headlamp NISSAN TIIDA 2007 Service Owner's Manual

HOOD
DLK-583
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
REMOVAL AND INSTALLATION
HOOD
Fitting AdjustmentINFOID:0000000001732035
FRONT END HEIGHT ADJUSTMENT AND LATERAL/LONGITUDINAL CLEARANCE ADJUST-
MENT
1. Remove the front grille. Refer to EXT-19, "Removal and Installation".
2. Remove hood lock. Rotate bumper rubber to adjust height until
hood becomes 1.0 to 1.5 mm lower than the fender.
3. Position hood lock and engage striker. Check hood lock and
striker for looseness. Tighten lock bolts to the specified torque.
4. Install the front grille. Refer to EXT-19, "
Removal and Installa-
tion".
CAUTION:
Adjust the clearance between hood and other parts so that the
dimensional difference left and right is as follows.
SURFACE MISMATCH ADJUSTMENT
1. Remove the front grille. Refer to EXT-19, "Removal and Installation".
2. Release hood lock, and adjust surface level difference of hood, fender, and headlamp according to the fit-
ting standard dimension, using RH and LH bumper rubbers.
3. Install and align the hood lock until the center of the striker and the hood lock are vertically aligned.
PIIB6508E
Hood and headlamp (B - B) : Less than 2.0 mm (0.08 in)
Hood and fender (C - C) : Less than 1.5 mm (0.06 in)
Hood and fender (D - D) : Less than 1.5 mm (0.06 in)PIIB2526J
Hood and front bumper (A - A) : -1.3 - 2.7 mm (-0.05 - 0.11 in)
Hood and fender (D - D) : -0.4 - 1.7 mm (-0.16 - 0.07 in)

RADIATOR CORE SUPPORT
DLK-589
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
RADIATOR CORE SUPPORT
Removal and InstallationINFOID:0000000001732039
REMOVAL
Radiator Core Support Upper
1. Remove the air duct. Refer to EM-27, "Removal and Installation" (HR16DE), EM-154, "Removal and
Installation" (MR18DE), or EM-269, "Removal and Installation" (K9K).
2. Remove the headlamp (LH/RH). Refer to EXL-84, "
Removal and Installation" .
3. Remove the hood lock assembly, and remove hood lock cable. Refer to DLK-585
.
4. Remove the air guide and hood lock cable clip.
5. Remove the washer tank inlet. Refer to WW-64, "
Removal and Installation" .
6. Remove the radiator core support upper.
Radiator Core Support Lower
1. Remove the air duct. Refer to EM-27, "Removal and Installation" (HR16DE), EM-154, "Removal and
Installation" (MR18DE), or EM-269, "Removal and Installation" (K9K).
2. Remove the front bumper. Refer to EXT-13, "
Removal and Installation" .
3. Remove the headlamp (LH/RH). Refer to EXL-84, "
Removal and Installation" .
4. Remove the hood lock assembly, and remove hood lock cable. Refer to DLK-585
.
5. Remove the air guide and hood lock cable mounting clip.
6. Remove the front bumper reinforcement. Refer to EXT-13, "
Removal and Installation".
7. Remove the radiator core lower stay.
8. Remove the undercover.
PIIB6515E
1. Radiator core support upper 2. Radiator core support lower 3. Radiator core support lower stay
4. Radiator core support side stay 5. Air guide
24.5 N·m (2.5 kg-m, 18 ft-lb)

FRONT FENDER
DLK-591
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
FRONT FENDER
Removal and InstallationINFOID:0000000001732040
REMOVAL
1. Remove the headlamp assemblies. Refer to EXL-84, "Removal and Installation".
2. Remove the cowl top cover (LH/RH). Refer to EXT-20, "
Removal and Installation".
3. Remove the front fender protector. Refer to DLK-591, "
Removal and Installation".
4. Remove the bolt and the front fender.
CAUTION:
While removing use a shop cloth to protect the vechicle body from damage.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 After installing, apply touch-up paint onto the head of the front fender bolts.
 After installing, check front fender adjustment. Refer to DLK-583, "
Fitting Adjustment" and DLK-592,
"Fitting Adjustment".
1. Front fender 2 Bolt (LH 7 bolts required) (RH 8 bolts
required)
LIIA2657E

