363/w960_57363-531.png)
BRC-84
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1116 STOP LAMP SWITCH
C1116 STOP LAMP SWITCH
DTC DescriptionINFOID:0000000012430866
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF, and wait 10 seconds or more.
2. Start the engine.
NOTE:
Stop the vehicle.
3. Wait 1 minute or more. NOTE:
Never depress brake pedal.
4. Depress brake pedal by 100 mm (3.94 in) or more, and ma intain at that position for a minimum of 1 minute
or more.
5. Release brake pedal, and wait 1 minute or more.
6. Repeat step 4 to 5 ten or more times.
7. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
8. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
9. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1116” detected?
YES-1 >> “C1116” is displayed as “CRNT”: Proceed to BRC-85, "Diagnosis Procedure".
YES-2 >> “C1116” is displayed as “PAST”: Inspection End (Erase “Self Diagnos tic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C 111 6 STOP LAMP SW
(Stop lamp switch) • When stop lamp switch signal is not input when brake pedal operates.
• When stop lamp switch signal is input when brake pedal is not operated.
PAST DTC
CRNT DTC
• Harness or connector
• Stop lamp switch signal circuit • Harness or connector
• Stop lamp switch
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 534 of 3641
![NISSAN NOTE 2016 Service Owners Manual BRC-86
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1116 STOP LAMP SWITCH
4. Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with
harness connector.
5. NISSAN NOTE 2016 Service Owners Manual BRC-86
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1116 STOP LAMP SWITCH
4. Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with
harness connector.
5.](/img/5/57363/w960_57363-533.png)
BRC-86
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1116 STOP LAMP SWITCH
4. Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with
harness connector.
5. Disconnect stop lamp switch harness connector.
6. Check the stop lamp switch harness connector for disconnection or looseness.
7. Check the stop lamp switch pin terminals for damage or loose connection with harness connector.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair / replace harness, connector, or terminal, and GO TO 6.
6.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electric unit (contro l unit) power supply and ground circuits. Refer to BRC-121,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 7.
NO >> Repair / replace harness, connector, fuse, or fusible link.
7.CHECK DATA MONITOR (2)
With CONSULT
1. Erase “Self Diagnostic Result” of “ABS”
2. Turn the ignition switch OFF → ON → OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF or ON.
3. Start the engine. NOTE:
Stop the vehicle.
4. Select “DATA MONITOR” of “ABS”, check “STOP LA MP SW”. Check that data monitor displays “On” or
“Off” when brake pedal is depressed or released. Refer to BRC-36, "
Reference Value".
Is the inspection result normal?
YES >> Inspection End.
NO >> GO TO 8.
8.CHECK STOP LAMP SWITCH CIRCUIT (1)
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Check the voltage between ABS actuator and elec tric unit (control unit) harness connector and ground.
4. Turn the ignition switch ON.
5. Check the voltage between ABS actuator and elec tric unit (control unit) harness connector and ground.
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Instal-
lation".
NO >> Repair / replace harness or connector, and GO TO 9.
9.CHECK STOP LAMP SWITCH CIRCUIT (2)
1. Turn the ignition switch OFF.
ABS actuator and electric unit (control unit) — Condition Vo l ta g e
(Approx.)
Connector Terminal
E33 12Ground Brake pedal depressed
10 − 16 V
Brake pedal not depressed 0 V
ABS actuator and electric unit (control unit)
— Condition Vol tag e
(Approx.)
Connector Terminal
E33 12Ground Brake pedal depressed
10 − 16 V
Brake pedal not depressed 0 V
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 536 of 3641
![NISSAN NOTE 2016 Service Owners Manual BRC-88
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1120, C1122, C1124, C112
6 ABS IN VALVE SYSTEM
C1120, C1122, C1124, C1126 ABS IN VALVE SYSTEM
DTC DescriptionINFOID:0000000012430869
DTC DETECTION LOGIC
NISSAN NOTE 2016 Service Owners Manual BRC-88
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1120, C1122, C1124, C112
6 ABS IN VALVE SYSTEM
C1120, C1122, C1124, C1126 ABS IN VALVE SYSTEM
DTC DescriptionINFOID:0000000012430869
DTC DETECTION LOGIC](/img/5/57363/w960_57363-535.png)
BRC-88
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1120, C1122, C1124, C112
6 ABS IN VALVE SYSTEM
C1120, C1122, C1124, C1126 ABS IN VALVE SYSTEM
DTC DescriptionINFOID:0000000012430869
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1120”, “C1122”, “C1124” or “C1126” detected?
