switch NISSAN TIIDA 2007 Service Repair Manual

DOOR SWITCH
DLK-65
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
DOOR SWITCH
DRIVER SIDE
DRIVER SIDE : DescriptionINFOID:0000000001396536
Detects door open/closed condition.
DRIVER SIDE : Component Function CheckINFOID:0000000001396537
1.CHECK FUNCTION
With CONSULT-III
Check door switches “DOOR SW-DR” in “Data Monitor” mode with CONSULT-III.
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Refer to DLK-65, "
DRIVER SIDE : Diagnosis Procedure".
DRIVER SIDE : Diagnosis ProcedureINFOID:0000000001396538
1.CHECK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between BCM connector and ground with oscillo-
scope.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
2.CHECK DOOR SWITCH CIRCUIT
Monitor item Condition
DOOR SW-DR OPEN :ON
CLOSE :OFF
ALKIA0745ZZ
Te r m i n a l s
Door conditionVoltage (V)
(Approx.) (+)
(–)
BCM
connectorTe r m i n a l
M18 29 GroundOPEN 0
CLOSE
JPMIA0011GB

DLK-66
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR SWITCH
1. Disconnect BCM and driver door switch connectors.
2. Check continuity between BCM connector (A) M18 terminal 29
and door switch connector (B) B34 terminal 2.
3. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness between BCM and door switch.
3.CHECK DOOR SWITCH
Check door switch.
Refer to DLK-66, "
DRIVER SIDE : Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace front door switch (driver side). Refer to XX-XX, "*****"
.
4.CHECK INTERMITTENT INCIDENT
Refer to @@@.
>> INSPECTION END
DRIVER SIDE : Component InspectionINFOID:0000000001396539
1.CHECK DOOR SWITCH
1. Turn ignition switch OFF.
2. Check door switch.
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Replace front door switch (driver side). Refer to XX-XX, "*****"
.
PASSENGER SIDE
BCM connector TerminalDoor switch
connectorTerminal Continuity
M18 29 B34 2 Yes
BCM connector Terminal
GroundContinuity
M18 29 No
ALKIA0746ZZ
ALKIA0747ZZ
Te r m i n a l
Door switch condition Continuity
Door switch
2 Ground part of door switchPressed Yes
Released No

DOOR SWITCH
DLK-67
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
PASSENGER SIDE : DescriptionINFOID:0000000001396540
Detects door open/closed condition.
PASSENGER SIDE : Component Function CheckINFOID:0000000001396541
1.CHECK FUNCTION
With CONSULT-III
Check door switches “DOOR SW-AS” in “Data Monitor” mode with CONSULT-III.
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Refer to DLK-67, "
PASSENGER SIDE : Diagnosis Procedure".
PASSENGER SIDE : Diagnosis ProcedureINFOID:0000000001396542
1.CHECK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between BCM connector and ground with oscillo-
scope.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
2.CHECK DOOR SWITCH CIRCUIT
1. Disconnect BCM and passenger door switch connectors.
Monitor item Condition
DOOR SW-ASOPEN : ON
CLOSE : OFF
ALKIA0749ZZ
Te r m i n a l s
Door conditionVoltage (V)
(Approx.) (+)
(–)
BCM
connectorTe r m i n a l
M18 30 GroundOPEN 0
CLOSE
JPMIA0011GB

DLK-68
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR SWITCH
2. Check continuity between BCM connector (A) M18 terminal 30
and passenger door switch connector (B) B27 terminal 2.
3. Check continuity between BCM connector (A) M18 terminal 30
and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness between BCM and door switch.
3.CHECK DOOR SWITCH
Check door switch.
Refer to DLK-68, "
PASSENGER SIDE : Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace front door switch (passenger side). Refer to XX-XX, "*****"
.
4.CHECK INTERMITTENT INCIDENT
Refer to @@@.
>> INSPECTION END
PASSENGER SIDE : Component InspectionINFOID:0000000001396543
1.CHECK DOOR SWITCH
1. Turn ignition switch OFF.
2. Check passenger door switch.
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Replace front door switch (passenger side). Refer to XX-XX, "*****"
.
REAR LH
BCM connector TerminalDoor switch
connectorTerminal Continuity
M18 30 B27 2 Yes
BCM connector Terminal
GroundContinuity
M18 30 No
ALKIA0748ZZ
ALKIA0747ZZ
Te r m i n a l
Door switch condition Continuity
Door switch
2 Ground part of door switchPressed Yes
Released No

DOOR SWITCH
DLK-69
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
REAR LH : DescriptionINFOID:0000000001396544
Detects door open/closed condition.
REAR LH : Component Function CheckINFOID:0000000001396545
1.CHECK FUNCTION
With CONSULT-III
Check door switches “DOOR SW-RL” in “Data Monitor” mode with CONSULT-III.
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Refer to DLK-69, "
REAR LH : Diagnosis Procedure".
REAR LH : Diagnosis ProcedureINFOID:0000000001396546
1.CHECK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between BCM connector and ground with oscillo-
scope.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
2.CHECK DOOR SWITCH CIRCUIT
1. Disconnect BCM connector and rear door switch LH.
Monitor item Condition
DOOR SW-RLOPEN :ON
CLOSE :OFF
ALKIA0750ZZ
Te r m i n a l s
Door conditionVoltage (V)
(Approx.) (+)
(–)
BCM
connectorTe r m i n a l
M19 59 GroundOPEN 0
CLOSE
JPMIA0011GB

