engine NISSAN TIIDA 2007 Service Repair Manual

IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
SEC-73
< ECU DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE
ROOM)
Reference ValueINFOID:0000000001404135
Refer to IPDM E/R.
Fail SafeINFOID:0000000001404139
CAN communication control
When CAN communication with ECM and BCM is impossible, IPDM E/R performs fail-safe control. After CAN
communication recovers normally, it also returns to normal control.
If no CAN communication is available with ECM
*1: HR engine models
*2: MR engine and K9K engine models
If no CAN communication is available with BCM
Ignition relay malfunction detection function
 IPDM E/R monitors the voltage at the contact circuit and excitation coil circuit of the ignition relay inside it.
 IPDM E/R judges the ignition relay error if the voltage differs between the contact circuit and the excitation
coil circuit.
 If the ignition relay cannot turn OFF due to contact seizure, it activates the tail lamp relay for 10 minutes to
alert the user to the ignition relay malfunction when the ignition switch is turned OFF.
Control part Fail-safe in operation
Cooling fan The cooling fan relay-2*
1 or the cooling fan relay-3*2 turns ON when the ignition switch
is turned ON
 Turns off the fan motor low relay when the ignition switch is turned OFF
A/C compressor A/C relay OFF
Control part Fail-safe in operation
Headlamp The headlamp low relay turns ON when the ignition switch is turned ON
 The headlamp low relay turns OFF when the ignition switch is turned OFF
 Headlamp high relay OFF
Parking lamps
 License plate lamps
 Tail lamps
 Illuminations The tail lamp relay turns ON when the ignition switch is turned ON
 The tail lamp relay turns OFF when the ignition switch is turned OFF
Front wiper The status just before activation of fail-safe control is maintained until the ignition
switch is turned OFF while the front wiper is operating at LO or HI speed.
 The front wiper is operated at LO speed until the ignition switch is turned OFF if the
fail-safe control is activated while the front wiper is set in the INT mode and the front
wiper motor is operating.
Front fog lamps Front fog lamp relay OFF
Starter motor Inhibit relay OFF
Rear window defogger Rear window defogger relay OFF
Headlamp washer Headlamp washer relay OFF
PTC heater PTC heater relay OFF
DTC Ignition switch Ignition relay Tail lamp relay
—ONON—
—OFFOFF—
B2098: IGN RLY ON OFF ON ON (10 minutes)
B2099: IGN RLY OFF ON OFF —

SEC-74
< ECU DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM)
NOTE:
The tail lamp relay is turned OFF when the ignition switch is turned ON.
Front wiper control
IPDM E/R detects the front wiper stop position with the front wiper auto stop signal.
When the front wiper auto stop signal is in the conditions listed below, IPDM E/R repeats a front wiper 10 sec-
onds operation and 20 seconds stop five times.
NOTE:
This operation status can be confirmed on the IPDM E/R “Data Monitor” that displays “BLOCK” for the item
“WIP PROT” while the wiper is stopped.
DTC IndexINFOID:0000000001404140
NOTE:
The details of time display are as follows.
 CRNT: The malfunctions that are detected now.
 PAST: The number is indicated when it is normal at present and a malfunction was detected in the past.Ignition switch Front wiper switch Front wiper auto stop signal
ONOFFThe front wiper auto stop signal (stop posi-
tion) cannot be input for 10 seconds.
ONThe front wiper auto stop signal does not
change for 10 seconds.
CONSULT display Fail-safe
TimingNOTEReference page
No DTC is detected.
further testing
may be required.————
U1000: CAN COMM CIRCUIT×CRNT PASTXX-XX, "*****"
B2098: IGN RELAY ON×CRNT PASTXX-XX, "*****"
B2099: IGN RELAY OFF — CRNT PASTXX-XX, "*****"
B2100: EEPROM — CRNT PASTXX-XX, "*****"

INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION SYMPTOMS
SEC-75
< SYMPTOM DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
SYMPTOM DIAGNOSIS
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION SYMPTOMS
Symptom TableINFOID:0000000001404141
NOTE:
 Before performing the diagnosis in the following table, check “XX-XX, "*****"
”.
 Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
 If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
 Engine start function is ON when setting on CONSULT-III.
 Mechanical key is not inserted in key cylinder.
 One or more of Intelligent Keys with registered Intelligent Key ID is in the vehicle.
Symptom Diagnosis/service procedureReference
page
Ignition switch does not turn on with Intelligent Key.
[KEY warning lamp (green) illuminates.]1. Check steering lock unit.SEC-23
2. Replace Intelligent Key unit.XX-XX, "*****"
Ignition switch does not turn on with Intelligent Key.
[KEY warning lamp does not illuminate.]1.Check Intelligent Key unit power supply and ground cir-
cuit.XX-XX,
"*****"
2. Check ignition knob switch.XX-XX, "*****"
3. Check key switch.XX-XX, "*****"
4. Replace Intelligent Key unit.XX-XX, "*****"
Ignition switch does not turn on with Intelligent Key.
[KEY warning lamp (red) illuminates.]1. Check inside key antenna.XX-XX, "*****"
2. Replace Intelligent Key unit.XX-XX, "*****"
Ignition switch does not turn on with mechanical key Check key switch.XX-XX, "*****"
Engine cannot start1. Check key switch.XX-XX,
"*****"
2. Check stop lamp switch (A/T).XX-XX, "*****"
3. Check stop lamp switch (M/T).XX-XX, "*****"

SEC-76
< SYMPTOM DIAGNOSIS >[WITH INTELLIGENT KEY SYSTEM]
NATS (NISSAN ANTI-THEFT SYSTEM) SYMPTOMS
NATS (NISSAN ANTI-THEFT SYSTEM) SYMPTOMS
Symptom TableINFOID:0000000001404143
NOTE:
 Before performing the diagnosis in the following table, check “SEC-4, "
Work Flow"”.
 Check that vehicle is under the condition shown in “Conditions of vehicle” before starting diagnosis, and
check each symptom.
 If the following symptoms are detected, check systems shown in the “Diagnosis/service procedure” column
in this order.
CONDITIONS OF VEHICLE (OPERATING CONDITIONS)
 Mechanical key is not inserted into key cylinder.
 Ignition knob switch is not depressed.
Symptom Diagnosis/service procedure Reference page
Engine cannot start.1. Check stop lamp switchXX-XX, "*****"
2. Check Intermittent IncidentXX-XX, "*****"
Security indicator does not turn ON or flash.1. Check vehicle security indicatorSEC-492. Check Intermittent IncidentXX-XX, "*****"

PRE-INSPECTION FOR DIAGNOSTIC
SEC-77
< ON-VEHICLE MAINTENANCE >[WITH INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
ON-VEHICLE MAINTENANCE
PRE-INSPECTION FOR DIAGNOSTIC
Basic InspectionINFOID:0000000001404144
The engine start function, door lock function, and NATS in the Intelligent Key system are closely related to
each other regarding control. Narrow down the functional area in question by performing basic inspection to
identify which function is malfunctioning. The vehicle security function can operate only when the door lock is
operating normally. Therefore, it is easy to identify any factor unique to the vehicle security system by perform-
ing the vehicle security operation check after basic inspection.
1.CHECK DOOR LOCK OPERATION
Check the door lock for normal operation with the Intelligent Key and door request switch.
Successful door lock operation with the Intelligent Key and request switch indicates that the remote keyless
entry receiver and inside key antenna required for engine start are functioning normally.
Identify the malfunctioning point by referring to the DLK section if the door cannot be unlocked.
Can the door be locked with the Intelligent Key and door request switch?
YES >> GO TO 2.
NO >> Refer to XX-XX, "*****"
.
2.CHECK IGNITION KNOB SWITCH OPERATION-1
With all registered Intelligent Keys, check if ignition knob can rotate when carrying Intelligent Key inside the
vehicle.
Does ignition knob rotate?
YES >> GO TO 3.
NO >> Refer to SEC-76, "
Symptom Table".
3.CHECK IGNITION KNOB SWITCH OPERATION-2
Insert registered mechanical key into key cylinder, and check if ignition knob can rotate. Check for all regis-
tered mechanical keys.
Does ignition knob rotate?
YES >> GO TO 4.
NO (Does not rotate with some of mechanical keys)>>Perform mechanical key registration.
NO (Does not rotate with all mechanical keys)>>Refer to SEC-76, "
Symptom Table".
4.CHECK VEHICLE SECURITY SYSTEM
Check the vehicle security system for normal operation.
The vehicle security function can operate only when the door lock function is operating normally.
Therefore, it is easy to identify any factor unique to the vehicle security by performing the vehicle security
operation check after this basic inspection.
>> Go to SEC-77, "
Vehicle Security Operation Check".
Vehicle Security Operation CheckINFOID:0000000001404145
1.INSPECTION START
Turn ignition switch “OFF” and pull out mechanical key from key cylinder.
NOTE:
Before starting operation check, open front windows.
>> GO TO 2.
2.CHECK SECURITY INDICATOR LAMP
1. Lock doors using Intelligent Key.
2. Check that security indicator lamp illuminates for 30 seconds.
Security indicator lamp should illuminate.
OK >> GO TO 3.