YES-1 >> “C1120”, “C1122”, “C1124” or “C1126” is displayed as “CRNT”: Proceed to BRC-88, "Diagnosis
Procedure".
YES-2 >> “C1120”, “C1122”, “C1124” or “C1126” is disp layed as “PAST”: Inspection End (Erase “Self Diag-
nostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430870
1.CHECK CONNECTOR
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1120 FR LH IN ABS SOL
(Front LH ABS IN solenoid valve) When a malfunction is detected in front LH ABS IN valve.
C1122 FR RH IN ABS SOL
(Front RH ABS IN solenoid valve) When a malfunction is detected in front RH ABS IN valve.
C1124 RR LH IN ABS SOL
(Rear LH ABS IN solenoid valve) When a malfunction is detected in rear LH ABS IN valve.
C1126 RR RH IN ABS SOL
(Rear RH ABS IN so
lenoid valve)When a malfunction is detected in rear RH ABS IN valve.
PAST DTC
CRNT DTC
• Harness or connector
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery • Harness or connector
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 537 of 3641
![NISSAN NOTE 2016 Service Owners Manual C1120, C1122, C1124, C1126 ABS IN VALVE SYSTEM
BRC-89
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric NISSAN NOTE 2016 Service Owners Manual C1120, C1122, C1124, C1126 ABS IN VALVE SYSTEM
BRC-89
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric](/img/5/57363/w960_57363-536.png)
C1120, C1122, C1124, C1126 ABS IN VALVE SYSTEM
BRC-89
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (contro l unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 2.
2.PERFORM SELF-DIAGNOSIS
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1120”, “C1122”, “C1124” or “C1126” detected?
YES >> GO TO 3.
NO >> Inspection End.
3.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electr ic unit (control unit) power supply and ground circuits. Refer to BRC-121,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair / replace harness, connector, fuse, or fusible link.
4.CHECK TERMINAL
Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-
ness connector.
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Instal-
lation".
NO >> Repair / replace harness, connector, or terminal.
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 538 of 3641
![NISSAN NOTE 2016 Service Owners Manual BRC-90
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1121, C1123, C
1125, C1127 ABS OUT VALVE SYSTEM
C1121, C1123, C1125, C1127 ABS OUT VALVE SYSTEM
DTC DescriptionINFOID:0000000012430871
DTC DETECTION LOGI NISSAN NOTE 2016 Service Owners Manual BRC-90
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1121, C1123, C
1125, C1127 ABS OUT VALVE SYSTEM
C1121, C1123, C1125, C1127 ABS OUT VALVE SYSTEM
DTC DescriptionINFOID:0000000012430871
DTC DETECTION LOGI](/img/5/57363/w960_57363-537.png)
BRC-90
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1121, C1123, C
1125, C1127 ABS OUT VALVE SYSTEM
C1121, C1123, C1125, C1127 ABS OUT VALVE SYSTEM
DTC DescriptionINFOID:0000000012430871
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1121”, “C1123”, “C1125” or “C1127” detected?
YES-1 >> “C1121”, “C1123”, “C1125” or “C1127” is displayed as “CRNT”: Proceed to BRC-90, "Diagnosis
Procedure".
YES-2 >> “C1121”, “C1123”, “C1125” or “C1127” is disp layed as “PAST”: Inspection End (Erase “Self Diag-
nostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430872
1.CHECK CONNECTOR
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1121 FR LH OUT ABS SOL
(Front LH ABS OUT solenoid valve) When a malfunction
is detected in front LH ABS OUT valve.
C1123 FR RH OUT ABS SOL
(Front RH ABS OUT solenoid valve) When a malfunction is detected in front RH ABS OUT valve.
C1125 RR LH OUT ABS SOL
(Rear LH ABS OUT solenoid valve) When a malfunction is detected in rear LH ABS OUT valve.
C1127 RR RH OUT ABS SOL
(Rear RH ABS OUT so
lenoid valve)When a malfunction
is detected in rear RH ABS OUT valve.
