timing NISSAN TEANA 2014 Service Manual

ECM
EC-613
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
ECU DIAGNOSIS INFORMATION
ECM
Reference ValueINFOID:0000000009462542
VALUES ON THE DIAGNOSIS TOOL
NOTE:
• The following table includes information (items) inapplicable to this vehicle. For information (items) applica- ble to this vehicle, refer to CONSULT display items.
• Numerical values in the following table are reference values.
• These values are input/output values that ECM receiv es/transmits and may differ from actual operations.
Example: The ignition timing shown by the timing light may differ from the ignition timing displayed on the
data monitor.
This occurs because the timing light shows a value calculated by ECM according to signals received from
the camshaft position sensor and other sensors related to ignition timing.
• For outlines of following items, refer to EC-601, "CONSULT Function"
.
Monitor Item Condition Values/Status
ENG SPEED Run engine and compare CONSULT value with the tachometer indication.Almost the same speed as
the tachometer indication.
MAS A/F SE-B1 See EC-701, "Description"
.
B/FUEL SCHDL See EC-701, "Description"
.
A/F ALPHA-B1 See EC-701, "Description"
.
A/F ALPHA-B2 See EC-701, "Description"
.
COOLAN TEMP/S Engine: After warming up More than 70 °C (158 °F)
A/F SEN1 (B1) Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 2.2 V
A/F SEN1 (B2) Engine: After warming up Maintaining engine speed at 2,000 rpm Fluctuates around 2.2 V
HO2S2 (B1) Revving engine from idle to 3,000 rpm quickly after the following conditions are
met.
• Engine: After warming up
• After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load 0 - 0.3 V
←→ Approx. 0.6 -
1.0 V
HO2S2 (B2) Revving engine from idle to 3,000 rpm quickly after the following conditions are
met.
• Engine: After warming up
• After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at
idle for 1 minute under no load 0 - 0.3 V
←→ Approx. 0.6 -
1.0 V
HO2S2 MNTR(B1) Revving engine from idle to 3,000 rpm quickly after the following conditions are
met.
• Engine: After warming up
• After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load LEAN
←→ RICH
HO2S2 MNTR(B2) Revving engine from idle to 3,000 rpm quickly after the following conditions are
met.
• Engine: After warming up
• After keeping engine speed between 3,500 and 4,000 rpm for 1 minute and at idle for 1 minute under no load LEAN
←→ RICH
VHCL SPEED SE Turn drive wheels and compare CONSULT value with the speedometer indica-
tion. Almost the same speed as
speedometer indication
BATTERY VOLT Ignition switch: ON (Engine stopped) 11 - 14 V
ACCEL SEN 1 Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released 0.5 - 1.0 V
Accelerator pedal: Fully depressed 4.2 - 4.8 V
ACCEL SEN 2*
1Ignition switch: ON
(Engine stopped) Accelerator pedal: Fully released 0.5 - 1.0 V
Accelerator pedal: Fully depressed 4.2 - 4.8 V
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-614
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
TP SEN 1-B1• Ignition switch: ON
(Engine stopped)
• Selector lever: D position Accelerator pedal: Fully re
leased More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
TP SEN 2-B1*
1• Ignition switch: ON (Engine stopped)
• Selector lever: D position Accelerator pedal: Fully re
leased More than 0.36 V
Accelerator pedal: Fully depressed Less than 4.75 V
FUEL T/TMP SE Ignition switch: ON Indicates fuel tank tempera-
ture
EVAP SYS PRES Ignition switch: ON Approx. 1.8 - 4.8 V
FUEL LEVEL SE Ignition switch: ON Depending on fuel level of
fuel tank
START SIGNAL Ignition switch: ON → START → ON Off → On → Off
CLSD THL POS Ignition switch: ON
(Engine stopped) Accelerator pedal:
Fully released On
Accelerator pedal: Slightly depressed Off
AIR COND SIG Engine: After warming up, idle the
engine Air conditioner switch: OFF Off
Air conditioner switch: ON
(Compressor operates.) On
PW/ST SIGNAL Engine: After warming up, idle the
engine Steering wheel: Not being turned Off
Steering wheel: Being turned On
LOAD SIGNAL Ignition switch: ON Rear window defogger switch: ON