INSPECTION AND ADJUSTMENT
SEC-83
< BASIC INSPECTION >[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000001404154
Refer to the CONSULT-III Operation Manual-NATS.
ECM RE-COMMUNICATING FUNCTION
ECM RE-COMMUNICATING FUNCTION : DescriptionINFOID:0000000001404155
Performing following procedure can automatically perform re-communication of ECM and BCM, but only when
the ECM has been replaced with a new one (*1).
*1: New one means an ECM which has never been energized on-board.
(In this step, initialization procedure by CONSULT-III is not necessary)
NOTE:
When registering new Key IDs or replacing the ECM that is not brand new, refer to CONSULT-III Oper-
ation Manual.
If multiple keys are attached to the key holder, separate them before work.
Distinguish keys with unregistered key ID from those with registered ID.
ECM RE-COMMUNICATING FUNCTION : Special Repair RequirementINFOID:0000000001404156
1.PERFORM ECM RE-COMMUNICATING FUNCTION
1. Install ECM.
2. Using a registered key (*2), turn ignition switch to “ON”.
*2: To perform this step, use the key that has been used before performing ECM replacement.
3. Maintain ignition switch in “ON” position for at least 5 seconds.
4. Turn ignition switch to “OFF”.
5. Start engine.
Can engine be started?
YES >> Procedure is completed.
NO >> Initialize control unit. Refer to CONSULT-III Operation Manual NATS.

SEC-84
< FUNCTION DIAGNOSIS >[WITHOUT INTELLIGENT KEY SYSTEM]
NATS (NISSAN ANTI-THEFT SYSTEM)
FUNCTION DIAGNOSIS
NATS (NISSAN ANTI-THEFT SYSTEM)
System DiagramINFOID:0000000001404157
System DescriptionINFOID:0000000001404158
INPUT/OUTPUT SIGNAL CHART
BCM
SYSTEM DESCRIPTION
NATS (Nissan Anti-Theft System) has the following immobilizer functions:
 Engine immobilizer shows high anti-theft performance to prevent engine start by other than the owner.
 Only a key with key ID registered in BCM and ECM can start engine, and shows high anti-theft performance
to prevent key from being copied or stolen.
 Security indicator always flashes with mechanical key removed condition (key switch: OFF).
 Therefore, NATS warns outsiders that the vehicle is equipped with the anti-theft system. Refer to XX-XX,
"*****".
 If system detects malfunction, security indicator illuminate when ignition switch is turned to ON position.
 If the owner requires, ignition key ID can be registered for up to 5 keys.
 During trouble diagnosis or when the following parts have been replaced, and if ignition key is added, regis-
tration* is required.
*1: All keys kept by the owner of the vehicle should be registered with ignition key.
-ECM
-BCM
- Ignition key
- ABS actuator control unit
- EPS sontrol unit
- IPDM E/R
- Combination meter
 NATS trouble diagnosis, system initialization and additional registration of other Ignition key IDs must be car-
ried out using CONSULT-III hardware and SECURITY CARD.
When NATS initialization has been completed, the ID of the inserted ignition key or ignition key IDs can be
carried out.
PIIA1121E
Switch/Input signal Input signal to BCM BCM function Actuator/Output signal
NATS antenna amp. Key ID
NATS Security indicator lamp
 Starter request
ECM Engine status signal

