button NISSAN TIIDA 2007 Service Workshop Manual

DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
SR-17
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
MA
B
SR
N
O
P
*: If this lamp glows red, the tool is connected to the battery incorrectly.Reverse the connections and check the lamp glows green.
DEPLOYMENT OF AIR BAG MODULE (OUTSIDE OF VEHICLE)
Deployment of Driver Air Bag Module (Outside of Vehicle)
1. Unless the vehicle is being scrapped, deploying the air bag in
the vehicle is not recommended. This may cause damage to the
vehicle interior.
Anchor air bag module bracket (SST: KV99105300) (A) in a vice
secured to a firm foundation deployment.
2. Using wire (B), secure air bag module (1) to air bag module
bracket (SST: KV99105300) (A) at four places.
CAUTION:
 Use wire of at least 1 mm (0.04 in) diameter.
 If a gap exists between air bag module and air bag module
bracket, use a piece of wood (D) inserted in the gap to sta-
bilize the air bag module.
3. Firmly secure air bag module bracket (SST: KV99105300) (A)
with air bag module attached, in a vise (C).
4. Connect deployment tool adapter (SST: KV99110500) (B) to air
bag module (1) and deployment tool connector (SST:
KV99106400) (A).
5. Connect red clip of deployment tool (A) to battery positive termi-
nal and black clip to negative terminal (B).
6. The lamp on the right side of the tool, marked “deployment tool
power”, should glow green, not red.
7. Press the button on the deployment tool (A). The left side lamp
on the tool, marked “air bag connector voltage”, will illuminate
and the air bag module (1) will deploy.
CAUTION:
When deploying the driver air bag module, stand at least 5 m
(16 ft)away from the air bag module.
DEPLOYMENT OF AIR BAG MODULE (OUTSIDE OF VEHICLE)
Deployment of Front Passenger Air Bag Module (Outside of Vehicle)
JMHIA0208ZZ
JMHIA0206ZZ
JMHIA0207ZZ
JMHIA0209ZZ

SR-18
< ON-VEHICLE REPAIR >
DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
1. Firmly secure air bag module bracket (SST: KV99105300) (A) in
a vise.
2. Using wire, secure air bag module to air bag module bracket
(SST: KV99105300) (A) at two places.
CAUTION:
Use wire of at least 1 mm (0.04 in) diameter.
3. Connect deployment tool (SST: KV99106400) (A) and deploy-
ment tool adapter (SST: KV99110500) (B) to front passenger air
bag module connector (1).
4. Connect red clip of deployment tool (A) to battery positive termi-
nal and black clip to negative terminal (B).
5. The lamp on the right side of the tool, marked “deployment tool
power”, should glow green, not red.
6. Press the button on the deployment tool (A). The left side lamp
on the tool, marked “air bag connector voltage”, will illuminate
and the air bag module (1) will deploy.
CAUTION:
 When deploying the front passenger air bag module, do not
stand on the deploying side.
 Stand at least 5 m (16 ft) away from the air bag module.
DEPLOYMENT OF AIR BAG MODULE (OUTSIDE VEHICLE)
Deployment of Side Curtain Air Bag Module (Outside of Vehicle)
JMHIA0208ZZ
JMHIA0210ZZ
JMHIA0211ZZ
JMHIA0209ZZ

DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
SR-19
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
MA
B
SR
N
O
P
1. Cut the inflator (2) from side curtain air bag module (1).
2. Connect deployment tool (SST: KV99106400) (A) and deploy-
ment tool adapter (SST: KV99109800) (B) to the inflator.
3. Put the inflator connected with the deployment tool (SST:
KV99106400) and deployment tool adapter (SST: KV99109800)
into a tire without a wheel.
4. Put the tire with the inflator (1) onto another tire without
wheel.Add an additional tire without a wheel and then a tire
mounted on a wheel on top.
CAUTION:
Tie all tires together with a strap in order keep them stand-
ing.
5. Connect red clip of deployment tool (A) to battery positive termi-
nal and black clip to negative terminal.
6. The lamp on the right side of the tool, marked “deployment tool
power”, should glow green, not red.
7. Press the button on the deployment tool (A). The left side lamp
on the tool, marked “air bag connector voltage”, will illuminate
and the air bag module inflator (1) will deploy.
CAUTION:
When deploying the side curtain air bag module, stand at least 5 m (16ft) away from the side cur-
tain air bag module.
DEPLOYMENT OF AIR BAG MODULE (OUTSIDE VEHICLE)
Deployment of Front Side Air Bag Module (Outside of Vehicle)
JMHIA0064ZZ
JMHIA0065ZZ
PHIA0937J
PHIA1173E

