low oil pressure NISSAN TIIDA 2007 Service Workshop Manual

CYLINDER HEAD
EM-63
C
D
E
F
G
H
I
J
K
L
MA
EM
Revision: June 20062007 Versa

If the engine speed is out of the specified range, check battery liquid for proper gravity. Check engine
speed again with normal battery gravity.

If compression pressure is below minimum value, check valve clearances and parts associated with
combustion chamber (Valve, valve seat, piston, piston ring, cylinder bore, cylinder head, cylinder head
gasket). After the checking, measure the compression pressure again.

If some cylinder has low compression pressure, pour small amount of engine oil into the spark plug hole
of the cylinder to re-check it for compression.
–If the added engine oil improves the compression, piston rings may be worn out or damaged. Check
piston rings and replace if necessary.
–If the compression pressure remains at low level despite the addition of engine oil, valves may be mal-
functioning. Check valves for damage. Replace valve or valve seat accordingly.

If two adjacent cylinders have respectively low compression pressure and their compression remains
low even after the addition of engine oil, cylinder head gasket is leaking. In such a case, replace cylin-
der head gasket.
9. After inspection is completed, install removed parts.
10. Start the engine, and confirm that the engine runs smoothly.
11. Perform trouble diagnosis. If DTC appears, erase it. Refer to EC-83, "
TROUBLE DIAGNOSIS" .
ComponentsEBS00U7R
Removal and InstallationEBS00U7S
REMOVAL
WA RN ING:

Put a “CAUTION: FLAMMABLE” sign in the workshop.

Be sure to work in a well ventilated area and furnish workshop with a CO2 fire extinguisher.

Do not smoke while servicing fuel system. Keep open flames and sparks away from the work area.
1. Release the fuel pressure. Refer to EC-81, "
FUEL PRESSURE RELEASE" .
2. Drain engine coolant and engine oil. Refer to CO-8, "
ENGINE COOLANT" and LU-5, "ENGINE OIL" .
3. Remove front fender protector (RH). Refer to EI-22, "
FENDER PROTECTOR" .
4. Remove drive belt. Refer to EM-13, "
Removal and Installation" .
5. Remove the following components and related parts.

Exhaust manifold; Refer to EM-21, "EXHAUST MANIFOLD" .

Intake manifold; Refer to EM-18, "INTAKE MANIFOLD" .

Fuel tube and fuel injector assembly; Refer to EM-33, "FUEL INJECTOR AND FUEL TUBE" .
1. Cylinder head assembly 2. Cylinder head bolt 3. Cylinder head gasket
A. Refer to EM-65
PBIC3542J

EM-74Revision: June 2006
ENGINE ASSEMBLY
2007 Versa

Use either 2-pole lift type or separate type lift as best you can. If board-on type is used for
unavoidable reasons, support at the rear axle jacking point with a transmission jack or similar tool
before starting work, in preparation for the backward shift of center of gravity.

For supporting points for lifting and jacking point at rear axle, refer to GI-42, "Garage Jack and
Safety Stand and 2-Pole Lift" .
REMOVAL
Remove the engine and the transaxle assembly from the vehicle downward. Separate the engine and the tran-
saxle.
1. Remove engine undercover
2. Drain engine coolant from radiator. Refer to CO-8, "
Changing Engine Coolant" .
CAUTION:

Perform this step when the engine is cold.