and/or
Lighting switch: 2nd position On
Rear window defogger switch and lighting
switch: OFF Off
IGNITION SW Ignition switch: ON → OFF → ON On → Off → On
HEATER FAN SW Engine: After warming up, idle the
engine Heater fan switch: ON On
Heater fan switch: OFF Off
BRAKE SW Ignition switch: ON Brake pedal: Fully released Off
Brake pedal: Slightly depressed On
INJ PULSE-B1 • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 2.0 - 3.0 msec
2,000 rpm 1.9 - 2.9 msec
INJ PULSE-B2 • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 2.0 - 3.0 msec
2,000 rpm 1.9 - 2.9 msec
IGN TIMING • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 7 - 17
°BTDC
2,000 rpm 25 - 45 °BTDC
CAL/LD VALUE • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 5 - 35%
2,500 rpm 5 - 35%
MASS AIRFLOW • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle 2.0 - 6.0 g/s
2,500 rpm 7.0 - 20.0 g/s
PURG VOL C/V • Engine: After warming up
• Selector lever: P or N position
• Air conditioner switch: OFF
•No load Idle
(Accelerator pedal: Not depressed even
slightly, after engine starting.) 0%
2,000 rpm —
Monitor Item Condition Values/Status
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-622
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
41
(LG) 128
(GR) Heated oxygen sensor 2 heat-
er (bank 2) Output[Engine is running]
Engine speed: Below 3,600 rpm
after the following conditions are
met
• Engine: after warming up
• Keeping the engine speed be- tween 3,500 and 4,000 rpm
for 1 minute and at idle for 1
minute under no load 10 V
• [Ignition switch: ON] Engine stopped
• [Engine is running] Engine speed: Above 3,600
rpm BATTERY VOLTAGE
(11 - 14 V)
42
(BR) 128
(GR) EVAP canister purge volume
control solenoid valve Output[Engine is running]
• Idle speed
• Accelerator pedal: Not de- pressed even slightly, after
engine starting BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
Engine speed: approximately
2,000 rpm (More than 100 sec-
onds after starting engine) BATTERY VOLTAGE
(11 - 14 V)
43
(V) 128
(GR) Fuel pump relay Output • [Ignition switch: ON]
For 1 second after turning ig-
nition switch ON
• [Engine is running] 0 - 1.0 V
54
(V) 84
(SB) Sensor power supply
[Crankshaft position sensor
(POS)] — [Ignition switch: ON] 5 V
55
(Y) 128
(GR) Intake valve timing control so-
lenoid valve (bank 1) Output[Engine is running]
• Warm-up condition
• Idle speed BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 7 - 12 V
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
JMBIA0902GB
JMBIA0039GB
JMBIA0040GB
JMBIA0038GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

ECM
EC-623
< ECU DIAGNOSIS INFORMATION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
56
(BR) 128
(GR) Intake valve timing control so-
lenoid valve (bank 2) Output[Engine is running]
• Warm-up condition
• Idle speed BATTERY VOLTAGE
(11 - 14 V)
[Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 7 - 12 V
57
(L) 128
(GR) Heated oxygen sensor 2
(bank 1) Input[Engine is running]
Revving engine from idle to
3,000 rpm quickly after the fol-
lowing conditions are met
• Engine: after warming up
• Keeping the engine speed be- tween 3,500 and 4,000 rpm
for 1 minute and at idle for 1
minute under no load 0 - 1.0 V
58
(L) 128
(GR) Heated oxygen sensor 2
(bank 2) Input[Engine is running]
Revving engine from idle to
3,000 rpm quickly after the fol-
lowing conditions are met
• Engine: after warming up
• Keeping the engine speed be-
tween 3,500 and 4,000 rpm
for 1 minute and at idle for 1
minute under no load 0 - 1.0 V
59
(L) —Sensor ground
(Heated oxygen sensor 2) —— —
63
(W) 64
(P) Refrigerant pressure sensor Input [Engine is running]
• Warm-up condition
• Both A/C switch and blower
fan motor switch: ON (Com-
pressor operates) 1.0 - 4.0 V
64
(P) —Sensor ground
(Refrigerant pressure sensor) —— —
66
(G) 68
(R) Battery current sensor Input [Engine is running]
• Battery: Fully charged*
2
• Idle speed 2.6 - 3.5 V
67
(W) 68
(R) Battery temperature sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with battery temperature.
