cvt NISSAN NOTE 2016 Service Manual PDF
[x] Cancel search | Manufacturer: NISSAN, Model Year: 2016, Model line: NOTE, Model: NISSAN NOTE 2016Pages: 3641, PDF Size: 28.72 MB
Page 1395 of 3641
![NISSAN NOTE 2016 Service Manual PDF EC-268
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0222, P0223 TP SENSOR
3. Check the continuity between electric throttle
control actuator harness connector and ECM harness con-
nector.
4. Also check harness](/img/5/57363/w960_57363-1394.png "NISSAN NOTE 2016 Service Manual PDF EC-268
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0222, P0223 TP SENSOR
3. Check the continuity between electric throttle
control actuator harness connector and ECM harness con-
nector.
4. Also check harness")
EC-268
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0222, P0223 TP SENSOR
3. Check the continuity between electric throttle
control actuator harness connector and ECM harness con-
nector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK THROTTLE POSITION SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check the continuity between electric throttle control actuator harness connector and ECM harness con-
nector.
2. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
5.CHECK THROTTLE POSITION SENSOR
Refer to EC-268, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 7.
NO >> GO TO 6.
6.REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
Replace electric throttle control actuator. Refer to EM-28, "
Removal and Installation".
>> INSPECTION END
7.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000012431475
1.CHECK THROTTLE POSITION SENSOR
1. Turn ignition switch OFF.
2. Reconnect all harness connectors disconnected.
3. Perform EC-129, "
Description".
4. Turn ignition switch ON.
5. Set selector lever to D (CVT) or 1st (M/T) position.
6. Check the voltage between ECM harness connector and ground.
Electric throttle control actuator ECM
Continuity
Connector Terminal Connector Terminal
F7 4F11 36 Existed
Electric throttle control actuator ECM
Continuity
Connector Terminal Connector Terminal
F7 1F11 33 Existed
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1460 of 3641
![NISSAN NOTE 2016 Service Manual PDF P0500 VSSEC-333
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Go to EC-333, "Diagnosis Procedure".
NO >> INSPECTION END
5.P](/img/5/57363/w960_57363-1459.png "NISSAN NOTE 2016 Service Manual PDF P0500 VSSEC-333
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Go to EC-333, \"Diagnosis Procedure\".
NO >> INSPECTION END
5.P")
P0500 VSSEC-333
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Go to EC-333, "Diagnosis Procedure".
NO >> INSPECTION END
5.PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to EC-333, "
Component Function Check".
Use component function check to che ck the overall function of the vehicle speed signal circuit. During this
check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Go to EC-333, "
Diagnosis Procedure".
Component Function CheckINFOID:0000000012431526
1.PERFORM COMPONENT FUNCTION CHECK
With GST
1. Lift up drive wheels.
2. Start engine.
3. Read vehicle speed signal in Service $01 with GST. The vehicle speed signal on GST should be able to ex ceed 10 km/h (6 MPH) when rotating wheels with
suitable gear position.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Go to EC-333, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012431527
1.CHECK DTC WITH ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT)
Check DTC with ABS actuator and elec tric unit (control unit). Refer to BRC-43, "
DTC Index".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or replace.
2.CHECK DTC WITH COMBINATION METER
Check DTC with combination meter. Refer to MWI-24, "
DTC Index".
>> INSPECTION END
ENG SPEED 1,400 - 6,000 rpm (CVT)
1,900 - 6,000 rpm (M/T)
COOLAN TEMP/S More than 70°C (158 °F)
B/FUEL SCHDL 6.2 - 31.8 msec (CVT)
4.5 - 31.8 msec (M/T)
Shift lever Except P or N position (CVT)
Except Neutral position (M/T)
PW/ST SIGNAL OFF
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1468 of 3641
![NISSAN NOTE 2016 Service Manual PDF P0524 ENGINE OIL PRESSUREEC-341
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0524 ENGINE OIL PRESSURE
DTC LogicINFOID:0000000012431540
DTC DETECTION LOGIC
NOTE:
If DTC P0524 is](/img/5/57363/w960_57363-1467.png "NISSAN NOTE 2016 Service Manual PDF P0524 ENGINE OIL PRESSUREEC-341
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0524 ENGINE OIL PRESSURE
DTC LogicINFOID:0000000012431540
DTC DETECTION LOGIC
NOTE:
If DTC P0524 is")
P0524 ENGINE OIL PRESSUREEC-341
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P0524 ENGINE OIL PRESSURE
DTC LogicINFOID:0000000012431540
DTC DETECTION LOGIC
NOTE:
If DTC P0524 is displayed with DTC P0520 or P0075,
perform trouble diagnosis for DTC P0520 or P0075
first. Refer to EC-339, "
DTC Logic" or EC-180, "DTC Logic".