Do not spill engine coolant on drive belt.
3. Remove front fender protector (RH and LH); Refer to EI-22, "
FENDER PROTECTOR" .
4. Remove exhaust front tube; Refer to EX-3, "
EXHAUST SYSTEM" .
5. Remove drive shafts (LH and RH) from steering knuckle. Refer to FAX-8, "
FRONT DRIVE SHAFT" .
6. Remove transaxle joint bolts which pierce at oil pan (upper) lower rear side. Refer to AT - 2 5 3 , "
TRAN-
SAXLE ASSEMBLY" (A/T models), CVT-207, "TRANSAXLE ASSEMBLY" (CVT) or MT-15, "TRAN-
SAXLE ASSEMBLY" (M/T models).
7. Remove rear torque rod (1).
NOTE:
A/T model shown CVT and M/T models similar.
8. Remove hood assembly. Refer to BL-14, "
HOOD" .
9. Remove cowl top cover and cowl top extension assembly. Refer to EI-20, "
COWL TOP" .
10. Release fuel pressure. Refer to EC-81, "
FUEL PRESSURE RELEASE" .
11. Remove battery and battery tray; Refer to SC-4, "
BATTERY" .
12. Remove drive belt; Refer to EM-13, "
Components" .
13. Remove air duct and air cleaner case assembly; Refer to EM-16, "
AIR CLEANER AND AIR DUCT" .
14. Remove cooling fan assembly.
15. Remove radiator hose (upper and lower). Refer to CO-11, "
RADIATOR" .
16. Disconnect A/T, CVT fluid cooler hoses. Refer to CO-11, "
RADIATOR"
17. Disconnect all connections of engine harness around the engine mounting insulator (LH), and then tem-
porarily secure the engine harness into the engine side.
CAUTION:
Protect connectors using a resin bag to protect against foreign materials during the operation.
18. Disconnect fuel feed hose at engine side. Refer to EM-33, "
Components" .
19. Disconnect heater hoses, and install plugs them to prevent engine coolant from draining. Refer to CO-20,
"Components" .
20. Disconnect control cable from transaxle. Refer to CVT-191, "
SHIFT CONTROL SYSTEM" (CVT) or AT -
229, "SHIFT CONTROL SYSTEM" (A/T), MT-12, "CONTROL LINKAGE" (MT).
21. Remove ground cable at transaxle side.
22. Remove ground cable between front cover and vehicle.
23. Remove alternator. Refer to SC-24, "
CHARGING SYSTEM" .
LBIA0460E

EM-76Revision: June 2006
ENGINE ASSEMBLY
2007 Versa
INSTALLATION
Note the following, and install in the reverse order of removal.

Do not allow engine oil to get on engine mounting insulator. Be careful not to damage engine mounting
insulator.

When installation directions are specified, install parts according to the directions. Refer to EM-73, "Com-
ponents" .

Make sure that each mounting insulator is seated properly, and tighten nuts and bolts.

Tighten engine mounting insulator (RH) bolts in the numerical
order shown.
INSPECTION AFTER INSTALLATION
Inspection for Leaks
The following are procedures for checking fluids leak, lubricates leak and exhaust gases leak.

Before starting engine, check oil/fluid levels including engine coolant and engine oil. If less than required
quantity, fill to the specified level. Refer to MA-11, "
RECOMMENDED FLUIDS AND LUBRICANTS" .

Use procedure below to check for fuel leakage.
–Turn ignition switch “ON” (with engine stopped). With fuel pressure applied to fuel piping, check for fuel
leakage at connection points.
–Start engine. With engine speed increased, check again for fuel leakage at connection points.

Run engine to check for unusual noise and vibration.

Warm up engine thoroughly to make sure there is no leakage of fuel, exhaust gases, or any oil/fluids
including engine oil and engine coolant.

Bleed air from lines and hoses of applicable lines, such as in cooling system.

After cooling down engine, again check oil/fluid levels including engine oil and engine coolant. Refill to the
specified level, if necessary.
Summary of the inspection items:
* Transmission/transaxle/CVT fluid, power steering fluid, brake fluid, etc.: Vehicle front
WBIA0785E
Item Before starting engine Engine running After engine stopped
Engine coolant Level Leakage Level
Engine oil Level Leakage Level
Other oils and fluid* Level Leakage Level
Fuel Leakage Leakage Leakage
Exhaust gases — Leakage —

EM-78Revision: June 2006
CYLINDER BLOCK
2007 Versa
Disassembly and AssemblyEBS00U7X
DISASSEMBLY
1. Remove engine and transaxle assembly from vehicle, separate transaxle from engine. Refer to EM-73,
"ENGINE ASSEMBLY" .
2. Install engine to engine stand as follows;
a. Remove flywheel (M/T models) or drive plate (1) (A/T or CVT
models).

Secure flywheel (M/T models) or drive plate (A/T or CVT mod-
els) using Tool (A), and remove bolts.
CAUTION:
Be careful not to damage or scratch drive plate (A/T or CVT
models) and contact surface for clutch disc of flywheel (M/T
models).
NOTE:
Figure shows drive plate (A/T or CVT models)
b. Lift the engine with a hoist to install it onto widely use engine stand.
CAUTION:

Use the engine stand that has a load capacity [approximately 135 kg (298 lb) or more] large
enough for supporting the engine weight.