NATS (NISSAN ANTI-THEFT SYSTEM)
SEC-85
< FUNCTION DIAGNOSIS >[WITHOUT INTELLIGENT KEY SYSTEM]
C
D
E
F
G
H
I
J
L
MA
B
SEC
N
O
P
 Possible symptom of NATS malfunction is “Engine cannot start” In J10, the engine can be started with the
NATS. Identify the possible causes according to “Work Flow”. Refer to SEC-80, "
Work Flow".
 If ECM other than Genuine NISSAN is installed, the engine cannot be started. For ECM replacement proce-
dure, refer to SEC-83, "
ECM RE-COMMUNICATING FUNCTION : Description".
PRECAUTIONS FOR KEY REGISTRATION
 The key registration is a procedure that erases the current NATS ID once, and then re-registers a new ID.
Therefore the registered ignition key is necessary for this procedure. Before starting the registration opera-
tion collect all registered ignition keys from the customer
 The NATS ID registration is the procedure that registers the ID stored into the transponder (integrated in
ignition key) to BCM.
SECURITY INDICATOR
 Security indicator blinks when the ignition switch is in “OFF” or “ACC” position.
 When NATS detects trouble, the security indicator lamp lights up while ignition key is in the “ON” position.
MAINTENANCE INFORMATION
CAUTION:
If necessary to perform NATS ID registration when replacing any of the following part.
If it's not (or fail to do so), the electrical system may not operate properly.
 BCM
ECM
 IPDM E/R
 Ignition key
 NATS antenna amp.
Component Parts LocationINFOID:0000000001404159
1. BCM M18, M20
(view with glove box removed)2. NATS antenna amp. M21 3. Security indicator lamp M31
4. ECM E16
ALKIA0849ZZ

SEC-92
< COMPONENT DIAGNOSIS >[WITHOUT INTELLIGENT KEY SYSTEM]
B2190, P1614 NATS ANTENNA AMP.
B2190, P1614 NATS ANTENNA AMP.
DescriptionINFOID:0000000001532070
Performs ID verification through BCM and NATS antenna amplifier when ignition knob switch is pressed.
Prohibits the start of engine when an unregistered ID of mechanical key is used.
DTC LogicINFOID:0000000001532071
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Insert ignition key into the key cylinder.
2. Turn ignition switch ON.
3. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to XX-XX, "*****".
NO >> INSPECTION END.
Diagnosis ProcedureINFOID:0000000001532072
1.CHECK NATS ANTENNA AMP. INSTALLATION
Check NATS antenna amp. installation. Refer to XX-XX, "*****"
.
Is the inspection result normal?
YES >> GO TO 2.
NO >> Reinstall NATS antenna amp. correctly.
2.CHECK NATS IGNITION KEY ID CHIP
Start engine with another registered NATS ignition key.
Does the engine start?
YES >>  Ignition key ID chip is malfunctioning.
 Replace the ignition key.
 Perform initialization with CONSULT-III.
For initialization, refer to “CONSULT-III Operation Manual”.
NO >> GO TO 3.
3.CHECK POWER SUPPLY FOR NATS ANTENNA AMP.
1. Turn ignition switch ON.
2. Check voltage between NATS antenna amp. connector M21 terminal 3 and ground.
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B2190
NATS ANTENNA
AMP Inactive communication between NATS antenna
amp. and BCM.
 Mechanical key is malfunctioning. Harness or connectors
(The NATS antenna amp. circuit is
open or shorted)
 Mechanical key
 NATS antenna amp.
BCM P1614

SEC-94
< COMPONENT DIAGNOSIS >[WITHOUT INTELLIGENT KEY SYSTEM]
B2191, P1615 DIFFERENCE OF KEY
B2191, P1615 DIFFERENCE OF KEY
DescriptionINFOID:0000000001404177
Performs ID verification through BCM when ignition switch is ON position.
Prohibits the release of steering lock or start of engine when an unregistered key is used.
DTC LogicINFOID:0000000001404178
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PERFORM DTC CONFIRMATION PROCEDURE
1. Insert ignition key into the key cylinder.
2. Press the ignition knob switch.
3. Check “Self diagnostic result” with CONSULT-III.
Is DTC detected?
YES >> Refer to SEC-94, "Diagnosis Procedure".
NO >> INSPECTION END.
Diagnosis ProcedureINFOID:0000000001404179
1.PERFORM INITIALIZATION
Perform initialization with CONSULT-III. Re-register all ignition keys.
For initialization and registration of ignition key. Refer to CONSULT-III Operation Manual.
Can the system be initialized and can the engine be started with re-registered ignition key?
YES >> Ignition key was unregistered.
NO >> BCM is malfunctioning.
 Replace BCM. Refer to XX-XX, "*****"
.
 Perform initialization again
DTC No.Trouble diagnosis
nameDTC detecting condition Possible cause
B2191
DIFFERENCE OF
KEYThe ID verification results between BCM and igni-
tion key are NG. The registration is necessary. Ignition key
P1615