68
(R) —Sensor ground
(Battery curre nt sensor) —— —
69
(W) 128
(GR) A/F sensor 1 (bank 1) Input [Engine is running]
• Warm-up condition
• Engine speed: 2,000 rpm 2.2 V
Output voltage varies with air fuel ratio.
70
(BR) 76
(B) Engine coolant temperature
sensor Input [Engine is running] 0 - 4.8 V
Output voltage varies with engine
coolant temperature.
73
(B) 128
(GR) A/F sensor 1 (bank 1) Input [Ignition switch: ON] 1.8 V
Terminal No. Description
ConditionVa l u e
(Approx.)
+ -– Signal name Input/
Output
JMBIA0038GB
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-628
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
DTC RELATED ITEM
Engine operating condi-
tion in fail-safe mode Detected items Remarks
Reference
page
Engine speed will not
rise more than 2,500 rpm
due to the fuel cut Malfunction indicator
lamp circuit When there is an open circuit on MIL circuit, the ECM cannot warn the
driver by illuminating MIL when there is malfunction on engine control
system.
Therefore, when electrical controlled throttle and part of ECM related
diagnoses are continuously detected as NG for 5 trips, ECM warns the
driver that engine control system malfunctions and MIL circuit is open
by means of operating the fail-safe function.
The fail-safe function also operates when above diagnoses except MIL
circuit are detected and demands the driver to repair the malfunction. EC-973
DTC No. Detected items Engine operating condition in fail-safe mode
P0011
P0021 Intake valve timing control The signal is not energized to the intake valve timing control solenoid valve and the valve
control does not function.
P0101
P0102
P0103 Mass air flow sensor circuit Engine speed will not rise more than 2,400 rpm due to the fuel cut.
P0117
P0118 Engine coolant tempera-
ture sensor circuit Engine coolant temperature will be determined by ECM based on the following condition.
CONSULT displays the engine coolant temperature decided by ECM.
Condition Engine coolant temperature decided
(CONSULT display)
Just as ignition switch is turned ON
or START 40
°C (104 °F)
Approx 4 minutes or more after en-
gine starting 80
°C (176 °F)
Except as shown above 40 - 80
°C (104 - 176 °F)
(Depends on the time)
When the fail-safe system for engine coolant temperature sensor is activated, the cooling
fan operates while engine is running.
P0122
P0123
P0222
P0223
P2135 Throttle position sensor The ECM controls the electric throttle control actuator in regulating the throttle opening in
order for the idle position to be within +10 degrees.
The ECM regulates the opening speed of the throttle valve to be slower than the normal
condition.
Therefore, the acceleration will be poor.
P0196
P0197
P0198 Engine oil temperature
sensor Intake valve timing control does not function.
P0500 Vehicle speed sensor The cooling fan operates (Highest) while engine is running.
P0524 Engine oil pressure • ECM illuminates oil pressure warning lamp on the combination meter.
• Engine speed will not rise more than 4,000 rpm due to the fuel cut.
• Fail-safe is canceled when ignition switch OFF → ON.
P0605 ECM (When ECM calculation function is malfunctioning:) ECM stops the electric throttle control actuator control, throttle valve is maintained at a
fixed opening (approx. 5 degrees) by the return spring.
ECM deactivates ASCD operation.
P0643 Sensor power supply ECM stops the electric throttle control actuator control, throttle valve is maintained at a fixed opening (approx. 5 degrees) by the return spring.
P1805 Brake switch ECM controls the electric throttle control actuator by regulating the throttle opening to a small range.
