Peugeot iOn 2018 User Guide
Manufacturer: PEUGEOT, Model Year: 2018, Model line: iOn, Model: Peugeot iOn 2018Pages: 136, PDF Size: 5.79 MB
Page 11 of 136
9
Warning/indicator lampStateCause Action/Observations
Main batter y
charge (normal or
fast) Fixed.
The main battery is being
charged. The lamp goes out once charging is complete.
Flashing. The recharging cable is
connected to the vehicle's
socket, but the main battery is
not being charged. Check the recharging cable connection.
Ancillaries battery
charge Fixed.
The ancillaries battery charging
circuit has a fault (dirty or loose
terminals, converter fault, etc.). The warning lamp should go off when the engine is
started.
If it does not go off, contact a PEUGEOT dealer or a
qualified workshop.
Front seat belt
not fastened/
unfastened Fixed, then flashing,
accompanied by an
audible signal. The driver and/or front
passenger has not fastened or
has unfastened their seat belt. Pull the strap then insert the tongue in the buckle.
Rear right seat
belt unfastened Fixed.
The rear right passenger has
unfastened their seat belt. Pull the strap then insert the tongue in the buckle.
Rear left seat belt
unfastened Fixed.
The rear left passenger has
unfastened their seat belt. Pull the strap then insert the tongue in the buckle.
Airbags Temporarily on. This warning lamp comes on for
a few seconds when you turn on
the ignition, then goes off. If it does not go off, contact a PEUGEOT dealer or a
qualified workshop.
Fixed. One of the airbag or seat
belt pyrotechnic pretensioner
systems has a fault. Have them checked by a PEUGEOT dealer or a
qualified workshop.
Red warning/indicator lamps
1
Dashboard instruments
Page 12 of 136
10
Warning/indicator lampStateCause Action/Observations
Door(s) open/Boot
open Fixed, accompanied
by an audible signal. A door or the boot is still open. Close the door or boot.
Parking brake Fixed. The parking brake is applied or
not properly released. Release the parking brake to switch off the warning
light, keeping your foot on the brake pedal.
Observe the safety recommendations.
For more information on the Parking brake
, refer to
the corresponding section.
Braking Fixed. The brake fluid level has
dropped significantly.
There is a braking assistance
system fault. Stop as soon as it is safe to do so.
Top up with brake fluid approved by PEUGEOT.
If the problem persists, have the system checked by a
PEUGEOT dealer or a qualified workshop.
+ Fixed, associated
with the ABS warning
lamp.
The electronic brake force
distribution (EBFD) system is
faulty. You must stop as soon as it is safe to do so.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
Anti-lock Braking
System (ABS) Fixed.
The anti-lock braking system
has a fault. The vehicle retains conventional braking capabilities.
Drive carefully at reduced speed and contact a
PEUGEOT dealer or a qualified workshop without
d e l ay.
Orange warning/indicator lamps
Dashboard instruments
Page 13 of 136
11
Warning/indicator lampStateCause Action/Observations
+ Fixed.
DSC/ASR systems fault. Have them checked by a PEUGEOT dealer or a
qualified workshop.
Electric power
steering Fixed.
Electric power steering fault. Drive carefully at reduced speed.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
Dynamic stability
control and anti-
slip regulation
(DSC/ASR)
Flashing.
Activation of the DSC/ASR
systems. The systems optimise traction and allow improved
directional stability of the vehicle.
Adapt your driving style and moderate your speed.
Main batter y
protection system Fixed.
The state of charge of the main
battery is insufficient or the
temperature of the main battery is
insufficient. Limited engine power available.
Recharge the main battery as soon as possible.
If the warning lamp does not go off, contact a
PEUGEOT dealer or a qualified workshop.
Fixed.
The DSC/ASR deactivation
button is active.
DSC/ASR is deactivated.
DSC: Dynamic stability control.
ASR: Anti-slip regulation. Press the button to activate the DSC/ASR.
The DSC/ASR system is activated automatically when
the vehicle is started.
1
Dashboard instruments
Page 14 of 136
12
Under-inflationFixed. The pressure in one or more of
the tyres is too low. Check the pressure in the tyres as soon as possible.
This check should preferably be carried out when the
tyres are cold.
You must reinitialise the system after adjusting one or
more tyre pressures and after changing one or more
wheels.
For more information on Tyre under-inflation
detection
, refer to the corresponding section.
Flashing, then fixed. The function is faulty and/or at
least one of the wheels has no
sensor detected. Tyre pressure monitoring is no longer ensured.
Have the system checked by a Peugeot dealer or a
qualified workshop.
Warning/indicator lamp
StateCause Action/Observations
Main electrical
system self-
diagnostic system Fixed.
Fault in the main electrical
system. You must stop as soon as it is safe to do so.
Have it checked by a PEUGEOT dealer or a qualified
workshop.
Passenger's airbag
system Fixed, in the central
console.
The control switch, located in the
glove box or in the central console
(depending on equipment), is set
to the "
OFF" position.
The passenger's front airbag is
deactivated.Set the control switch to the " ON" position to activate
the passenger's front airbag.