If the load capacity of stand is not adequate, remove the following parts beforehand to reduce the
potential risk of overturning stand.
–Exhaust manifold; Refer to EM-21, "EXHAUST MANIFOLD" .
–Rocker cover; Refer to EM-30, "IGNITION COIL, SPARK PLUG AND ROCKER COVER" .
NOTE:
The figure shows an example of widely used engine stand (A)
that can support mating surface of transaxle with flywheel (M/T
models) or drive plate (A/T or CVT models) removed.
CAUTION:
Before removing the hanging chains, make sure the engine
stand is stable and there is no risk of overturning.
3. Remove oil pan (upper and lower). Refer to EM-24, "
OIL PAN" .
4. Remove cylinder head. Refer to EM-62, "
CYLINDER HEAD" .
5. Remove thermostat housing. Refer to CO-18, "
THERMOSTAT" .
1. Cylinder block 2. O-ring 3. Crankshaft position sensor (POS)
4.Crankshaft position sensor (POS)
cover5.Oil filter (for intake valve timing con-
trol)6. Knock sensor
7. Oil pressure switch 8. Top ring 9. Second ring
10. Oil ring 11. Snap ring 12. Piston
13. Piston pin 14. Connecting rod 15. Thrust bearing
16. Connecting rod bearing upper 17. Main bearing upper 18. Crankshaft key
19. Main bearing lower 20. Connecting rod bearing lower 21. Connecting rod bearing cap
22. Connecting rod bolt 23. Main bearing cap 24. Main bearing cap bolt
25. Crankshaft 26. Pilot converter (A/T or CVT models) 27. Signal plate
28. Rear oil seal 29. Drive plate (A/T or CVT models) 30. Reinforcement plate (A/T or CVT
models)
31. Flywheel (M/T models) 32. Block heater (Canada only) A. Refer to EM-81
Tool number : KV 11105210 (J-44716)
PBIC3226J
PBIC3227J