Therefore, acceleration will be poor.
Vehicle condition Driving condition
When engine is idling Normal
When accelerating Poor acceleration
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-630
< ECU DIAGNOSIS INFORMATION >[VQ35DE]
ECM
DTC Index
INFOID:0000000009462545
× :Applicable —: Not applicable
2 P0031, P0032, P0051, P0052 Air fuel ratio (A/F) sensor 1 heater
P0037, P0038, P0057, P0058 Heated oxygen sensor 2 heater
P0075, P0081 Intake valve timing control solenoid valve
P0130, P0131, P0132, P014 C, P014D, P014E, P014F,
P0150, P0151, P0152, P209 6, P2097, P2098, P2099 Air fuel ratio (A/F) sensor 1
P0137, P0138, P0139, P0157, P0158, P0159 Heated oxygen sensor 2
P0441 EVAP control system purge flow monitoring
P0443, P0444, P0445 EVAP canister purge volume control solenoid valve
P0447, P0448 EVAP canister vent control valve
P0451, P0452, P0453 EVAP control system pressure sensor
P0603 ECM power supply
P1217 Engine over temperature (OVERHEAT)
P1800, P1801 VIAS cont rol solenoid valve
P1805 Brake switch
P2100, P2103 Throttle control motor relay
P2101 Electric throttle control function
P2118 Throttle control motor
3 P0011, P0021 Intake valve timing control P0171, P0172, P0174, P0175 Fuel injection system function
P0300 - P0306 Misfire
P0420, P0430 Three way catalyst function
P0456 EVAP control syst em (VERY SMALL LEAK)
P0506, P0507 Idle speed control system
P050A, P050E Cold start control
P0524 Engine oil pressure
P1148, P1168 Closed loop control
P1212 TCS communication line
P1564 ASCD steering switch
P1572 Brake pedal position switch
P1574 ASCD vehicle speed sensor
P2119 Electric throttle control actuator
Priority Detected items (DTC) Detected items (DTC)
DTC*1
Items
(CONSULT screen terms) SRT
code Trip MIL Permanent
DTC group*4Refer-
ence page
CONSULT
GST
*2ECM*3
U0101 0101*5LOST COMM (ECM) — 1 ×BEC-713
U1001
1001*5CAN COMM CIRCUIT — 2 — — EC-714
P0000 0000NO DTC IS DETECTED.
FURTHER TESTING
MAY BE REQUIRED. ——
Blinking*6——
P0011 0011 INT/V TIM CONT-B1 ×2 ×BEC-715
P0021 0021 INT/V TIM CONT-B2 ×2 ×BEC-715
P0031 0031 A/F SEN1 HTR (B1) — 2 ×BEC-719
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-676
< BASIC INSPECTION >[VQ35DE]
BASIC INSPECTION
2. Rev engine (2,000 to 3,000 rpm) 2 or 3 times under no load,
then run engine at idle speed for approximately 1 minute.
3. Check idle speed.
For procedure, refer to EC-992, "Work Procedure"
.
For specification, refer to EC-998, "Idle Speed"
.
Is the inspection result normal?
YES >> GO TO 10.
NO >> GO TO 4.
4.PERFORM ACCELERATOR PEDAL RE LEASED POSITION LEARNING
1. Stop engine.
2. Perform EC-681, "Work Procedure"
.
>> GO TO 5.
5.PERFORM THROTTLE VALVE CL OSED POSITION LEARNING
Perform EC-682, "Work Procedure"
.
>> GO TO 6.
6.PERFORM IDLE AIR VOLUME LEARNING
Perform EC-683, "Work Procedure"
.
Is Idle Air Volume Learning carried out successfully?
YES >> GO TO 7.
NO >> Follow the instruction of Idle Air Volume Learning. Then GO TO 4.
7.CHECK IDLE SPEED AGAIN
1. Start engine and warm it up to normal operating temperature.
2. Check idle speed.
For procedure, refer to EC-992, "Work Procedure"
.
For specification, refer to EC-998, "Idle Speed"
.