DLK-734
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY, WITH SUPER LOCK]
HOOD
REMOVAL AND INSTALLATION
HOOD
Fitting AdjustmentINFOID:0000000001732053
FRONT END HEIGHT ADJUSTMENT AND LATERAL/LONGITUDINAL CLEARANCE ADJUST-
MENT
1. Remove the front grille. Refer to EXT-19, "Removal and Installation".
2. Remove hood lock. Rotate bumper rubber to adjust height until
hood becomes 1.0 to 1.5 mm lower than the fender.
3. Position hood lock and engage striker. Check hood lock and
striker for looseness. Tighten lock bolts to the specified torque.
4. Install the front grille. Refer to EXT-19, "
Removal and Installa-
tion".
CAUTION:
Adjust the clearance between hood and other parts so that the
dimensional difference left and right is as follows.
SURFACE MISMATCH ADJUSTMENT
1. Remove the front grille. Refer to EXT-19, "Removal and Installation".
2. Release hood lock, and adjust surface level difference of hood, fender, and headlamp according to the fit-
ting standard dimension, using RH and LH bumper rubbers.
3. Install and align the hood lock until the center of the striker and the hood lock are vertically aligned.
PIIB6508E
Hood and headlamp (B - B) : Less than 2.0 mm (0.08 in)
Hood and fender (C - C) : Less than 1.5 mm (0.06 in)
Hood and fender (D - D) : Less than 1.5 mm (0.06 in)PIIB2526J
Hood and front bumper (A - A) : -1.3 - 2.7 mm (-0.05 - 0.11 in)
Hood and fender (D - D) : -0.4 - 1.7 mm (-0.16 - 0.07 in)

DLK-740
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY, WITH SUPER LOCK]
RADIATOR CORE SUPPORT
RADIATOR CORE SUPPORT
Removal and InstallationINFOID:0000000001732057
REMOVAL
Radiator Core Support Upper
1. Remove the air duct. Refer to EM-27, "Removal and Installation" (HR16DE), EM-154, "Removal and
Installation" (MR18DE), or EM-269, "Removal and Installation" (K9K).
2. Remove the headlamp (LH/RH). Refer to EXL-84, "
Removal and Installation" .
3. Remove the hood lock assembly, and remove hood lock cable. Refer to DLK-736
.
4. Remove the air guide and hood lock cable clip.
5. Remove the washer tank inlet. Refer to WW-64, "
Removal and Installation" .
6. Remove the radiator core support upper.
Radiator Core Support Lower
1. Remove the air duct. Refer to EM-27, "Removal and Installation" (HR16DE), EM-154, "Removal and
Installation" (MR18DE), or EM-269, "Removal and Installation" (K9K).
2. Remove the front bumper. Refer to EXT-13, "
Removal and Installation" .
3. Remove the headlamp (LH/RH). Refer to EXL-84, "
Removal and Installation" .
4. Remove the hood lock assembly, and remove hood lock cable. Refer to DLK-736
.
5. Remove the air guide and hood lock cable mounting clip.
6. Remove the front bumper reinforcement. Refer to EXT-13, "
Removal and Installation".
7. Remove the radiator core lower stay.
8. Remove the undercover.
PIIB6515E
1. Radiator core support upper 2. Radiator core support lower 3. Radiator core support lower stay
4. Radiator core support side stay 5. Air guide
24.5 N·m (2.5 kg-m, 18 ft-lb)

DLK-742
< REMOVAL AND INSTALLATION >[WITHOUT I-KEY, WITH SUPER LOCK]
FRONT FENDER
FRONT FENDER
Removal and InstallationINFOID:0000000001732058
REMOVAL
1. Remove the headlamp assemblies. Refer to EXL-84, "Removal and Installation".
2. Remove the cowl top cover (LH/RH). Refer to EXT-20, "
Removal and Installation".
3. Remove the front fender protector. Refer to DLK-742, "
Removal and Installation".
4. Remove the bolt and the front fender.
CAUTION:
While removing use a shop cloth to protect the vechicle body from damage.
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
 After installing, apply touch-up paint onto the head of the front fender bolts.
 After installing, check front fender adjustment. Refer to DLK-734, "
Fitting Adjustment" and DLK-743,
"Fitting Adjustment".
1. Front fender 2 Bolt (LH 7 bolts required) (RH 8 bolts
required)
LIIA2657E

