display NISSAN TIIDA 2007 Service Owner's Manual

AV
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
AV-49
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
DATA MONITOR
Error item Description Possible cause/Action to take
CAN COMM CIRCUIT[U1000]CAN communication malfunction is de-
tected.Perform the diagnosis using CONSULT-III,
and then repair the malfunctioning parts
based on diagnostic results.
Refer to AV- 5 2 , "
DiagnosisProcedure".
CONTROL UNIT (CAN) [U1010] CAN initial diagnosis malfunction is de-
tected.NAVI control unit
CONTROL UNIT (AV) [U1310]AV communication circuit initial diagno-
sis malfunction is detected.NAVI control unit
 AV COMM CIRCUIT [U1300]
 SWITCH CONN [U1240]
 AUDIO H/U CONN [U1249]
 AMP CONN [U124E]
 RDS CONN [U124F] Audio unit power supply and ground
circuit malfunction is detected.
 Malfunction is detected on communi-
cation circuit between audio unit and
NAVI control unit.
 Malfunction is detected on communi-
cation signal between audio unit and
NAVI control unit. Audio unit power supply and ground cir-
cuit
 Communication circuit between audio
unit and NAVI control unit
FRONT DISP CONN [U1243] Display unit power supply and
ground circuit malfunction is detect-
ed.
 Malfunction is detected on communi-
cation circuit between display unit
and NAVI control unit.
 Malfunction is detected on communi-
cation signal between display unit
and NAVI control unit. Display unit power supply and ground
circuit
 Communication circuit between display
unit and NAVI control unit
GPS ANTENNA CONN [U1244]GPS antenna connection malfunction
is detected. GPS antenna feeder
 GPS antenna
Control Unit FLASH-ROM [U1200]NAVI control unit malfunction is detect-
ed.NAVI control unit
Gyro NO CONN [U1201]NAVI control unit malfunction is detect-
ed.NAVI control unit
GPS COMM [U1204]
GPS malfunction is detected.Intermittent malfunction caused by strong
radio interference may be detected if the
symptoms such as the GPS receipt mal-
function occur.
Replace NAVI control unit if the malfunc-
tion always occurs. GPS ROM [U1205]
GPS RAM [U1206]
GPS RTC [U1207]
DVD-ROM COMM [U1208]
 Malfunction is detected on DVD-
ROM drive pickup lens in NAVI con-
trol unit.
 There is dirt and damage on the map
disc.Map disc
NAVI control unit DVD-ROM READ [U1209]
DVD-ROM DISC [U120A]
DVD-ROM MECHA DETECT [U120C]
DVD-ROM DRIVE MECHA [U120D]
DVD-ROM FOCUS [U120E]
DVD-ROM TOC [U120F]
DVD-ROM SEEK [U1210]
DVD-ROM ERR CORRECTION [U1211]
DVD-ROM DATA FORWARD [U1212]
DVD-ROM DATA [U1213]
DVD-ROM TIMEOUT [U1214]
DVD-ROM LOAD [U1215]
CAN CONT [U1216]
NAVI control unit malfunction is detect-
ed.NAVI control unit
BLUETOOTH CONN [U1217]

