Stop NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide PATROL 1998 Y61 / 5.G NISSAN NISSAN https://www.carmanualsonline.info/img/5/616/w960_616-0.png NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide

Page 74 of 326

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide System Description
CIRCUIT OPERATION
[Example]
Aiming switch ``0
+When the aiming switch is set to ``0, the motor will not start.
This is because the power terminals are positioned at the non-
con

Page 81 of 326

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide Wiring Diagram Ð STOP/L Ð/Type A
Rear combination lamps are located on rear bumper.
YEL788A
Stop Lamp
EL-77

Page 119 of 326

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide FUEL TANK GAUGE UNIT CHECK
+For removal, refer to FE section.
Check the resistance between terminalsj
1andj2.
Ohmmeter
Float position
mm (in)Resistance value
(W)
(+) (þ)
j
1j2
*1 Full 60 (2.36) Appro

Page 123 of 326

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide a) The temperature detected by the ambient air temperature sensor is lower than the indicated tem-
perature on the thermometer.
b) The difference in temperature detected during a period of 40 seconds

Page 138 of 326

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide Electrical Components Inspection
FUEL WARNING LAMP SENSOR CHECK
+It will take a short time for the bulb to light.
NOTE: Inspection for sub fuel warning lamp sensor is the
same as for fuel warning lamp

Page 145 of 326

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide System Description
WIPER OPERATION
The wiper switch is controlled by a lever built into the combination switch.
There are three wiper switch positions:
+LO speed
+HI speed
+INT (Intermittent)
With the

Page 147 of 326

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide Removal and Installation
WIPER ARMS
1. Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it ``OFF (Auto Stop).
2. Lift the blade up and then set it down onto

Page 149 of 326

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide System Description
WIPER OPERATION
The rear wiper switch is controlled by a ring built into the combination switch.
There are two wiper switch positions:
+ON (LO speed)
+INT (Intermittent)
With the ig

Page 154 of 326

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide Trouble Diagnoses
REAR WIPER AMP. INSPECTION TABLE
(Data are reference values.)
Terminal No. Item ConditionVoltage
(Approximate value)
1 Intermittent switch
Rear wiper switchINT Less than 1V
OFF, ON o

Page 155 of 326

NISSAN PATROL 1998 Y61 / 5.G Electrical System User Guide Removal and Installation
WIPER ARM
1. Prior to wiper arm installation, turn on wiper switch to operate
wiper motor and then turn it ``OFF (Auto Stop).
2. Lift the blade up and then set it down onto
Page:   < prev 1-10 11-20 21-30 next >