EC-5
C
D
E
F
G
H
I
J
K
L
M
ECA
N
O
P Component Function Check ..................................
316
Diagnosis Procedure .............................................316
Component Inspection (Fuel Pump) .....................318
IGNITION SIGNAL ...........................................319
Description ............................................................319
Component Function Check ..................................319
Diagnosis Procedure .............................................319
Component Inspection (Ignition Coil with Power
Transistor) .............................................................
322
Component Inspection (Condenser) .....................322
MALFUNCTION INDICATOR ...........................324
Description ............................................................324
Component Function Check ..................................324
Diagnosis Procedure .............................................324
POSITIVE CRANKCASE VENTILATION ........325
Description ............................................................325
Component Inspection ..........................................325
REFRIGERANT PRESSURE SENSOR ...........326
Description ............................................................326
Component Function Check ..................................326
Diagnosis Procedure .............................................326
ECU DIAGNOSIS .......................................328
ECM ..................................................................328
Reference Value ...................................................328
Wiring Diagram - ENGINE CONTROL SYSTEM - ..339
Fail Safe ...............................................................358
DTC Inspection Priority Chart .............................360
DTC Index ............................................................361
How to Set SRT Code ........................................363
Test Value and Test Limit ..................................365
SYMPTOM DIAGNOSIS ............................366
ENGINE CONTROL SYSTEM SYMPTOMS ....366
Symptom Table .....................................................366
NORMAL OPERATING CONDITION ...............370
Description ............................................................370
PRECAUTION ............................................371
PRECAUTIONS ................................................371
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
371
Precaution for Procedure without Cowl Top Cover ..371
Precautions For Xenon Headlamp Service ...........371
On Board Diagnostic (OBD) System of Engine
and A/T ..................................................................
372
General Precautions .............................................372
PREPARATION .........................................375
PREPARATION ................................................375
Special Service Tools ............................................375
Commercial Service Tools ....................................375
ON-VEHICLE MAINTENANCE ..................377
FUEL PRESSURE ...........................................377
Inspection ..............................................................377
EVAPORATIVE EMISSION SYSTEM .............379
Inspection ..............................................................379
SERVICE DATA AND SPECIFICATIONS
(SDS) ..........................................................
380
SERVICE DATA AND SPECIFICATIONS
(SDS) ...............................................................
380
Idle Speed .............................................................380
Ignition Timing .......................................................380
Calculated Load Value ..........................................380
Mass Air Flow Sensor ............................................380
HR16DE (WITHOUT EURO-OBD)
BASIC INSPECTION .................................
381
DIAGNOSIS AND REPAIR WORKFLOW ......381
Work Flow ..............................................................381
Diagnostic Work Sheet ..........................................383
INSPECTION AND ADJUSTMENT ................385
BASIC INSPECTION ...............................................385
BASIC INSPECTION : Special Repair Require-
ment .......................................................................
385
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ......................................................
388
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ...............................
388
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement ....
388
IDLE SPEED ............................................................388
IDLE SPEED : Description ....................................389
IDLE SPEED : Special Repair Requirement .........389
IGNITION TIMING ....................................................389
IGNITION TIMING : Description ............................389
IGNITION TIMING : Special Repair Requirement ..389
ACCELERATOR PEDAL RELEASED POSITION
LEARNING ...............................................................
389
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Description .......................................
389
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Special Repair Requirement ............
389
THROTTLE VALVE CLOSED POSITION LEARN-
ING ...........................................................................
390
THROTTLE VALVE CLOSED POSITION
LEARNING : Description .......................................
390
THROTTLE VALVE CLOSED POSITION
LEARNING : Special Repair Requirement ............
390
IDLE AIR VOLUME LEARNING ..............................390
IDLE AIR VOLUME LEARNING : Description .......390