AV-50
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
ALL SIGNALS
 Displays the status of the following vehicle signals inputted to the NAVI control unit.
 For each signal, actual signal can be compared with the condition recognized on the system.
SELECTION FROM MENU
Allows the technician to select which vehicle signals should be displayed and displays the status of the
selected vehicle signals.
AV communication monitor
AV&NAVI C/U
 Displays the communication status from NAVI control unit to each unit as well as the error counter.
 The error counter displays “OK” if no malfunction was detected in the past and displays “0” if a malfunction is
detected. It increases by 1 if the condition is normal at the next ignition switch ON cycle. The upper limit of
the counter is 39.
AUDIO
 Displays the NAVI control unit communication status and the error counter.
Display ItemDis-
playVehicle status Remarks
VHCL SPD SIGON Vehicle speed >0 km/h (0 MPH)
Changes in indication may be delayed. This is
normal.
OFF Vehicle speed =0 km/h (0 MPH)
PKB SIGON Parking brake is applied.
Changes in indication may be delayed. This is
normal.
OFF Parking brake is released.
ILLUM SIGON Lighting switch ON
—
OFF Lighting switch OFF
IGN SIGON Ignition switch ON
—
OFF Ignition switch in ACC position
REV SIGON Selector lever in R position
Changes in indication may be delayed. This is
normal.
OFFSelector lever in any position other
than R
Item to be selected Description
VHCL SPD SIG
The same as when “ALL SIGNALS”
is selected. PKB SIG
ILLUM SIG
IGN SIG
REV SIG
Items Display (Current)Malfunction
counter
(Past)
TRANSMIT DIAG OK / UNKWN OK / 0 – 39
PANEL SWITCH OK/ UNKWN OK / 0 – 39
SW SECONDARY — —
RR CONTROL SW — —
STEERING SW OK / UNKWN OK / 0 – 39
AUDIO OK / UNKWN OK / 0 – 39
SPEAKER AMP OK / UNKWN OK / 0 – 39
FM MULTI OK / UNKWN OK / 0 – 39

AV
DIAGNOSIS SYSTEM (NAVI CONTROL UNIT)
AV-51
< FUNCTION DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
 The error counter displays “OK” if no malfunction was detected in the past and displays “0” if a malfunction is
detected. It increases by 1 if the condition is normal at the next ignition switch ON cycle. The upper limit of
the counter is 39.
ECU PART NUMBER
The part number of NAVI control unit is displayed.
Items Display (Current)Malfunction
counter
(Past)
TRANSMIT DG OK / UNKWN OK / 0 – 39

AV-52
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
U1000 CAN COMM CIRCUIT
COMPONENT DIAGNOSIS
U1000 CAN COMM CIRCUIT
DescriptionINFOID:0000000001728646
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN-H line, CAN-L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication Signal Chart. Refer to XX-XX, "*****"
.
DTC LogicINFOID:0000000001728647
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000001728648
1.PERFORM SELF DIAGNOSTIC
1. Turn ignition switch ON and wait for 2 second or more.
2. Check “Self Diagnostic Result” of “MULTI AV”.
Is
“CAN COMM CIRCUIT” displayed?
YES >> Refer to “LAN system”. Refer to XX-XX, "*****".
NO >> Refer to GI section. Refer to XX-XX, "*****"
.
DTCDisplay contents of CON-
SULT-IIIDiagnostic item is detected when... Probable malfunction location
U1000CAN COMM CIRCUIT
[U1000]NAVI control unit does not transmit or receive
CAN communication signal for 2 seconds or
more.CAN communication system

AV
U1010 CONTROL UNIT (CAN)
AV-53
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
U1010 CONTROL UNIT (CAN)
DescriptionINFOID:0000000001728649
Initial diagnosis of NAVI control unit.
DTC LogicINFOID:0000000001728650
DTC DETECTION LOGIC
Diagnosis ProcedureINFOID:0000000001728651
1.REPLACE NAVI CONTROL UNIT
Replace NAVI control unit when DTC U1010 is detected.
>> INSPECTION END
DTCDisplay contents of CON-
SULT-IIIDiagnostic item is detected when... Probable malfunction location
U1010CONTROL UNIT (CAN)
[U1010]CAN initial diagnosis malfunction is detected. NAVI control unit

AV-54
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
U1310 NAVI CONTROL UNIT
U1310 NAVI CONTROL UNIT
DescriptionINFOID:0000000001728652
Replace the NAVI control unit if this DTC is displayed. Refer to XX-XX, "*****".
DTC LogicINFOID:0000000001728653
Part name Description
NAVI CONTORL UNIT Map data can be read from the map DVD-ROM by installing map DVD-ROM.
 It is the master unit of the MULTI AV system, and it is connected to each control
unit by means of communication. It operates each system according to com-
munication signals from the NAVI control unit.
 The NAVI control unit includes the audio, hands-free phone, navigation, and
vehicle information functions.
 It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
 It inputs the illumination signals that are required for the display dimming con-
trol.
 It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Action to take
U1310CONTROL UNIT (AV)
[U1310]An initial diagnosis error is detected in AV communication
circuit.Replace NAVI control unit.