IDX-4
ALPHABETICAL INDEX
EC-398, EC-406
EVAP control system pressure sensor .... EC-382, EC-
385, EC-391
EVAP control system purge flow monitoring diagnosis
EC-340
EVAP vapor lines inspection ............................. MA-19
Evaporative emission (EVAP) system ............... EC-31
Evaporator ...................................................... MTC-90
Exhaust manifold .............................................. EM-21
Exhaust system inspection ................... MA-20, MA-22
Expansion valve .............................................. MTC-91
F
F/FOG - Wiring diagram ..................................... LT-43
F/PUMP - Wiring diagram ................................ EC-571
Final drive (FF M/T) ........................................... MT-22
Floor trim ............................................................. EI-37
Flow charts ......................................................... GI-27
Fluid temparature sensor (CVT) ...................... CVT-85
Fluid temperature sensor (A/T) ........................ AT-106
Fluids ................................................................ MA-11
Fluorescent leak detector ............................... MTC-92
Flywheel (clutch) ................................................ CL-13
Flywheel runout .............................................. EM-103
Fork rod (M/T) .................................................... MT-21
Freeze frame data ............................... EC-52, EC-116
Front bumper ...................................................... EI-14
Front door ......................................................... GW-43
Front passenger air bag .................................. SRS-46
Front seat belt ...................................................... SB-3
Front seat belt pre-tensioner ..... SB-2, SRS-3, SRS-51
Front washer ...................................................... WW-4
Front wiper ......................................................... WW-4
FTS - Wiring diagram ......................... AT-103, CVT-86
FTTS - Wiring diagram ...................... EC-293, EC-298
FUEL - Wiring diagram ...................... EC-278, EC-286
Fuel cut control (at no load high engine speed) . EC-26
Fuel gauge ............................................................ DI-5
Fuel injection system ......................... EC-276, EC-284
Fuel injector ..................................................... EC-564
Fuel injector and fuel tube ................................ EM-33
Fuel level sensor ................. EC-415, EC-417, EC-419
Fuel line inspection .................................. FL-4, MA-15
Fuel precautions ................................................... GI-6
Fuel pressure check .......................................... EC-81
Fuel pressure release ........................................ EC-81
Fuel pump ........................................................ EC-570
Fuel systemCommercial Service Tools ................ FL-3
Fuel systemPREPARATION ................................. FL-3
Fuel tank temperature sensor ............ EC-291, EC-297
Fuel tank vacuum relief valve ............................ EC-34
Fuse ................................................................... PG-16
Fuse and fusible link box ................................... PG-77
Fusible link ......................................................... PG-16
G
Gauges ................................................................. DI-5
Gear components (M/T) .................................... MT-18
Generic scan tool (GST) ................................. EC-126
Glass ...................................... GW-11, GW-43, GW-47
Grille - See Exterior ............................................. EI-19
Ground distribution ............................................ PG-30
H
H/LAMP - Wiring diagram .................................... LT-8
H/PHON - Wiring diagram .................................. AV-52
Handling precautions for plastics ..................... BL-255
Harness connector ............................................ PG-68
Harness layout .................................................. PG-39
Hazard warning lamp ......................................... LT-51
Headlining - See Roof trim .................................. EI-39
Heated oxygen sensor 2 ..... EC-248, EC-257, EC-267
Heated oxygen sensor 2 heater ...................... EC-166
HEATER - Wiring diagram .............................. MTC-28
Heater system - Wiring diagram ..................... MTC-28
HFC134a (R134a) system precaution .............. MTC-4
HFC134a (R134a) system service procedure . MTC-80
HFC134a (R134a) system service tools ......... MTC-12
HFC134a system service equipment precaution MTC-9
HO2S2 - Wiring diagram ..... EC-251, EC-260, EC-270
HO2S2H - Wiring diagram .............................. EC-168
Horn ................................................................. WW-46
HORN - Wiring diagram ................................... WW-46
How to erase DTC for OBD system .................. EC-60
I
IATS - Wiring diagram ..................................... EC-197
Idle air volume learning ..................................... EC-78
Idle speed ......................................................... EC-75
Idle speed control (ISC) .................... EC-423, EC-425
Ignition coil ...................................................... EC-576
Ignition control system .................................... EC-576
Ignition timing .................................................... EC-75
IGNSYS - Wiring diagram ............................... EC-577
ILL - Wiring diagram ......................................... LT-111
Illumination control ........................................... LT-108
In-cabin Microfilter ............................................. MA-20
INJECT - Wiring diagram ................................ EC-565
Input shaft (FF M/T) .......................................... MT-18
Input/Output signal of TCM ............................. CVT-25
Instrument panel ................................................. IP-10
INT/L - Wiring diagram ....................................... LT-96
Intake air temperature sensor ........... EC-195, EC-215
Intake door control linkage adjustment ........... MTC-69
Intake manifold .................................................. EM-18
Intake valve timing control .............................. EC-156
Intake valve timing control solenoid valve ....... EC-173
Interior ................................................................. EI-32
Interior lamp ....................................................... LT-91
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-17
IVC - Wiring diagram ....................................... EC-174