EC-9
C
D
E
F
G
H
I
J
K
L
M
ECA
N
O
P
MALFUNCTION INDICATOR ...........................630
Description ............................................................630
Component Function Check ..................................630
Diagnosis Procedure .............................................630
POSITIVE CRANKCASE VENTILATION ........631
Description ............................................................631
Component Inspection ..........................................631
REFRIGERANT PRESSURE SENSOR ...........632
Description ............................................................632
Component Function Check ..................................632
Diagnosis Procedure .............................................632
VSS ...................................................................634
Description ............................................................634
Diagnosis Procedure .............................................634
ECU DIAGNOSIS .......................................635
ECM ..................................................................635
Reference Value ...................................................635
Wiring Diagram - ENGINE CONTROL SYSTEM - ..646
Fail Safe ...............................................................665
DTC Inspection Priority Chart .............................667
DTC Index ............................................................667
SYMPTOM DIAGNOSIS ............................670
ENGINE CONTROL SYSTEM SYMPTOMS ....670
Symptom Table .....................................................670
NORMAL OPERATING CONDITION ...............674
Description ............................................................674
PRECAUTION ............................................675
PRECAUTIONS ................................................675
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" ...............................................................
675
Precaution for Procedure without Cowl Top Cover ..675
Precautions For Xenon Headlamp Service ...........675
On Board Diagnostic (OBD) System of Engine
and A/T ..................................................................
676
General Precautions .............................................676
PREPARATION .........................................679
PREPARATION ................................................679
Special Service Tools ............................................679
Commercial Service Tools ....................................679
ON-VEHICLE MAINTENANCE ..................681
FUEL PRESSURE ............................................681
Inspection ..............................................................681
EVAPORATIVE EMISSION SYSTEM ..............683
Inspection ..............................................................683
SERVICE DATA AND SPECIFICATIONS
(SDS) ..........................................................
684
SERVICE DATA AND SPECIFICATIONS
(SDS) ...............................................................
684
Idle Speed .............................................................684
Ignition Timing .......................................................684
MR18DE
BASIC INSPECTION .................................
685
DIAGNOSIS AND REPAIR WORKFLOW ......685
Work Flow ..............................................................685
Diagnostic Work Sheet ..........................................687
INSPECTION AND ADJUSTMENT ................689
BASIC INSPECTION ...............................................689
BASIC INSPECTION : Special Repair Require-
ment .......................................................................
689
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT ......................................................
692
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Description ...............................
692
ADDITIONAL SERVICE WHEN REPLACING
CONTROL UNIT : Special Repair Requirement ....
692
IDLE SPEED ............................................................692
IDLE SPEED : Description ....................................692
IDLE SPEED : Special Repair Requirement .........692
IGNITION TIMING ....................................................693
IGNITION TIMING : Description ............................693
IGNITION TIMING : Special Repair Requirement ..693
ACCELERATOR PEDAL RELEASED POSITION
LEARNING ...............................................................
693
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Description .......................................
693
ACCELERATOR PEDAL RELEASED POSITION
LEARNING : Special Repair Requirement ............
693
THROTTLE VALVE CLOSED POSITION LEARN-
ING ...........................................................................
694
THROTTLE VALVE CLOSED POSITION
LEARNING : Description .......................................
694
THROTTLE VALVE CLOSED POSITION
LEARNING : Special Repair Requirement ............
694
IDLE AIR VOLUME LEARNING ..............................694
IDLE AIR VOLUME LEARNING : Description .......694
IDLE AIR VOLUME LEARNING : Special Repair
Requirement ..........................................................
694
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR .....................................................................
696
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR : Description ..............................................
696
MIXTURE RATIO SELF-LEARNING VALUE
CLEAR : Special Repair Requirement ...................
696