Is the inspection result normal?
YES >> GO TO 10.
NO >> GO TO 8.
8.DETECT MALFUNCTIONING PART
Check the Following.
• Check camshaft position sensor (PHASE) and circuit. Refer to EC-820, "Diagnosis Procedure"
.
• Check crankshaft position sensor (POS) and circuit. Refer to EC-817, "Diagnosis Procedure"
.
Is the inspection result normal?
YES >> GO TO 9.
NO >> Repair or replace malfunctioning part. Then GO TO 4.
9.CHECK ECM FUNCTION
1. Substitute with a non-malfunctioning ECM to check EC M function. (ECM may be the cause of the incident,
although this is rare.)
2. Perform initialization of NVIS (NAT S) system and registration of all NVIS (NATS) ignition key IDs. Refer to
SEC-66, "ECM : Work Procedure"
.
>> GO TO 4.
10.CHECK IGNITION TIMING
1. Run engine at idle.
2. Check ignition timing with a timing light.
For procedure, refer to EC-993, "Work Procedure"
.
PBIA8513J
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

BASIC INSPECTIONEC-677
< BASIC INSPECTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
For specification, refer to
EC-998, "Ignition Timing".
Is the inspection result normal?
YES >> GO TO 19.
NO >> GO TO 11.
11 .PERFORM ACCELERATOR PEDAL RELEASED POSITION LEARNING
1. Stop engine.
2. Perform EC-681, "Work Procedure"
.
>> GO TO 12.
12.PERFORM THROTTLE VALVE CLOSED POSITION LEARNING
Perform EC-682, "Work Procedure"
.
>> GO TO 13.
13.PERFORM IDLE AIR VOLUME LEARNING
Perform EC-683, "Work Procedure"
.
Is Idle Air Volume Learning carried out successfully?
YES >> GO TO 14.
NO >> Follow the instruction of Idle Air Volume Learning. Then GO TO 4.
14.CHECK IDLE SPEED AGAIN
1. Start engine and warm it up to normal operating temperature.
2. Check idle speed.
For procedure, refer to EC-992, "Work Procedure"
.
For specification, refer to EC-998, "Idle Speed"
.
Is the inspection result normal?
YES >> GO TO 15.
NO >> GO TO 17.
15.CHECK IGNITION TIMING AGAIN
1. Run engine at idle.
2. Check ignition timing with a timing light. For procedure, refer to EC-993, "Work Procedure"
.
For specification, refer to EC-998, "Ignition Timing"
.
Is the inspection result normal?
YES >> GO TO 19.
NO >> GO TO 16.
16.CHECK TIMING CHAIN INSTALLATION
Check timing chain installation. Refer to EM-182, "Exploded View"
.
Is the inspection result normal?
YES >> GO TO 17.
NO >> Repair the timing chain installation. Then GO TO 4.
17.DETECT MALFUNCTIONING PART
Check the following.
• Check camshaft position sensor (PHASE) and circuit. Refer to EC-820, "Diagnosis Procedure"
.
• Check crankshaft position sensor (POS) and circuit. Refer to EC-817, "Diagnosis Procedure"
.
Is the inspection result normal?
YES >> GO TO 18.
NO >> Repair or replace malfunctioning part. Then GO TO 4.
18.CHECK ECM FUNCTION
1. Substitute with a non-malfunctioning ECM to check EC M function. (ECM may be the cause of the incident,
although this is rare.)
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

IDLE AIR VOLUME LEARNINGEC-683
< BASIC INSPECTION > [VQ35DE]
C
D E
F
G H
I
J
K L
M A
EC
NP
O
IDLE AIR VOLUME LEARNING
DescriptionINFOID:0000000009462557
Idle Air Volume Learning is a function of ECM to learn
the idle air volume that keeps engine idle speed within
the specific range. It must be performed under the following conditions:
• Each time the electric throttle c ontrol actuator or ECM is replaced.
• Idle speed or ignition timing is out of the specification.
Work ProcedureINFOID:0000000009462558
1.PRECONDITIONING
Check that all of the following conditions are satisfied.