DTC CONFIRMATION PROCEDURE
CAUTION:
If “Diagnosis Procedure” is unfinish ed, be sure to perform Step 3 and 4.
1.PRECONDITIONING-I
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is 11 V or more at idle.
>> GO TO 2.
2.PRECONDITIONING-II
Is
“Diagnosis Procedure” of DTC P0524 finished?
YES >> GO TO 5.
NO >> GO TO 3.
3.CHECK ENGINE OIL LEVEL
Check engine oil level. Refer to LU-7, "
Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Proceed to EC-342, "
Diagnosis Procedure"
4.CHECK ENGINE OIL PRESSURE
WITH CONSULT
1. Turn ignition switch ON.
2. Select “DATA MONITOR” mode of “ENGINE” using CONSULT.
3. Start the engine and check that “EOP SENSOR” changes, according to engine speeds.
Without CONSULT
DTC No. CONSULT screen terms
(Trouble diagnosis content) Detecting condition
Possible cause
P0524 ENGINE OIL PRESSURE
(Engine oil pressure too low) An engine oil pressure sensor signal
voltage applied to ECM remains lower
than the specified value continuously for
10 seconds or more when the engine
speed is 1,000 rpm or more. • Decrease in engine oil pressure
• Decrease in engine oil level
• Engine oil condition
• Engine oil pressure sensor
• Engine body
Monitor item
Condition Va l u e
(Approx.)
EOP SENSOR • Engine oil temperature: 80
°C (176 °F)
• Selector lever: P or N position (CVT), Neutral position (M/T)
• Air conditioner switch: OFF
• No load Engine speed:
600 rpm
1,053 mV or more
Engine speed:
2,000 rpm 1,802 mV or more
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 1469 of 3641
![NISSAN NOTE 2016 Service Manual PDF EC-342
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0524 ENGINE OIL PRESSURE
Check engine oil level. Refer to
LU-7, "Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Proceed to EC-342, "
Di](/img/5/57363/w960_57363-1468.png "NISSAN NOTE 2016 Service Manual PDF EC-342
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0524 ENGINE OIL PRESSURE
Check engine oil level. Refer to
LU-7, \"Inspection\".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Proceed to EC-342, \"
Di")
EC-342
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0524 ENGINE OIL PRESSURE
Check engine oil level. Refer to
LU-7, "Inspection".
Is the inspection result normal?
YES >> GO TO 5.
NO >> Proceed to EC-342, "
Diagnosis Procedure"
5.PERFORM DTC CONFIRMATION PROCEDURE
1. Start engine and warm it up to normal operating temperature.
2. Maintain the following conditions for about 10 consecutive seconds.
NOTE:
With engine speed set around 4,000 rpm, the phenomenon can be reproduced more easily.
3. Check DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-342, "Diagnosis Procedure"
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431541
1.CHECK ENGINE OIL LEVEL
1. Turn ignition switch OFF.
2. Check engine oil level. Refer to LU-7, "
Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> GO TO 4.
2.CHECK ENGINE OIL PRESSURE
WITH CONSULT
1. Turn ignition switch ON.
2. Select “DATA MONITOR” mode of “ENGINE” using CONSULT.
3. Start the engine and check that “EOP SENSOR” changes, according to engine speeds.
Without CONSULT
Check engine oil level. Refer to LU-7, "
Inspection".
Is the inspection result normal?
YES >> GO TO 3.
NO >> Check oil pressure. Refer to LU-7, "
Inspection".
3.CHECK ENGINE OIL PRESSURE SENSOR
Check engine oil pressure sensor. Refer to EC-340, "
Component Inspection".
Is the inspection result normal?
YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Replace engine oil pressure sensor. Refer to EM-93, "
Exploded View".
4.CHECK ENGINE OIL LEAKAGE
Check engine oil leakage. Refer to LU-7, "
Inspection".
Selector leverP or N position (CVT)
Neutral position (M/T)
Engine coolant temperature 70° C (158°F) or more
Engine speed 1,000 rpm or more
Monitor item Condition Va l u e
(Approx.)