EC-13
C
D
E
F
G
H
I
J
K
L
M
ECA
N
O
P
ASCD BRAKE SWITCH ...................................964
Description ............................................................964
Component Function Check ..................................964
Diagnosis Procedure .............................................964
Component Inspection (ASCD Brake Switch) .......966
Component Inspection (ASCD Clutch Switch) ......966
ASCD INDICATOR ...........................................968
Description ............................................................968
Component Function Check ..................................968
Diagnosis Procedure .............................................968
COOLING FAN .................................................969
Description ............................................................969
Component Function Check ..................................969
Diagnosis Procedure .............................................969
Component Inspection ..........................................971
ELECTRICAL LOAD SIGNAL .........................973
Description ............................................................973
Component Function Check ..................................973
Diagnosis Procedure .............................................973
FUEL INJECTOR .............................................975
Description ............................................................975
Component Function Check ..................................975
Diagnosis Procedure .............................................975
Component Inspection ..........................................976
FUEL PUMP .....................................................978
Description ............................................................978
Component Function Check ..................................978
Diagnosis Procedure .............................................978
Component Inspection (Fuel Pump) .....................980
IGNITION SIGNAL ...........................................981
Description ............................................................981
Component Function Check ..................................981
Diagnosis Procedure .............................................981
Component Inspection (Ignition Coil with Power
Transistor) .............................................................
984
Component Inspection (Condenser) .....................984
MALFUNCTION INDICATOR ...........................986
Description ............................................................986
Component Function Check ..................................986
Diagnosis Procedure .............................................986
POSITIVE CRANKCASE VENTILATION ........987
Description ............................................................987
Component Inspection ..........................................987
REFRIGERANT PRESSURE SENSOR ...........988
Description ............................................................988
Component Function Check ..................................988
Diagnosis Procedure .............................................988
ECU DIAGNOSIS .......................................990
ECM ..................................................................990
Reference Value ...................................................990
Wiring Diagram - ENGINE CONTROL SYSTEM - 1000
Fail Safe ..............................................................1017
DTC Inspection Priority Chart ...........................1019
DTC Index ...........................................................1020
How to Set SRT Code ......................................1021
Test Value and Test Limit .................................1023
SYMPTOM DIAGNOSIS ...........................1024
ENGINE CONTROL SYSTEM .......................1024
Symptom Table ...................................................1024
NORMAL OPERATING CONDITION ............1028
Description ...........................................................1028
PRECAUTION ...........................................1029
PRECAUTIONS ..............................................1029
Precaution for Supplemental Restraint System
(SRS) "AIR BAG" and "SEAT BELT PRE-TEN-
SIONER" .............................................................
1029
Precaution for Procedure without Cowl Top Cover 1029
Precautions For Xenon Headlamp Service .........1029
On Board Diagnostic (OBD) System of Engine ...1030
General Precautions ............................................1030
PREPARATION ........................................1033
PREPARATION ..............................................1033
Special Service Tools ..........................................1033
Commercial Service Tools ...................................1033
ON-VEHICLE REPAIR ..............................1035
FUEL PRESSURE ..........................................1035
Inspection ............................................................1035
EVAPORATIVE EMISSION SYSTEM ............1037
Inspection ............................................................1037
SERVICE DATA AND SPECIFICATIONS
(SDS) .........................................................
1038
SERVICE DATA AND SPECIFICATIONS
(SDS) ..............................................................
1038
Idle Speed ...........................................................1038
Ignition Timing .....................................................1038
Calculated Load Value ........................................1038
Mass Air Flow Sensor ..........................................1038
K9K
BASIC INSPECTION ................................
1039
DIAGNOSIS AND REPAIR WORKFLOW .....1039
Work Flow ............................................................1039
Diagnostic Work Sheet ........................................1041
INSPECTION AND ADJUSTMENT ...............1043
BASIC INSPECTION .............................................1043
BASIC INSPECTION : Description ......................1043

EC-22
< BASIC INSPECTION >[HR16DE (WITH EURO-OBD)]
INSPECTION AND ADJUSTMENT
INSPECTION AND ADJUSTMENT
BASIC INSPECTION
BASIC INSPECTION : Special Repair RequirementINFOID:0000000001161123
1.INSPECTION START
1. Check service records for any recent repairs that may indicate a related malfunction, or a current need for
scheduled maintenance.
2. Open engine hood and check the following:
- Harness connectors for improper connections
- Wiring harness for improper connections, pinches and cut
- Vacuum hoses for splits, kinks and improper connections
- Hoses and ducts for leaks
- Air cleaner clogging
- Gasket
3. Confirm that electrical or mechanical loads are not applied.
- Headlamp switch is OFF.
- Air conditioner switch is OFF.
- Rear window defogger switch is OFF.
- Steering wheel is in the straight-ahead position, etc.
4. Start engine and warm it up until engine coolant temperature
indicator points the middle of gauge.
Ensure engine stays below 1,000 rpm.
5. Run engine at about 2,000 rpm for about 2 minutes under no
load.
6. Make sure that no DTC is displayed with CONSULT-III or GST.
Is any DTC detected?
YES >> GO TO 2.
NO >> GO TO 3.
2.REPAIR OR REPLACE
Repair or replace components as necessary according to corresponding Diagnostic Procedure.
>> GO TO 3
3.CHECK TARGET IDLE SPEED
1. Run engine at about 2,000 rpm for about 2 minutes under no load.
SEF983U
SEF976U
SEF977U