SR-20
< ON-VEHICLE REPAIR >
DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
1. Make 6.5 mm (0.256 in) diameter hole (B) in air bag module
bracket (SST: KV99105300) (A) at the position shown in figure.
2. Firmly secure air bag module bracket in a vise.
3. Insert one bolt through air bag module bracket and air bag mod-
ule upper side holes, and fix them with one M6 bolt/nut.
Insert wire through air bag module bracket and air bag module
lower side holes, and fix them.
CAUTION:
Using wire, of at least 1 mm (0.04 in) diameter.
4. Connect deployment tool (SST: KV99106400) (A) and deploy-
ment tool adapter (SST: KV99109800) (B) to air bag module (1)
connector.
5. Connect red clip of deployment tool (SST: KV99106400) (A),(B)
to battery positive terminal and black clip to negative terminal
(C).
6. The lamp on the right side of the tool, marked “deployment tool
power”, should glow green, not red.
7. Press the button on the deployment tool. The left side lamp on
the tool, marked “air bag connector voltage”, will illuminate and
the air bag module (1) will deploy.
CAUTION:
When deploying the front side air bag module, stand at
least 5 m (16ft) away from the air bag module.
DEPLOYMENT OF SEAT BELT PRE-TENSIONER (OUTSIDE OF VEHICLE)
Deployment of Front Seat Belt Pre-Tensioner (Outside of Vehicle)
1. Firmly grip pre-tensioner (1) in a vise (A) and cut off the web-
bing.
JMHIA0225ZZ
JMHIA0226ZZ
JMHIA0212ZZ
JMHIA0068ZZ

DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
SR-21
< ON-VEHICLE REPAIR >
C
D
E
F
G
I
J
K
L
MA
B
SR
N
O
P
2. Connect deployment tool (SST: KV99106400) (A) and deploy-
ment tool adapter (SST: KV99110500) (B) yellow connector to
front seat belt pre-tensioner (1).
3. Connect red clip of deployment tool to battery positive terminal
and black clip to negative terminal (C).
4. The lamp on the right side of the tool, marked “deployment tool
power”, should glow green, not red.
5. Press the button on the deployment tool. The left side lamp on
the tool, marked “seat belt pre-tensioner connector voltage”, will
illuminate and the seat belt pre-tensioner (1) will deploy.
CAUTION:
When deploying the front seat belt pre-tensioner, stand at
least 5 m(16 ft) away from the seat belt pre-tensioner.
DEPLOYMENT OF SEAT BELT PRE-TENSIONER (OUTSIDE OF VEHICLE)
Deployment of Front Seat Belt Pre-Tensioner2 (Outside of Vehicle)
1. Disconnect the webbing of seat belt pre-tensioner2 (1).
2. Connect deployment tool (SST: KV99106400) (A) and deploy-
ment tool adapter (SST: KV99110500) (B) orange connector to
seat belt pre-tensioner2 (1).
3. Put the seat belt pre-tensioner2 (1) connected with the deploy-
ment tool into a tire without a wheel.
JMHIA0214ZZ
JMHIA0070ZZ
JMHIA0071ZZ
PHIA1288J

SR-22
< ON-VEHICLE REPAIR >
DISPOSAL OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
4. Connect red clip of deployment tool (A) to battery positive termi-
nal and black clip to negative terminal.
5. The lamp on the right side of the tool, marked “deployment tool
power”, should glow green, not red.
6. Press the button on the deployment tool (A). The left side lamp
on the tool, marked “seat belt pre-tensioner2 connector voltage”,
will illuminate and the seat belt pre-tensioner2 (1) will deploy.
CAUTION:
When deploying the front seat belt pre-tensioner2, stand at
least 5 m(16 ft) away from the seat belt pre-tensioner2.
DISPOSING OF AIR BAG MODULE AND SEAT BELT PRE-TENSIONER
Deployed air bag module and seat belt pre-tensioner are very hot. Before disposing of air bag module and
seat belt pre-tensioner, wait at least 30 minutes, and 10 minutes, respectively. Seal them in a plastic bag
before disposal.
CAUTION:
 Never apply water to a deployed air bag module or seat belt
pre-tensioner.
 Wear gloves when handling a deployed air bag moduleor seat
belt pre-tensioner.
 No poisonous gas is produced upon air bag module deploy-
ment. However,be careful not to inhale gas since it irritates
the throat and can cause choking.
 Do not disassemble air bag module and seat belt pre-ten-
sioner.
 Air bag module and seat belt pre-tensioner cannot be reused.
 Wash your hands clean after finishing work.
PHIA1173E
SBF276H

A/T SHIFT LOCK SYSTEM
TM-31
< FUNCTION DIAGNOSIS >[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
A/T SHIFT LOCK SYSTEM
System DescriptionINFOID:0000000001694430
 The mechanical key interlock mechanism also operates as a shift lock:
With the ignition switch turned to ON, selector lever cannot be shifted from “P” position to any other position
unless brake pedal is depressed.
With the key removed, selector lever cannot be shifted from “P” position to any other position.
The key cannot be removed unless selector lever is placed in “P” position.
 The shift lock and key interlock mechanisms are controlled by the ON-OFF operation of the shift lock sole-
noid and by the operation of the rotator and slider located inside key cylinder, respectively.
Component Parts LocationINFOID:0000000001694431
1. Key interlock cable 2. Key cylinder 3. Brake pedal
4. Stop lamp switch
A. Park position switch B. Shift lock solenoid C. Shift lock release button
AWDIA0071ZZ