IDX-5
A
C
D
E
F
G
H
I
J
K
L B
IDX
ALPHABETICAL INDEX
K
KEYLES - Wiring diagram .................................. BL-57
Knock sensor (KS) .......................................... EC-315
KS - Wiring diagram ........................................ EC-316
L
L/USSV - Wiring diagram .............................. CVT-159
Line pressure and secondary pressure control CVT-26
Line pressure solenoid valve ......... CVT-113, CVT-118
Line pressure test (A/T) ...................................... AT-56
Liquid gasket application ................ EM-5, LU-2, CO-3
Location of electrical units ................................. PG-64
Lock-up and select control .............................. CVT-28
Lock-up select solenoid valve ....................... CVT-158
Low tire pressure warning system ....................... WT-7
Low tire pressure warning system - trouble diagnoses
WT-10
Low tire pressure warning system - Wiring diagram ....
WT-10
LPSV - Wiring diagram .................... AT-146, CVT-114
Lubricant (R134a) A/C ...................... MTC-5, MTC-18
Lubrication circuit (engine) ................................... LU-4
Lubrication oil A/C .......................................... MTC-96
M
M/T major overhaul ........................................... MT-17
M/T removal and installation ............................. MT-15
MAFS - Wiring diagram ..................... EC-181, EC-189
Magnet clutch ................................................. MTC-41
MAIN - Wiring diagram ...................... EC-144, AT-183
Mainshaft (M/T) ................................................. MT-18
Maintenance ........................................................ MA-5
Malfunction indicator lamp (MIL) ....................... EC-61
Manual air conditioner - Wiring diagram ........ MTC-29
Mass air flow sensor (MAFS) ............ EC-178, EC-187
Master cylinder (clutch) ........................................ CL-9
Meter ..................................................................... DI-5
METER - Wiring diagram ...................................... DI-9
MIL data link connectors circuit ....................... EC-592
MIRROR - Wiring diagram ............................... GW-64
Mirror, door ....................................................... GW-65
Mirror, out side ................................................. GW-65
Misfire .............................................................. EC-308
Mode door control linkage adjustment ........... MTC-71
Molding - See Exterior .............................. EI-23, EI-24
Mud guard - See Exterior .................................... EI-26
Multiport fuel injection (MFI) system ................. EC-23
Multiport fuel injection precautions ....................... GI-6
Multi-remote control system - See Remote keyless entry
system ................................................................ BL-54
N
NATS - Wiring diagram .................................... BL-215
NATS (Nissan anti-theft system) precautions ...... GI-3
NONDTC - Wiring diagram ............. AT-193, CVT-176
NVH troubleshooting (BR) ................................... BR-5
NVH troubleshooting (RSU) ............................. RSU-4
NVIS (Nissan vehicle immobilizer system) ....... BL-212
O
Oil change (capacity) ......................................... MA-11
Oil cooler (engine) ............................................. EM-24
Oil filter ................................................................ LU-8
Oil pan (engine) ................................................. EM-24
Oil pressure (engine) ........................................... LU-5
Oil seal replacement (engine) . EM-24, EM-37, EM-59,
EM-66
On board diagnostic system .............................. EC-47
ORVR (On-board Refueling Vapor Recovery) ... EC-38
Out side mirror .................................................. GW-65
Overdrive control switch ..................... AT-186, AT-191
Overheat .......................................................... EC-443
OVRCSV - Wiring diagram .............................. AT-162
P
P/SCKT - Wiring diagram ................................ WW-44
Park/Neutral position switch ............................ EC-436
Park/neutral position switch (A/T) ......... AT-97, AT-186
Park/neutral position switch (CVT) .................. CVT-78
Park/neutral position switch (M/T) ..................... MT-11
Parking brake control ........................................... PB-4
PCV (positive crankcase ventilation) ................. EC-44
Periodic maintenance .......................................... MA-7
PGC/V - Wiring diagram .................... EC-356, EC-364
PHASE - Wiring diagram ................................. EC-329
Pilot bushing replacement ................................. EM-77
Piston assembly ................................................ EM-99
Piston pin inspection .......................................... EM-95
Piston ring inspection ........................................ EM-96
Piston to bore clearance .................................... EM-99
PNP/SW - Wiring diagram ..... EC-438, AT-98, CVT-80
POS - Wiring diagram ...................................... EC-321
POWER - Wiring diagram ................... CVT-146, PG-6
Power door lock .................................................. BL-23
Power socket ................................................... WW-44
Power steering gear .......................................... PS-12
Power supply routing ........................................... PG-4
Power window .................................................. GW-17
PRE/SE - Wiring diagram .................. EC-387, EC-393
Precations for Leak detection dye .................. MTC-10
Precautions (General) .......................................... GI-4
Pressure control solenoid valve A CVT-113, CVT-118
Pressure control solenoid valve B CVT-121, CVT-124
Pressure plate - See Clutch cover ..................... CL-13
Pressure test (CVT) ......................................... CVT-45
Primary pressure sensor ............................... CVT-137
Primary Speed Sensor .................................... CVT-90
PRIPS - Wiring diagram ................................ CVT-138
PRSCVT - Wiring diagram ............................... CVT-91
PT/SEN - Wiring diagram ................................ AT-177

TROUBLE DIAGNOSIS
LAN-49
[CAN]
C
D
E
F
G
H
I
J
L
MA
B
LAN
Revision: June 20062007 Versa
*1: Models with Intelligent Key system
*2: Models with ABS
*3: Models with air conditioner
*4: Models for Canada
*5: Models for USA
NOTE:
CAN data of the air bag diagnosis sensor unit is not used by usual service work, thus it is omitted.
TYPE 5/TYPE 6
NOTE:
Refer to LAN-41, "
Abbreviation List" for the abbreviations of the connecting units.
T: Transmit R: Receive Sleep/wake up signalRT
TRRR
Vehicle speed signalRRR T
RRRT
ABS warning lamp signalRT
Brake warning lamp signalRT
Front wiper stop position signal R T
High beam status signal RT
Low beam status signal RT
Oil pressure switch signalRT
Rear window defogger control signal RT Signals ECM BCM EPS
I-KEY
*1M&A
ABS*2IPDM-E
Signals ECM BCM EPS M&A
ABS*1TCM IPDM-E
A/C compressor request signal
*2TR
Accelerator pedal position signal T R
ASCD CRUISE lamp signal T R
ASCD SET lamp signal T R
Closed throttle position signal T R
Cooling fan motor operation signal TR
Engine coolant temperature signal T R
Engine speed signal T R
Engine status signal T R
Fuel consumption monitor signal T R
Malfunction indicator lamp signal T R
Wide open throttle position signal T R
A/C switch signal
*2RT
Blower fan motor switch signal R T
Buzzer output signalTR
R
Day time running light request signal
*3TR
Door switch signal T R R
Front wiper request signal T R
High beam request signal T R R
Horn chirp signal T R
Ignition switch signal T R

