lock NISSAN TIIDA 2007 Service Repair Manual

TRUNK LID
DLK-237
< REMOVAL AND INSTALLATION >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
TRUNK LID
Fitting AdjustmentINFOID:0000000001315840
Longitudinal and lateral clearance adjustment
1. With the striker released, loosen the trunk lid hinge nuts and close the trunk lid.
2. Make the lateral clearance and the clearance to the rear window glass equal. Then open the trunk lid to
tighten the nuts.
Surface height adjustment
1. Loosen the striker bolts. Raise the striker to the top position, and temporarily tighten the upper bolt.
2. Close the trunk lid lightly and adjust the surface height. Then open the trunk lid and tighten the striker
bolts.
Trunk Lid AssemblyINFOID:0000000001315841
REMOVAL
1. Remove the trunk lid finisher. Refer to INT-17, "Removal and Installation" .
2. Remove the trunk lid wire harness.
1. Rear fender 2. Trunk lid 3. Rear combination lamp
4. Rear bumper fascia a. 4.0 ± 1.0 mm (0.16 ± 0.04 in) b. 3.5 ± 1.0 mm (0.14 ± 0.04 in)
c. 4.5 ± 1.7 mm (0.03 ± 0.06 in) d. 7.0 ± 2.2 mm (0.28 ± 0.09 in)
LIIA2932E

DLK-238
< REMOVAL AND INSTALLATION >[WITH I-KEY, WITHOUT SUPER LOCK]
TRUNK LID
3. Remove the nuts (a) and the trunk lid assembly (1).
INSTALLATION
Installation is in the reverse order of removal.
CAUTION:
After installing, apply touch-up paint (body color) to the head of the hinge nuts.
Trunk Lid LockINFOID:0000000001315842
REMOVAL
1. Remove the trunk lid finisher. Refer to INT-17, "Removal and Installation".
2. If equipped, disconnect the trunk lid lock cylinder rod.
3. Remove the release cable.
4. Disconnect the electrical connector (a), remove the bolts (b) and
the trunk lid lock (1).
INSTALLATION
Installation is in the reverse order of removal.
Trunk Lid StrikerINFOID:0000000001315843
REMOVAL
1. Remove the trunk rear plate and trunk rear finisher. Refer to INT-35, "Removal and Installation".
2. Remove the bolts, disconnect the electrical connector and remove the trunk lock actuator.
3. Remove the bolt and disconnect the trunk lid release cable.
LIIA2933E
LIIA2935E

TRUNK LID
DLK-239
< REMOVAL AND INSTALLATION >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
4. Remove the bolts (a) and the trunk lid striker (1).
INSTALLATION
Installation is in the reverse order of removal.
LIIA2934E

DLK-240
< BASIC INSPECTION >[WITH I-KEY & SUPER LOCK]
DIAGNOSIS AND REPAIR WORKFLOW
BASIC INSPECTION
DIAGNOSIS AND REPAIR WORKFLOW
Work FlowINFOID:0000000001396667
OVERALL SEQUENCE
DETAILED FLOW
ALKIA0246GB

DIAGNOSIS AND REPAIR WORKFLOW
DLK-241
< BASIC INSPECTION >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
1.GET INFORMATION FOR SYMPTOM
Get the detailed information from the customer about the symptom (the condition and the environment when
the incident/malfunction occurred).
>> GO TO 2.
2.CHECK DTC
1. Check DTC for Intelligent Key unit and BCM.
2. Perform the following procedure if DTC is displayed.
- Erase DTC.
- Study the relationship between the cause detected by DTC and the symptom described by the customer.
3. Check related service bulletins for information.
Is any symptom described and any DTC detected?
Symptom is described, DTC is displayed>>GO TO 3.
Symptom is described, DTC is not displayed>>GO TO 4.
Symptom is not described, DTC is displayed>>GO TO 5.
3.CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 5.
4.CONFIRM THE SYMPTOM
Confirm the symptom described by the customer.
Connect CONSULT-III to the vehicle in “DATA MONITOR ” mode and check real time diagnosis results.
Verify relation between the symptom and the condition when the symptom is detected.
>> GO TO 6.
5.PERFORM DTC CONFIRMATION PROCEDURE
Perform DTC Confirmation Procedure for the displayed DTC, and then check that DTC is detected again.
If two or more DTCs are detected, refer to XX-XX, "*****"
(Intelligent Key unit), XX-XX, "*****" (BCM) and
determine trouble diagnosis order.
Is DTC detected?
YES >> GO TO 8.
NO >> Refer to XX-XX, "*****"
.
6.PERFORM BASIC INSPECTION
Perform Basic Inspection. Refer to DLK-440, "
Basic Inspection".
>> GO TO 7.
7.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM TABLE
Detect malfunctioning system according to Symptom Table based on the confirmed symptom in step 4.
>> GO TO 8.
8.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE
Inspect according to Diagnostic Procedure of the system.
NOTE:
The Diagnostic Procedure described based on open circuit inspection. A short circuit inspection is also
required for the circuit check in the Diagnostic Procedure.
>> GO TO 9.

