wheel alignment NISSAN TEANA 2008 Owner's Guide

ST-12
< ON-VEHICLE REPAIR >
STEERING WHEEL
ON-VEHICLE REPAIR
STEERING WHEEL
Exploded ViewINFOID:0000000003806314
Removal and InstallationINFOID:0000000003806315
REMOVAL
NOTE:
When reconnecting spiral cable, fix cable with a tape so that fixing case and rotating part keep aligned. This
will omit neutral position alignment procedure during spiral cable installation.
1. Set the vehicle to the straight-ahead position.
2. Remove driver air bag module. Refer to SR-6, "
Exploded View".
3. Remove steering wheel lock nut after steering is locked.
4. Remove steering wheel with the steering wheel puller (A) (SST:
ST27180001).
INSTALLATION
Note the following, and install in the reverse order of removal.
CAUTION:
Never twist spiral cable freely on excessively after it becomes tight (doing so may cause the cable to
tear off).
NOTE:
Check the spiral cable neutral position after replacing or rotating spiral cable. Refer to SR-9, "
Exploded View".
1. Steering wheel
Refer to GI-4, "
Components" for symbols in the figure.
JSGIA0303GB
JSGIA0391ZZ

ST-20
< ON-VEHICLE REPAIR >
STEERING GEAR AND LINKAGE
 When installing low pressure hose (1), refer to the figure.
CAUTION:
 Never apply fluid to the hose (1) and tube (2).
 Insert hose securely until it contacts spool (A) of tube.
 Leave clearance (L) when installing clamp (3).
 When installing lower joint to steering gear assembly, follow the procedure listed below.
- Set rack of steering gear in the neutral position.
NOTE:
To get the neutral position of rack, turn gear-sub assembly and measure the distance of inner socket, and
then measure the intermediate position of the distance.
- Align rear cover cap projection (A) with the marking position of
gear housing assembly (B).
- Install slit part of lower joint (C) aligning with the rear cover cap
projection (A). Make sure that the slit part of lower joint (C) is
aligned with rear cover cap projection (A) and the marking position
of gear housing assembly (B).
 After installation, bleed air from the steering hydraulic system.
Refer to ST-32, "
Inspection".
 Perform final tightening of nuts and bolts on each part under
unladen conditions with tires on level ground when removing steer-
ing gear assembly. Check wheel alignment. Refer to FSU-7, "
Wheel Alignment Inspection".
 Adjust neutral position of steering angle sensor after checking wheel alignment. Refer to BRC-66, "
ADJUST-
MENT OF STEERING ANGLE SENSOR NEUTRAL POSITION : Special Repair Requirement" (VDC mod-
els).
Disassembly and AssemblyINFOID:0000000003806324
DISASSEMBLY
1. Remove low pressure piping.
CAUTION:
 Disassemble and assemble steering gear assembly by fixing the mounting area with a vise using
copper plates.
 Clean steering gear assembly with kerosene before disassembling. Be careful to avoid splash-
ing or applying any kerosene over connector of discharge port or return port.
2. Remove cylinder tubes from gear housing assembly.
3. Remove rear cover cap from gear-sub assembly.
4. Measure adjusting screw height “H”, and loosen adjusting
screw.
CAUTION:
 Never loosen adjusting screw 2 turns or more.
 Replace steering gear assembly if adjusting screw is
loosened 2 turns or more and it is removed.
5. Remove gear-sub assembly from gear housing assembly.
6. Remove O-ring from gear housing assembly.
7. Loosen outer socket lock nut, and remove outer socket.
8. Remove boot clamps, and then remove boot from inner socket.
CAUTION:Standard
L : 3 – 8 mm (0.12 – 0.31 in)
JSGIA0118ZZ
: Bolt
J S G I A 0 111 Z Z
SGIA0624E