EOP SENSOR • Engine oil temperature: 80°
C (176°F)
• Selector lever: P or N position (CVT), Neutral position (M/T)
• Air conditioner switch: OFF
•No load Engine speed:
600 rpm
1,053 mV or more
Engine speed:
2,000 rpm 1,802 mV or more
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 1485 of 3641
![NISSAN NOTE 2016 Service Manual PDF EC-358
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0850 PNP SWITCH
P0850 PNP SWITCH
DescriptionINFOID:0000000012431556
When the selector lever position is Neutral posit
ion, park/neutral position (PNP) signal](/img/5/57363/w960_57363-1484.png "NISSAN NOTE 2016 Service Manual PDF EC-358
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0850 PNP SWITCH
P0850 PNP SWITCH
DescriptionINFOID:0000000012431556
When the selector lever position is Neutral posit
ion, park/neutral position (PNP) signal")
EC-358
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0850 PNP SWITCH
P0850 PNP SWITCH
DescriptionINFOID:0000000012431556
When the selector lever position is Neutral posit
ion, park/neutral position (PNP) signal is ON.
DTC LogicINFOID:0000000012431557
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.INSPECTION START
Do you have CONSULT?
Do you have CONSULT?
YES >> GO TO 2.
NO >> GO TO 5.
2.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following procedure
before conducting the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 3.
3.CHECK PNP SIGNAL FUNCTION
With CONSULT
1. Turn ignition switch ON.
2. Select “P/N POSI SW” in “DATA MONITOR” mode with CONSULT. Then chec k “P/N POSI SW” signal
under the following conditions.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Proceed to EC-359, "
Diagnosis Procedure".
4.PERFORM DTC CONFIRMATION PROCEDURE
1. Select “DATA MONITOR” mode with CONSULT.
2. Start engine and warm it up to normal operating temperature.
3. Maintain the following conditions for at least 50 consecutive seconds. CAUTION:
Always drive vehicle at a safe speed.
DTC No. Trouble diagnosis content DTC detecting condition Possible cause
P0850 Park/neutral position signal The park/neutral position (PNP) signal
is not changed in the process of en-
gine starting and driving.• Harness or connectors
[The park/neutral position (PNP) signal circuit
is open or shorted.]
• Transmission range switch (CVT models)
• Park/neutral position (PNP) switch (M/T mod- els)
Shift lever position Known-good signal
N or P position (CVT)
Neutral position (M/T) ON
Except above position OFF
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1486 of 3641
![NISSAN NOTE 2016 Service Manual PDF P0850 PNP SWITCHEC-359
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-359, "Diagnosis Procedure".
NO >> INSPEC](/img/5/57363/w960_57363-1485.png "NISSAN NOTE 2016 Service Manual PDF P0850 PNP SWITCHEC-359
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-359, \"Diagnosis Procedure\".
NO >> INSPEC")
P0850 PNP SWITCHEC-359
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Proceed to EC-359, "Diagnosis Procedure".
NO >> INSPECTION END
5.PERFORM COMPONENT FUNCTION CHECK
Perform component function check. Refer to EC-359, "
Component Function Check".
NOTE:
Use component function check the overall function of the park/neutral position (PNP) signal circuit. During this
check, a 1st trip DTC might not be confirmed.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Go to EC-359, "
Diagnosis Procedure".
Component Function CheckINFOID:0000000012431558
1.PERFORM COMPONENT FUNCTION CHECK
1. Turn ignition switch ON.
2. Check the voltage between ECM harness connector and ground.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Go to EC-359, "
Diagnosis Procedure".
Diagnosis ProcedureINFOID:0000000012431559
1.CHECK TRANSMISSION RANGE SWITCH (CVT) OR PARK/NEUTRAL POSITION (PNP) SWITCH (M/T)
POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect transmission range switch (CVT) or PNP switch (M/T) harness connector.
3. Turn ignition switch ON.
4. Check the voltage between transmission range switch (CVT) or PNP switch (M/T) harness connector and
ground.
Is the inspection result normal?
YES >> GO TO 3.
ENG SPEED 1,000 - 6,375 rpm
COOLAN TEMP/S More than 65°C (149 °F)
B/FUEL SCHDL 2.0 - 31.9 msec
VHCL SPEED SE More than 64 km/h (40 mph)
Shift lever Suitable position
ECM
ConditionVoltage
+ −
Connector Terminal Connector Terminal
F11 69
(PNP
signal) E16 108
Shift
lever P or N (CVT)
Neutral (M/T)
Battery voltage
Except above Approx. 0 V
Transmission range switch (CVT) / PNP switch (M/T) GroundVoltage
Connector Terminal
F52 (CVT) 7
Ground Battery voltage
F24 (M/T) 2
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1487 of 3641
![NISSAN NOTE 2016 Service Manual PDF EC-360
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0850 PNP SWITCH
NO >> GO TO 2.
