reverse NISSAN TIIDA 2007 Service Repair Manual

OIL COOLER
LU-19
< ON-VEHICLE REPAIR >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
LU
N
P O
ON-VEHICLE REPAIR
OIL COOLER
ComponentsINFOID:0000000001532089
Removal and InstallationINFOID:0000000001532090
REMOVAL
WARNING:
Make sure engine is cool before performing this operation.
1. Remove engine undercover using power tool.
2. Remove coolant hoses from oil cooler.
NOTE:
Pinch hoses to prevent coolant leaking.
3. Remove oil filter. Refer to LU-18, "
Removal and Installation".
4. Remove connector bolt and oil cooler.
INSTALLATION
Installation is in the reverse order of removal.
PBIC4487E
1. Oil cooler hose 2. Oil cooler hose 3. O-ring
4. Oil cooler 5. Connector bolt 6. Oil filter
A. Refer to LU-19, "
Removal and Installation"

OIL PUMP
LU-21
< ON-VEHICLE REPAIR >[MR18DE]
C
D
E
F
G
H
I
J
K
L
MA
LU
N
P O
2. Remove oil pump.
 Loosen bolts in reverse order as shown.
INSTALLATION
1. Install oil pump.
 Tighten bolts in numerical order as shown.
2. Install the timing chain and oil pump drive chain. Refer to EM-177, "
Removal and Installation". 1 : Oil pump
2 : Oil pan (upper)
⇐: Engine front
PBIC3532J
1 : Oil pump
2 : Oil pan (upper)
⇐: Engine front
PBIC3532J

OIL FILTER BRACKET
LU-29
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
LU
N
P O
ON-VEHICLE REPAIR
OIL FILTER BRACKET
Exploded ViewINFOID:0000000001381541
Removal and InstallationINFOID:0000000001381542
REMOVAL
CAUTION:
 Be careful not to get burned when the engine and engine oil are hot.
 When removing, prepare a shop cloth to absorb any oil leakage or spillage.
 Do not allow engine oil to adhere to the drive belts.
 Completely wipe off any oil that adhere to the engine and the vehicle.
1. Remove engine undercover using power tool.
2. Remove oil filter. Refer to LU-28, "
Replacement".
3. Disconnect oil pressure switch electrical connector.
4. Remove oil filter bracket.
INSTALLATION
Installation is in the reverse order of removal.
1. O-ring 2. Oil filter bracket 3. Oil pressure switch
4. Oil filter 5. O-ring 6. Connecting bolt
A. To oil cooler
E1BIA0012GB

OIL COOLER
LU-31
< ON-VEHICLE REPAIR >[K9K]
C
D
E
F
G
H
I
J
K
L
MA
LU
N
P O
9. Disconnect oil pressure switch electrical connector.
10. Remove the oil cooler connecting stud.
11. Remove oil cooler.
INSTALLATION
Installation is in the reverse order of removal.
 Replace the O-ring of the oil cooler, positioning the lip of the seal behind the lug of the oil cooler.
 Confirm that no foreign objects are adhering to the seal contact areas of the oil cooler and cylinder block.
InspectionINFOID:0000000001381545
INSPECTION AFTER REMOVAL
Check oil cooler for cracks and clogging by blowing through coolant inlet. If necessary, replace oil cooler
assembly.

LU-32
< ON-VEHICLE REPAIR >[K9K]
OIL PUMP
OIL PUMP
Exploded ViewINFOID:0000000001381546
Removal and InstallationINFOID:0000000001381547
REMOVAL
1. Remove the battery negative cable.
2. Remove the engine undercover.
3. Remove the RH front wheel and tire. Refer to WT-6, "
Rotation".
4. Remove RH fender protector. Refer to EXT-22, "
Removal and Installation".
5. Remove front driveshaft assembly RH. Refer to FA X - 11 , "
Removal and Installation (Right Side)".
6. Remove driveshaft center bearing bracket.
7. Remove lower torque rod. Refer to EM-302, "
Exploded View".
8. Remove oil pan. Refer to EM-284, "
Removal and Installation".
9. Remove oil pump drive chain.
10. Remove oil pump assembly.
INSTALLATION
Installation is in the reverse order of removal.
1. Oil pump drive chain 2. Crankshaft sprocket (oil pump drive
chain)3. Oil pump
E1BIA0028GB

MA-26
< ON-VEHICLE MAINTENANCE >
ENGINE MAINTENANCE (HR16DE)
AIR CLEANER FILTER : Removal and Installation
INFOID:0000000001730850
REMOVAL
1. Push the tabs (A) of both ends of the air cleaner cover (1) into
the inside (B).
2. Pull up the air cleaner cover (1) and remove it (C).
3. Remove air cleaner filter (1) and holder (2) assembly from the
air cleaner case.
4. Remove the air cleaner filter (1) from the holder (2).
INSPECTION AFTER REMOVAL
It is necessary to clean air cleaner filter or replace it at the recommended intervals, more often under dusty
conditions. Refer to MA-7, "
Periodic Maintenance".
 Blow air into the back side of air cleaner filter until no objects spray
out.
INSTALLATION
Installation is in the reverse order of removal.
 Install the air cleaner cover (1) in the direction shown.
ENGINE OIL
PBIC3557J
PBIC3558J
SMA384C
2 : Air cleaner filter
3 : Holder
PBIC3559J