LAN-50
[CAN]
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
*1: Models with ABS
*2: Models with air conditioner
*3: Models for Canada
*4: Models for USA
NOTE:
CAN data of the air bag diagnosis sensor unit is not used by usual service work, thus it is omitted.
TYPE 7/TYPE 8/TYPE 9/TYPE 10
NOTE:
Refer to LAN-41, "
Abbreviation List" for the abbreviations of the connecting units.
T: Transmit R: Receive Low beam request signal T R
Position lights request signal T R R
Rear window defogger switch signal T R
Theft warning horn request signal T R
Tire pressure signal
*4TR
Turn indicator signal T R
EPS operation signal R T
EPS warning lamp signal T R
Fuel level sensor signal R T
Overdrive control switch signal T R
P/N range signal T R
Sleep/wake up signalRT
TR R
Stop lamp switch signal T R
Vehicle speed signalRRR T
RRRT
ABS warning lamp signal R T
Brake warning lamp signal R T
A/T check indicator signal R T
A/T self-diagnosis signal R T
OD OFF indicator signal R T
Output shaft revolution signal R T
Shift position signal R T
Turbine revolution signal R T
Front wiper stop position signal R T
High beam status signal RT
Low beam status signal RT
Oil pressure switch signal R T
Rear window defogger control signal RT Signals ECM BCM EPS M&A
ABS
*1TCM IPDM-E
Signals ECM BCM EPS
I-KEY*1M&A
ABS*2TCM IPDM-E
A/C compressor request signal TR
Accelerator pedal position signal T R
ASCD CRUISE lamp signal T R
ASCD SET lamp signal T R
Closed throttle position signal T R

LAN-52
[CAN]
TROUBLE DIAGNOSIS
Revision: June 20062007 Versa
*1: Models with Intelligent Key system
*2: Models with ABS
*3: Models for Canada
*4: Models for USA
*5: Models without ABS
NOTE:
CAN data of the air bag diagnosis sensor unit is not used by usual service work, thus it is omitted.
Input shaft revolution signal R T
Output shaft revolution signal R T
Shift position indicator signal R T
OD OFF indicator signal R T
Front wiper stop position signal R T
High beam status signal RT
Low beam status signal RT
Oil pressure switch signal R T
Rear window defogger control signal RT Signals ECM BCM EPS
I-KEY
*1M&A
ABS*2TCM IPDM-E

HEADLAMP (FOR USA)
LT-23
C
D
E
F
G
H
I
J
L
MA
B
LT
Revision: June 20062007 Versa
3. CHECKING CAN COMMUNICATIONS BETWEEN BCM AND IPDM E/R
Select “BCM” on CONSULT-II, and perform self-diagnosis for
“BCM”.
Display of self
-diagnosis results
NO DTC>> Replace IPDM E/R. Refer to PG-29, "Removal and
Installation of IPDM E/R" .
CAN COMM CIRCUIT>> Refer to LAN-44, "
TROUBLE DIAGNO-
SIS" .
Aiming AdjustmentEKS00IMG
PREPARATION BEFORE ADJUSTING
Before performing aiming adjustment, check the following.
1. Keep all tires inflated to correct pressures.
2. Place vehicle on level surface.
3. Set that there is no-load in vehicle other than the driver (or equivalent weight placed in driver's position).
Coolant, engine oil filled up to correct level and full fuel tank.
LOW BEAM AND HIGH BEAM
1. Turn headlamp low beam ON.
2. Use adjusting screw to perform aiming adjustment.
PKIA7627E
1. Headlamp A. Inner and outer adjustment B. Adjusting screw
WKIA5417E