2.DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E7, M69 (M/T)
• Harness connectors E55, F55
• IPDM](/img/5/57363/w960_57363-1486.png "NISSAN NOTE 2016 Service Manual PDF EC-360
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0850 PNP SWITCH
NO >> GO TO 2.
2.DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E7, M69 (M/T)
• Harness connectors E55, F55
• IPDM")
EC-360
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P0850 PNP SWITCH
NO >> GO TO 2.
2.DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E7, M69 (M/T)
• Harness connectors E55, F55
• IPDM E/R harness connector E45 (CVT)
• 10 A fuse (No. 3) (M/T)
• 10 A fuse (No. 49) (CVT)
• Harness for open or short between transmission r ange switch (CVT) or PNP switch (M/T) and fuse
Is the inspection result normal?
>> Repair open circuit or short to ground or short to power in harness or connectors.
3.CHECK PNP SWITCH INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connector.
3. Check the continuity between transmission range sw itch (CVT) or PNP switch (M/T) harness connector
and ECM harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK TRANSMISSION RANGE SWIT CH (CVT) OR PNP SWITCH (M/T)
Refer to TM-148, "
Component Inspection (Transmission Range Switch)" (CVT) or TM-15, "PA R K / N E U T R A L
POSITION (PNP) SWITCH : Component Inspection" (M/T).
Is the inspection result normal?
YES >> GO TO 5.
NO >> Replace transmission range switch (CVT) or PNP switch (M/T). Refer t\
o TM-259, "
Removal and
Installation" (CVT) or TM-24, "Removal and Installation" (M/T).
5.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> INSPECTION END
Transmission range switch (CVT) / PNP switch (M/T) ECM
Continuity
Connector Terminal Connector Terminal
F52 (CVT) 10
F11 69 Existed
F24 (M/T) 3
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1523 of 3641
![NISSAN NOTE 2016 Service Manual PDF EC-396
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P1805 BRAKE SWITCH
P1805 BRAKE SWITCH
DTC LogicINFOID:0000000012431608
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. T](/img/5/57363/w960_57363-1522.png "NISSAN NOTE 2016 Service Manual PDF EC-396
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P1805 BRAKE SWITCH
P1805 BRAKE SWITCH
DTC LogicINFOID:0000000012431608
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. T")
EC-396
< DTC/CIRCUIT DIAGNOSIS >[HR16DE]
P1805 BRAKE SWITCH
P1805 BRAKE SWITCH
DTC LogicINFOID:0000000012431608
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Turn ignition switch ON.
2. Fully depress the brake pedal for at least 5 seconds.
3. Erase DTC.
4. Check 1st trip DTC.
Is 1st trip DTC detected?
YES >> Go to EC-396, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431609
1.CHECK STOP LAMP SWITCH CIRCUIT
1. Turn ignition switch OFF.
2. Check the stop lamp when depressing and releasing the brake pedal.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
2.CHECK STOP LAMP SWIT CH POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch harness connector.
3. Check the voltage between stop lamp switch harness connector and ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 3.
3.DETECT MALFUNCTIONING PART
Check the following.
• 10 A fuse (No. 30)
• Harness for open or short between stop lamp switch and battery
>> Repair open circuit or short to ground or short to power in harness or connectors.
DTC No. Trouble diagnosis content DTC detecting condition Possible cause
P1805 Brake switch A brake switch signal is not sent to ECM
for extremely long time while the vehicle is
driving. • Harness or connectors
(Stop lamp switch circuit is open or shorted.)
• Stop lamp switch
Brake pedal Stop lamp
Fully released Not illuminated
Slightly depressed Illuminated
Sto p l am p s w it ch
Ground Voltage
Connector Terminal
E57 (M/T)
E13 (CVT) 1
Ground Battery voltage
Revision: August 2015 2016 Versa Note
cardiagn.com
Page 1524 of 3641
![NISSAN NOTE 2016 Service Manual PDF P1805 BRAKE SWITCHEC-397
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4.CHECK STOP LAMP SWITCH INPUT SI
GNAL CIRCUIT FOR OPEN AND SHORT
1. Disconnect stop lamp switch harness con](/img/5/57363/w960_57363-1523.png "NISSAN NOTE 2016 Service Manual PDF P1805 BRAKE SWITCHEC-397
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4.CHECK STOP LAMP SWITCH INPUT SI
GNAL CIRCUIT FOR OPEN AND SHORT
1. Disconnect stop lamp switch harness con")
P1805 BRAKE SWITCHEC-397
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
4.CHECK STOP LAMP SWITCH INPUT SI
GNAL CIRCUIT FOR OPEN AND SHORT
1. Disconnect stop lamp switch harness connector.
2. Disconnect ECM harness connector.
3. Check the continuity between ECM harness connector and stop lamp switch harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal?