AV
U1200 NAVI CONTROL UNIT
AV-55
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
U1200 NAVI CONTROL UNIT
DescriptionINFOID:0000000001728654
Replace the NAVI control unit if this DTC is displayed. Refer to XX-XX, "*****".
DTC LogicINFOID:0000000001728655
Part name Description
NAVI CONTORL UNIT Map data can be read from the map DVD-ROM by installing map DVD-ROM.
 It is the master unit of the MULTI AV system, and it is connected to each control
unit by means of communication. It operates each system according to com-
munication signals from the NAVI control unit.
 The NAVI control unit includes the audio, hands-free phone, navigation, and
vehicle information functions.
 It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
 It inputs the illumination signals that are required for the display dimming con-
trol.
 It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Action to take
U1200Cont Unit
FLASH- ROM
[U1200]An internal malfunction is detected in NAVI control unit
(FLASH-ROM).Replace NAVI control unit.

AV-56
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
U1201 NAVI CONTROL UNIT
U1201 NAVI CONTROL UNIT
DescriptionINFOID:0000000001728656
Replace the NAVI control unit if this DTC is displayed. Refer to XX-XX, "*****".
DTC LogicINFOID:0000000001728657
Part name Description
NAVI CONTORL UNIT Map data can be read from the map DVD-ROM by installing map DVD-ROM.
 It is the master unit of the MULTI AV system, and it is connected to each control
unit by means of communication. It operates each system according to com-
munication signals from the NAVI control unit.
 The NAVI control unit includes the audio, hands-free phone, navigation, and
vehicle information functions.
 It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
 It inputs the illumination signals that are required for the display dimming con-
trol.
 It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Action to take
U1201GYRO NO CONN
[U1201]Internal malfunction of NAVI control unit (gyrocompass
disconnection) is detected.Replace NAVI control unit.

AV
U1216 NAVI CONTROL UNIT
AV-57
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
C
D
E
F
G
H
I
J
K
L
MB A
O
P
U1216 NAVI CONTROL UNIT
DescriptionINFOID:0000000001728658
Replace the NAVI control unit if this DTC is displayed. Refer to XX-XX, "*****".
DTC LogicINFOID:0000000001728659
Part name Description
NAVI CONTORL UNIT Map data can be read from the map DVD-ROM by installing map DVD-ROM.
 It is the master unit of the MULTI AV system, and it is connected to each control
unit by means of communication. It operates each system according to com-
munication signals from the NAVI control unit.
 The NAVI control unit includes the audio, hands-free phone, navigation, and
vehicle information functions.
 It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
 It inputs the illumination signals that are required for the display dimming con-
trol.
 It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Action to take
U1216CAN CONT
[U1216]Internal malfunction of NAVI control unit (CAN controller)
is detected.Replace NAVI control unit.

AV-58
< COMPONENT DIAGNOSIS >[AUDIO WITH NAVIGATION]
U1217 NAVI CONTROL UNIT
U1217 NAVI CONTROL UNIT
DescriptionINFOID:0000000001728660
Replace the NAVI control unit if this DTC is displayed. Refer to XX-XX, "*****".
DTC LogicINFOID:0000000001728661
Part name Description
NAVI CONTORL UNIT Map data can be read from the map DVD-ROM by installing map DVD-ROM.
 It is the master unit of the MULTI AV system, and it is connected to each control
unit by means of communication. It operates each system according to com-
munication signals from the NAVI control unit.
 The NAVI control unit includes the audio, hands-free phone, navigation, and
vehicle information functions.
 It is connected to ECM and combination meter via CAN communication to ob-
tain necessary information for the vehicle information function.
 It inputs the illumination signals that are required for the display dimming con-
trol.
 It inputs the signals for driving status recognition (vehicle speed, reverse and
parking brake).
DTCDisplay contents of
CONSULT-IIIDTC Detection Condition Action to take
U1217BLUETOOTH MODULE
CONN
[U1217]Internal malfunction of NAVI control unit (Bluetooth mod-
ule connection malfunction) is detected.Replace NAVI control unit.