DLK-242
< BASIC INSPECTION >[WITH I-KEY & SUPER LOCK]
DIAGNOSIS AND REPAIR WORKFLOW
9.REPAIR OR REPLACE THE MALFUNCTIONING PART
1. Repair or replace the malfunctioning part.
2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replace-
ment.
3. Check DTC. If DTC is displayed, erase it.
>> GO TO 10.
10.FINAL CHECK
When DTC was detected in step 2, perform DTC Confirmation Procedure or Component Function Check
again, and then check that the malfunction have been repaired securely.
When symptom was described from the customer, refer to confirmed symptom in step 3 or 4, and check that
the symptom is not detected.
Does the symptom reappear?
YES (DTC is detected)>>GO TO 8.
YES (Symptom remains)>>GO TO 6.
NO >>INSPECTION END

INSPECTION AND ADJUSTMENT
DLK-243
< BASIC INSPECTION >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
INSPECTION AND ADJUSTMENT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Description
INFOID:0000000001396668
Perform the system initialization when replacing Intelligent Key unit, replacing Intelligent Key or registering an
additional Intelligent Key.
ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT : Special Repair Re-
quirement
INFOID:0000000001396669
Refer to the CONSULT-III Operation Manual-NATS.

DLK-244
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
DOOR LOCK FUNCTION
FUNCTION DIAGNOSIS
DOOR LOCK FUNCTION
DOOR LOCK AND UNLOCK SWITCH
DOOR LOCK AND UNLOCK SWITCH : System DiagramINFOID:0000000001396670
DOOR LOCK AND UNLOCK SWITCH OPERATION
DOOR LOCK AND UNLOCK SWITCH INDICATOR OPERATION
DOOR LOCK AND UNLOCK SWITCH : System DescriptionINFOID:0000000001396671
DOOR LOCK AND UNLOCK SWITCH OPERATION
Functions available by operating the door lock and unlock switch on driver or passenger door. Interlocked with
the lock/unlock operation of door lock and unlock switch, door lock actuators of all doors are locked/unlocked.
Operation Condition
If the following conditions are not satisfied, door lock/unlock operation is not performed even if the door lock
and unlock switch is operated.
ALKIA0710GB
JMKIA0408GB

DOOR LOCK FUNCTION
DLK-245
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
NOTE:
When the door lock is locked with Intelligent Key or door request switch (in super lock set state), door lock and
unlock switch operation will be invalid until either following condition is satisfied.
 Turn ignition switch ON.
 Unlock with Intelligent key or door request switch.
DOOR LOCK AND UNLOCK SWITCH INDICATOR OPERATION
Door lock and unlock switch indicator indicates door lock status. The indicator turn ON while ignition switch is
ON and door lock is locked or super lock is set. If any door is opened, the indicator will turn OFF.
Door lock and unlock switch indicator have the following 2 functions.
1 Minute Timer
A timer must be running to turn OFF the indicator. The timer will be running for 1 minute after super lock set or
lock with Intelligent Key, door request switch or auto door lock.
30 Minutes Timer
A timer must be running to turn OFF the indicator. The timer will be running for 30 minutes after locking with
door lock and unlock switch.
NOTE:
1 minute timer condition is satisfied during 30 minutes timer is active, 30 minutes timer is not change to 1
minute.
Door lock and unlock switch Operation condition
Lock operationFollowing all conditions are satisfied.
 Except driver side doors are closed.
 Doors are not locked with Intelligent Key or door request switch.
Unlock operationFollowing all conditions are satisfied.
 Doors are not locked with Intelligent Key or door request switch.

DLK-246
< FUNCTION DIAGNOSIS >[WITH I-KEY & SUPER LOCK]
DOOR LOCK FUNCTION
DOOR LOCK AND UNLOCK SWITCH : Component Parts Location
INFOID:0000000001396672
1. BCM M18, M19, M20
(view with glove box removed)2. Intelligent Key unit M52 3. Front door switch (driver side) B34
(Passenger side) B27
4. Front door lock actuator (driver side) D14
(Passenger side) D114
Door unlock sensor (driver side) D145. Rear door switch LH B71
RH B536. Rear door lock actuator LH D205
RH D305
7. Key switch and ignition knob switch (A/T)
M328. Key switch and ignition knob switch
(M/T) M329. Instrument panel warning lamp as-
sembly (door lock) M37
ALKIA0811ZZ