YES >> GO TO 5.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
5.CHECK STOP LAMP SWITCH
Refer to EC-397, "
Component Inspection".
Is the inspection result normal?
YES >> GO TO 6.
NO >> Replace brake pedal assembly. Refer to BR-20, "
Removal and Installation".
6.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "
Intermittent Incident".
>> INSPECTION END
Component InspectionINFOID:0000000012431610
1.CHECK STOP LAMP SWITCH-I
1. Turn ignition switch OFF.
2. Disconnect stop lamp switch harness connector.
3. Check the continuity between stop lamp switch terminals under the following conditions.
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 2.
2.CHECK STOP LAMP SWITCH-II
1. Adjust stop lamp switch installation. Refer to BR-21, "
Inspection and Adjustment".
2. Check the continuity between stop lamp switch terminals under the following conditions.
Is the inspection result normal?
YES >> INSPECTION END
NO >> Replace brake pedal assembly. Refer to BR-20, "
Removal and Installation".
ECM Stop lamp switch
Continuity
Connector Terminal Connector Terminal
E16 99E57 (M/T)
E13 (CVT) 2 Existed
Terminals
ConditionContinuity
1 and 2 Brake pedal Fully released Not existed
Slightly depressed Existed
Terminals
ConditionContinuity
1 and 2 Brake pedal Fully released Not existed
Slightly depressed Existed
Revision: August 2015
2016 Versa Note
cardiagn.com
Page 1538 of 3641
![NISSAN NOTE 2016 Service Manual PDF P2119 ELECTRIC THROTTLE CONTROL ACTUATOREC-411
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
DTC LogicINFOID:0000000012431621
DTC DETECTIO](/img/5/57363/w960_57363-1537.png "NISSAN NOTE 2016 Service Manual PDF P2119 ELECTRIC THROTTLE CONTROL ACTUATOREC-411
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
DTC LogicINFOID:0000000012431621
DTC DETECTIO")
P2119 ELECTRIC THROTTLE CONTROL ACTUATOREC-411
< DTC/CIRCUIT DIAGNOSIS > [HR16DE]
C
D
E
F
G H
I
J
K L
M A
EC
NP
O
P2119 ELECTRIC THROTTLE CONTROL ACTUATOR
DTC LogicINFOID:0000000012431621
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If DTC Confirmation Procedure has been previously conducted, always perform the following before conduct-
ing the next test.
1. Turn ignition switch OFF and wait at least 10 seconds.
2. Turn ignition switch ON.
3. Turn ignition switch OFF and wait at least 10 seconds.
>> GO TO 2.
2.PERFORM DTC CONFIRMATION PROC EDURE FOR MALFUNCTION A AND B
1. Turn ignition switch ON and wait at least 1 second.
2. Set selector lever to D (CVT) or 1st (M/T) position and wait at least 3 seconds.
3. Set selector lever to P (CVT) or Neutral (M/T) position.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Turn ignition switch ON and wait at least 1 second.
6. Set selector lever to D (CVT) or 1st (M/T) position and wait at least 3 seconds.
7. Set selector lever to P (CVT) or Neutral (M/T) position.
8. Turn ignition switch OFF, wait at least 10 seconds and then turn ON.
9. Check DTC.
Is DTC detected?
YES >> Go to EC-411, "Diagnosis Procedure".
NO >> GO TO 3.
3.PERFORM DTC CONFIRMATION PROCEDURE FOR MALFUNCTION C
1. Turn ignition switch ON and wait at least 1 second.
2. Set selector lever to D (CVT) or 1st (M/T) position and wait at least 3 seconds.
3. Set selector lever to P (CVT) or Neutral (M/T) position.
4. Start engine and let it idle for 3 seconds.
5. Check DTC.
Is DTC detected?
YES >> Go to EC-411, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis ProcedureINFOID:0000000012431622
1.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1. Turn ignition switch OFF.
2. Remove the intake air duct. Refer to EM-26, "
Removal and Installation".
DTC No. Trouble diagnosis content DTC detecting conditionPossible cause
P2119 Electric throttle control ac-
tuator A)
Electric throttle control actuator does not function
properly due to the return spring malfunction.
Electric throttle control actuator
B) Throttle valve opening angle in fail-safe mode is
not in specified range.
C) ECM detect the throttle valve is stuck open.
Revision: August 2015 2016 Versa Note
cardiagn.com