DLK-70
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR SWITCH
2. Check continuity between BCM connector (A) M19 terminal 59
and rear door switch LH connector (B) B71 terminal 1.
3. Check continuity between BCM connector (A) M19 terminal 59
and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness between BCM and rear door switch LH.
3.CHECK DOOR SWITCH
Check door switch.
Refer to DLK-70, "
REAR LH : Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace rear door switch LH. Refer to XX-XX, "*****"
.
4.CHECK INTERMITTENT INCIDENT
Refer to @@@.
>> INSPECTION END
REAR LH : Component InspectionINFOID:0000000001396547
1.CHECK DOOR SWITCH
1. Turn ignition switch OFF.
2. Check rear door switch LH.
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Replace rear door switch LH. Refer to XX-XX, "*****"
.
REAR RH
BCM connector TerminalRear door switch LH
connectorTerminal Continuity
M19 59 B71 1 Yes
BCM connector Terminal
GroundContinuity
M19 59 No
ALKIA0751ZZ
ALKIA0752ZZ
Te r m i n a l
Door switch condition Continuity
Door switch
1Ground part of door
switchPressed Yes
Released No

DOOR SWITCH
DLK-71
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
REAR RH : DescriptionINFOID:0000000001396548
Detects door open/close condition.
REAR RH : Component Function CheckINFOID:0000000001396549
1.CHECK FUNCTION
With CONSULT-III
Check door switches “DOOR SW-RR” in “Data Monitor” mode with CONSULT-III.
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Refer to DLK-71, "
REAR RH : Diagnosis Procedure".
REAR RH : Diagnosis ProcedureINFOID:0000000001396550
1.CHECK DOOR SWITCH INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check signal between BCM connector and ground with oscillo-
scope.
Is the inspection result normal?
YES >> GO TO 4.
NO >> GO TO 2.
2.CHECK DOOR SWITCH CIRCUIT
1. Disconnect BCM connector.
Monitor item Condition
DOOR SW-RROPEN :ON
CLOSE :OFF
ALKIA0754ZZ
Te r m i n a l s
Door conditionVoltage (V)
(Approx.) (+)
(–)
BCM
connectorTe r m i n a l
M19 60 GroundOPEN 0
CLOSE
JPMIA0011GB

DLK-72
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR SWITCH
2. Check continuity between BCM connector (A) M19 terminal 60
and rear door switch RH connector (B) B53 terminal 1.
3. Check continuity between BCM connector (A) M19 terminal 60
and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness between BCM and rear door switch RH.
3.CHECK DOOR SWITCH
Check door switch.
Refer to DLK-72, "
REAR RH : Component Inspection".
Is the inspection result normal?
YES >> GO TO 4.
NO >> Replace rear door switch RH. Refer to XX-XX, "*****"
.
4.CHECK INTERMITTENT INCIDENT
Refer to @@@.
>> INSPECTION END
REAR RH : Component InspectionINFOID:0000000001396551
1.CHECK DOOR SWITCH
1. Turn ignition switch OFF.
2. Check rear door switch RH.
Is the inspection result normal?
YES >> Door switch is OK.
NO >> Replace rear door switch RH. Refer to XX-XX, "*****"
.
BACK DOOR
BCM connector TerminalRear door switch
RH connectorTerminal Continuity
M19 60 B53 1 Yes
BCM connector Terminal
GroundContinuity
M19 60 No
ALKIA0753ZZ
ALKIA0752ZZ
Te r m i n a l
Door switch condition Continuity
Door switch
1 Ground part of door switchPressed Yes
Released No

DOOR SWITCH
DLK-73
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
C
D
E
F
G
H
I
J
L
MA
B
DLK
N
O
P
BACK DOOR : DescriptionINFOID:0000000001396552
Detects back door open condition.
BACK DOOR : Component Function CheckINFOID:0000000001396553
1.CHECK FUNCTION
With CONSULT-III
Check “BACK DOOR SW” in “Data Monitor” mode with CONSULT-III.
Is the inspection result normal?
YES >> Back door lock assembly (door switch) is OK.
NO >> Refer to DLK-73, "
BACK DOOR : Diagnosis Procedure".
BACK DOOR : Diagnosis ProcedureINFOID:0000000001396554
1.CHECK BACK DOOR LOCK ASSEMBLY (DOOR SWITCH) INPUT SIGNAL
1. Turn ignition switch OFF.
2. Check voltage between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 6.
NO >> GO TO 2.
2.CHECK BACK DOOR LOCK ASSEMBLY (DOOR SWITCH) CIRCUIT
1. Disconnect BCM connector and back door lock assembly.
Monitor item Condition
BACK DOOR SWOPEN : ON
CLOSE : OFF
ALKIA0755ZZ
Te r m i n a l s
Back door
conditionVoltage (V)
(Approx.) (+)
(–)
BCM connector Terminal
M18 10 GroundOPEN 0
CLOSE Battery voltage

DLK-74
< COMPONENT DIAGNOSIS >[WITH I-KEY, WITHOUT SUPER LOCK]
DOOR SWITCH
2. Check continuity between BCM connector (A) M18 terminal 10
and back door lock assembly (door switch) connector (B) D405
terminal 3.
3. Check continuity between BCM connector and ground.
Is the inspection result normal?
YES >> GO TO 3.
NO >> Repair or replace harness between BCM and back door lock assembly.
3.CHECK BACK DOOR LOCK ASSEMBLY GROUND CIRCUIT
Check continuity between back door lock assembly connector and
ground.
Is the inspection result normal?
YES >> GO TO 4.
NO >> Repair or replace back door lock assembly ground circuit.
4.CHECK BCM OUTPUT SIGNAL
1. Connect BCM connector.
ALKIA0756ZZ
BCM connector TerminalBack door lock assembly
(door switch) connectorTerminal Continuity
M18 10 D405 3 Yes
BCM connector Terminal
GroundContinuity
M18 10 No
ALKIA0757ZZ
Back door lock assembly
(door switch) connectorTe r m i n a l
GroundContinuity
D405 4 Yes