PAST DTC CRNT DTC
• Harness or connector
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery • Harness or connector
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 539 of 3641
![NISSAN NOTE 2016 Service Owners Manual C1121, C1123, C1125, C1127 ABS OUT VALVE SYSTEM
BRC-91
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric NISSAN NOTE 2016 Service Owners Manual C1121, C1123, C1125, C1127 ABS OUT VALVE SYSTEM
BRC-91
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric](/img/5/57363/w960_57363-538.png)
C1121, C1123, C1125, C1127 ABS OUT VALVE SYSTEM
BRC-91
< DTC/CIRCUIT DIAGNOSIS > [VDC/TCS/ABS]
C
D
E
G H
I
J
K L
M A
B
BRC
N
O P
1. Turn the ignition switch OFF.
2. Check the ABS actuator and electric unit (contro l unit) harness connector for disconnection or looseness.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair / replace harness or connector, securely lock the connector, and GO TO 2.
2.PERFORM SELF-DIAGNOSIS
1. Turn the ignition switch OFF. NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine. NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1121”, “C1123”, “C1125” or “C1127” detected?
YES >> GO TO 3.
NO >> Inspection End.
3.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) POWER SUPPLY AND GROUND CIR-
CUIT
Check the ABS actuator and electr ic unit (control unit) power supply and ground circuits. Refer to BRC-121,
"Diagnosis Procedure".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair / replace harness, connector, fuse, or fusible link.
4.CHECK TERMINAL
Check the ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with har-
ness connector.
Is the inspection result normal?
YES >> Replace the ABS actuator and electric unit (control unit). Refer to BRC-144, "Removal and Instal-
lation".
NO >> Repair / replace harness, connector, or terminal.
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 540 of 3641
![NISSAN NOTE 2016 Service Owners Manual BRC-92
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1130 ENGINE SIGNAL
C1130 ENGINE SIGNAL
DTC DescriptionINFOID:0000000012430873
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If NISSAN NOTE 2016 Service Owners Manual BRC-92
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1130 ENGINE SIGNAL
C1130 ENGINE SIGNAL
DTC DescriptionINFOID:0000000012430873
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If](/img/5/57363/w960_57363-539.png)
BRC-92
< DTC/CIRCUIT DIAGNOSIS >[VDC/TCS/ABS]
C1130 ENGINE SIGNAL
C1130 ENGINE SIGNAL
DTC DescriptionINFOID:0000000012430873
DTC DETECTION LOGIC
POSSIBLE CAUSE
NOTE:
Confirm if DTC is PAST or CRNT. If DTC is CRNT, proceed with Diagnosis Procedure. If DTC is PAST, clear
the DTC. Do not replace the
ABS actuator and electric unit (control unit) for a PAST DTC.
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn the ignition switch OFF
and wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT
1. Turn the ignition switch OFF.
NOTE:
Wait at least 10 seconds after turning ignition switch OFF.
2. Start the engine.
NOTE:
Wait at least 10 seconds after starting the engine.
3. Perform “Self Diagnostic Result” of “ABS”.
Is DTC
“C1130” detected?
YES-1 >> “C1130” is displayed as “CRNT”: Proceed to BRC-92, "Diagnosis Procedure".
YES-2 >> “C1130” is displayed as “PAST”: Inspection End (Erase “Self Diagnostic Result” of “ABS”).
NO-1 >> To check malfunction symptom before repair: Refer to GI-42, "
Intermittent Incident".
NO-2 >> Confirmation after repair: Inspection End.
Diagnosis ProcedureINFOID:0000000012430874
1.CHECK ENGINE SYSTEM
With CONSULT
Perform “Self Diagnostic Result” of “ENGINE”.
Is DTC detected?
YES >> Check the DTC. Refer to EC-87, "DTCIndex".
NO >> GO TO 2.
DTC Display Item
(Trouble diagnosis content) Malfunction detected condition
C1130 ENGINE SIGNAL 1
(Engine system signal) When a malfunction is detected in ECM system.
PAST DTC
CRNT DTC
• Harness or connector
• ABS actuator and electric unit (control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
• CAN communication line • Harness or connector
•ECM
• ABS actuator and electric unit (control unit)
• ABS actuator and electric unit
(control unit) power supply sys-
tem
•Fuse
• Fusible link
•Battery
• CAN communication line
Revision: August 2015 2016 Versa Note
cardiagn.com