DIAGNOSIS SYSTEM (TCM)
TM-39
< FUNCTION DIAGNOSIS >[TYPE 1 (4AT: RE4F03B)]
C
E
F
G
H
I
J
K
L
MA
B
TM
N
O
P
4. Turn ignition switch ON. (Do not start engine.)
Does OD OFF indicator lamp come on about 2 seconds?
YES >> GO TO 2.
NO >> Stop procedure. Perform TM-138, "
OD OFF Indicator
Lamp Does Not Come On" before proceeding.
2.JUDGEMENT PROCEDURE STEP 1
1. Turn ignition switch OFF.
2. Keep pressing shift lock release button.
3. Move selector lever from “P” to “D” position.
4. Turn ignition switch ON. (Do not start engine.)
5. Keep pressing overdrive control switch while OD OFF indicator lamp is lighting up for 2 seconds. (OD
OFF indicator lamp is on.)
6. Keep pressing overdrive control switch and shift selector lever to the “2” position. (OD OFF indicator lamp
is on.)
7. Stop pressing overdrive control switch. (OD OFF indicator lamp is on.)
8. Shift selector lever to the “1” position. (OD OFF indicator lamp is on.)
9. Keep pressing overdrive control switch. (OD OFF indicator lamp is off.)
10. Depress accelerator pedal fully while pressing overdrive control switch.
>> GO TO 3.
3.CHECK SELF-DIAGNOSIS CODE
Check OD OFF indicator lamp. Refer to "Judgement of Self-diagnosis Code".
>>DIAGNOSIS END
Judgement of Self-diagnosis Code
SCIA7140E

TM-200
< ON-VEHICLE REPAIR >[TYPE 1 (4AT: RE4F03B)]
SHIFT CONTROL SYSTEM
SHIFT CONTROL SYSTEM
Control Device Removal and InstallationINFOID:0000000001731375
CONTROL DEVICE COMPONENTS
CONTROL CABLE COMPONENTS
1. Selector lever knob 2. Knob cover 3. Lock pin
4. Overdrive control switch 5. Knob finisher 6. Selector button
7. Selector button return spring 8. Position indicator plate 9. Position lamp
10. Dust cover 11. Bracket 12. Shift lock solenoid and park position
switch assembly
13. A/T device harness connector 14. Plate 15. Control device assembly
WCIA0638E

TM-204
< ON-VEHICLE REPAIR >[TYPE 1 (4AT: RE4F03B)]
SHIFT CONTROL SYSTEM
1. Place the selector lever knob (1) in “N” position.
2. Slide knob cover (2) downward.
3. Pull out lock pin (3) from selector lever knob (1).
4. Remove selector lever knob (1) and knob cover (2) as a set from
selector lever.
CAUTION:
Do not push selector button.
INSTALLATION
1. Insert lock pin (1) to selector lever knob (2).
2. Install knob cover (3) to selector lever knob (2).
3. Place the selector lever in “N” position.
4. Install selector lever knob over selector lever until a click is felt.
CAUTION:
 Do not tilt selector lever knob when installing. Install it
straight, and do not tap or apply any shock to install it.
 Do not push selector button.
Adjustment of A/T PositionINFOID:0000000001731378
Move selector lever from “P” position to “1” position. You should be able to feel the detents in each position. If
the detents cannot be felt or if the position indicator is improperly aligned, the control cable needs adjustment.
CAUTION:
Make sure that parking brake is applied before adjustment.
1. Remove the air duct assembly. Refer to EM-27, "
Removal and Installation".
2. Remove the control cable nut (A) and control cable (1) and
place the manual lever (2) in the "P' position.
3. Place selector lever in “P” position.
4. Hold control cable (1) at the end and pull it with a force of 9.8 N
(approximately 1 kg, 2.2 lb). Release the control cable and tem-
porarily tighten control cable nut (A).
5. Tighten control cable nut (A) to the specified torque.
CAUTION:
Secure manual lever when tightening nut.
6. Move selector lever from “P” to “1” position again. Make sure that selector lever moves smoothly.
7. Check A/T position. Refer to TM-204, "
Checking of A/T Position".
8. Install air duct assembly. Refer to EM-27, "
Removal and Installation".
Checking of A/T PositionINFOID:0000000001731379
1. Place selector lever in “P” position, and turn ignition switch ON (Do not start engine).
2. Make sure selector lever can be shifted to other than “P” position when brake pedal is depressed. Also
make sure selector lever can be shifted from “P” position only when brake pedal is depressed.
3. Move selector lever and check for excessive effort, sticking, noise or rattle.
4. Confirm selector lever stops at each position with the feel of engagement when it is moved through all the
positions. Check whether or not the actual position selector lever is in matches the position shown by the
shift position indicator and the transaxle.
SCIA6971E
SCIA6972E
Control cable nut : Refer to TM-200, "Control De-
vice Removal and Installation".WCIA0635E