Learning will be cancelled if any of the following conditions are missed for even a moment.
• Battery voltage: More than 12.9 V (At idle)
• Engine coolant temperature: 70 - 100 °C (158 - 212 °F)
• Selector lever position: P or N
• Electric load switch: OFF
(Air conditioner, head lamp, rear window defogger)
On vehicles equipped with daytime light systems, if the parking brake is applied before the engine is
started the head lamp will not illuminate.
• Steering wheel: Neutral (Straight-ahead position)
• Vehicle speed: Stopped
• Transmission: Warmed-up
- With CONSULT: Drive vehicle until “ATF TEMP SEN” in “DATA MONITOR” mode of “CVT” system indicates
less than 0.9 V.
- Without CONSULT: Drive vehicle for 10 minutes.
Will CONSULT be used?
YES >> GO TO 2.
NO >> GO TO 3.
2.PERFORM IDLE AIR VOLUME LEARNING
With CONSULT
1. Perform Accelerator Pedal Released Position Learning. Refer to EC-681, "Work Procedure"
.
2. Perform Throttle Valve Closed Position Learning. Refer to EC-682, "Work Procedure"
.
3. Start engine and warm it up to normal operating temperature.
4. Select “IDLE AIR VOL LEA RN” in “WORK SUPPORT” mode.
5. Touch “START” and wait 20 seconds.
Is
“CMPLT” displayed on CONSULT screen?
YES >> GO TO 4.
NO >> GO TO 5.
3.PERFORM IDLE AIR VOLUME LEARNING
Without CONSULT
NOTE:
• It is better to count the time accurately with a clock.
• It is impossible to switch the di agnostic mode when an accelerator pedal position sensor circuit has
a malfunction.
1. Perform Accelerator Pedal Released Position Learning. Refer to EC-681, "Work Procedure"
.
2. Perform Throttle Valve Closed Position Learning. Refer to EC-682, "Work Procedure"
.
3. Start engine and warm it up to normal operating temperature.
4. Turn ignition switch OFF and wait at least 10 seconds.
5. Confirm that accelerator pedal is fully releas ed, turn ignition switch ON and wait 3 seconds.
6. Repeat the following procedure quickly 5 times within 5 seconds.
- Fully depress the accelerator pedal.
- Fully release the accelerator pedal.
7. Wait 7 seconds, fully depress the accelerator pedal for approx. 20 seconds until the MIL stops blinking
and turns ON.
8. Fully release the accelerator pedal within 3 seconds after the MIL turns ON.
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM

EC-684
< BASIC INSPECTION >[VQ35DE]
IDLE AIR VOLUME LEARNING
9. Start engine and let it idle.
10. Wait 20 seconds.
>> GO TO 4.
4.CHECK IDLE SPEED AND IGNITION TIMING
Rev up the engine 2 or 3 times and check that idle s peed and ignition timing are within the specifications.
For procedure, refer to EC-992, "Work Procedure"
and EC-993, "Work Procedure".
For specifications, refer to EC-998, "Idle Speed"
and EC-998, "Ignition Timing".
Is the inspection result normal?
YES >> INSPECTION END
NO >> GO TO 5.
5.DETECT MALFUNCTIONING PART-I
Check the following
• Check that throttle valve is fully closed.
• Check PCV valve operation.
• Check that downstream of throttle valve is free from air leakage.
Is the inspection result normal?
YES >> GO TO 6.
NO >> Repair or replace malfunctioning part.
6.DETECT MALFUNCTIONING PART-II
Engine component parts and their installation condition are questionable. Check and eliminate the cause of
the incident.
It is useful to perform “TROUBLE DIAGNOSIS - SPECIFICATION VALUE”. Refer to EC-701, "Description"
.
If any of the following conditions occur after the engi ne has started, eliminate the cause of the incident and
perform Idle Air Volume Learning again:
• Engine stalls.
• Incorrect idle.
>> INSPECTION END
SEC897C
Revision: November 20132014 Altima NAMRevision: November 20132014 Altima NAM