ENGINE MAINTENANCE (HR16DE)
MA-29
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
MB
MAN
OA
 Never drop or shock spark plug.
 Never use a wire brush for cleaning.
 If plug tip is covered with carbon, spark plug cleaner may be
used.
Checking and adjusting plug gap is not required between
change intervals.
INSTALLATION
Installation is the reverse order of removal.
SPARK PLUG : InspectionINFOID:0000000001277617
INSPECTION AFTER REMOVAL
Use the standard type spark plug for normal condition.
CAUTION:
 Never drop or shock spark plug.
 Never use a wire brush for cleaning.
 If plug tip is covered with carbon, spark plug cleaner may be
used.Cleaner air
pressure:Less than 588 kPa (6 kg/cm
2, 85 psi)
Cleaning time: Less than 20 seconds
SMA773C
JPBIA0031ZZ
Plug type : Platinum tipped
Make : NGK
Part number : PLZKAR6AP-11
Gap (nominal) : 1.1 mm (0.043 in)
Spark plug (Standard type): : PLZKAR6AP-11
Cleaner air pressure:
Less than 588 kPa (6 kg/cm
2, 85 psi)
Cleaning time:
Less than 20 seconds
SMA773C

ENGINE MAINTENANCE (MR18DE)
MA-35
< ON-VEHICLE MAINTENANCE >
C
D
E
F
G
H
I
J
K
L
MB
MAN
OA
FUEL LINES : InspectionINFOID:0000000001277628
Inspect fuel lines, filler cap and tank for improper attachment, leaks,
cracks, damage, loose connections, chafing or deterioration.
If necessary, repair or replace damaged parts.
AIR CLEANER FILTER
AIR CLEANER FILTER : Removal and InstallationINFOID:0000000001730862
REMOVAL
1. Push the tabs (A) of both ends of the air cleaner cover (1) into
the inside (B).
2. Pull up the air cleaner cover (1) and remove it (C).
3. Remove air cleaner filter (1) and holder (2) assembly from the
air cleaner case.
4. Remove the air cleaner filter (1) from the holder (2).
INSPECTION AFTER REMOVAL
It is necessary to clean air cleaner filter or replace it at the recommended intervals, more often under dusty
conditions. Refer to MA-7, "
Periodic Maintenance".
 Blow air into the back side of air cleaner filter until no objects spray
out.
INSTALLATION
Installation is in the reverse order of removal.
SMA803A
PBIC3557J
PBIC3558J
SMA384C

MA-46
< ON-VEHICLE MAINTENANCE >
ENGINE MAINTENANCE (K9K)
AIR CLEANER FILTER
AIR CLEANER FILTER : Removal and InstallationINFOID:0000000001730875
REMOVAL
1. Push the tabs (A) of both ends of the air cleaner cover (1) into
the inside (B).
2. Pull up the air cleaner cover (1) and remove it (C).
3. Remove air cleaner filter (1) and holder (2) assembly from the
air cleaner case.
4. Remove the air cleaner filter (1) from the holder (2).
INSPECTION AFTER REMOVAL
It is necessary to clean air cleaner filter or replace it at the recommended intervals, more often under dusty
conditions. Refer to MA-7, "
Periodic Maintenance".
 Blow air into the back side of air cleaner filter until no objects spray
out.
INSTALLATION
Installation is in the reverse order of removal.
 Install the air cleaner cover (1) in the direction shown.
ENGINE OIL
PBIC3557J
PBIC3558J
SMA384C
2 : Air cleaner filter
3 : Holder
PBIC3559J

DOOR MIRROR
MIR-7
< REMOVAL AND INSTALLATION >
C
D
E
F
G
H
I
J
K
MA
B
MIR
N
O
P
REMOVAL AND INSTALLATION
DOOR MIRROR
Removal and InstallationINFOID:0000000001716808
CAUTION:
Be careful not to damage the mirror body.
REMOVAL
1. Remove the front door finisher. Refer to INT-13, "Removal and Installation".
2. Disconnect the harness connector of door mirror.
3. Using a suitable tool remove door mirror base cover.
CAUTION:
 Do not reuse the disassembled door mirror base cover.
 Be careful not to damage the door panel with a tool.
4. Remove the door mirror bolts, and remove the door mirror
assembly.
CAUTION:
Do not use force to remove the door mirror assembly by
force because it is attached by clip.
INSTALLATION
Installation is in the reverse order of removal.
PIIB2638J
1. Door mirror base cover 2. Door mirror
PIIB2679E
PIIB6288E