In this case, do not install a "rear ward facing" child
seat on the front passenger seat.
Remember to check the status of this control switch
before starting your vehicle.
Rear foglamp Fixed. The rear foglamp has been
switched on using the ring on the
lighting control stalk. Turn the ring on the lighting control stalk to the rear to
switch off the rear foglamp.
Dashboard instruments
Page 15 of 136
13
Warning/indicator lampStateCause Action/Observations
Left-hand direction
indicator Flashing with audible
signal. The lighting control stalk has been moved
down.
Right-hand
direction indicator Flashing with audible
signal. The lighting control stalk has been moved
up.
Hazard warning
lamps Flashing with audible
signal. The hazard warning lamps switch, located
on the dashboard, has been operated.
The left-hand and right-hand direction indicators and
their associated lamps flash simultaneously.
Sidelamps and/
or dipped beam
headlampsFixed.
The sidelamps and/or dipped beam
headlamps have been switched on.
Front foglamps Fixed. The front foglamps have been switched on
using the ring on the lighting control stalk. Turn the ring on the lighting control stalk
twice rear wards to switch off the front
foglamps.
Main beam
headlamps Fixed.
The lighting control stalk has been pulled
towards you. Pull the lighting control stalk to return to
dipped beam headlamps.
Motor braking
reduction Flashing.
The main battery is fully charged, the motor
braking is temporarily reduced. Anticipate when you need to brake: use
the brake pedal to slow down or stop the
vehicle.
Ready
(ready to drive)
Fixed, accompanied by
an audible signal when
it comes on.The vehicle is ready to drive, you can
operate the accelerator now.
The lamp stays on as long as the vehicle is
powered up.
Green warning/indicator lamps
Black warning/indicator lamps Blue warning/indicator lamps
1
Dashboard instruments
Page 16 of 136
14
Main battery state of
charge indicator
Display
The state of charge of the main battery is
displayed continuously in the instrument panel.
Low energy alerts
Four successive energy level alerts indicate
that the energy available in the main battery
has dropped to a low level:
-
2 l
it and flashing bars on the energy gauge
in the instrument panel: starting to use the
reserve.
-
T
he final bar on the energy gauge flashes.
-
T
he final bar disappears: the range
display disappears, the heating and air
conditioning are cut off. -
D
isplay of this warning lamp
in the instrument panel:
progressive reduction in
available engine power.
Energy consumption/
generation indicator
System informing the driver of the level of
energy consumption or generation by the main
battery.
"Neutral" position
On switching on the ignition, your vehicle
neither consumes nor generates energy
through its electric drive train: the needle is in
the "neutral" position (provided the heating and
air conditioning are off).
Energy consumption
The needle moves to the right, in proportion to
the consumption of energy by the vehicle.
"Eco" zone
The needle is in this zone when the vehicle is
used in a way that limits the consumption of
electric energy and optimises its range.
Dashboard instruments
Page 17 of 136
15
In cold weather, the capacity to regenerate
through braking is reduced.
Total distance recorder "Charge" zone
The needle moves to the left, in proportion to
the level of charge going into the main battery,
during periods of deceleration and braking.
Instrument panel display
screen
When the switch is in the "ON" position, you
can display various information on the screen
by successively pressing button A .
System which measures the total distance
travelled by the vehicle during its life. Press button A
.
The total distance appears in the display.
Switching the speedometer unit
When the total distance recorder is displayed,
hold button A down for a few seconds to
change the speedometer unit (mph or km/h).
When remaining range indicator is displayed in
the unit (miles or km) corresponding to that of
the speedometer unit (mph or km/h).
Trip distance recorder
(trip
A o
r B)
These two trips indicate the distance travelled
since the trip recorder was last reset. Press button A to display the desired trip.
Reset
With the ignition on, when one of the trips A or
B is displayed, press the button for more than
two seconds.
1
Dashboard instruments
Page 18 of 136
16
Lighting dimmer
System that allows the brightness of the
instruments and controls to be adjusted
manually to suit the ambient light level.
With the headlamps on or off, press button A to
select the function, then hold it down to adjust
the brightness of the instruments and controls
lighting to "day" or "night".
The brightness of the lighting increases every
time you press button A.
When the lighting reaches the maximum
setting, press again to move to the minimum
setting.
Release button A as soon as the lighting
reaches the desired brightness.
The setting is registered as soon as you
release button A and is stored when the ignition
switch is turned to OFF.
Service indicator
System which informs the driver when the
next ser vice is due, in accordance with the
manufacturer's servicing schedule.
This due date is calculated from the last reset
of the service indicator.
There are two different ways to indicate when
the next ser vice is due:
-
r
emaining distance (in kilometres or miles),
-
t
ime (in months) left before the next
service.
Once the ignition is switched on, press
button
A successively until the ser vice indicator
is displayed in the desired units.
Operation
1. The display shows the distance or time
remaining before the next service.
2. The display shows that the ser vice is due.
Each time the ignition is switched on, the
ser vice spanner is displayed for a few
seconds to notify you that the ser vice
must be carried out very soon.
3. Once the ser vice has been completed,
the distance or the time remaining before
the next ser vice is displayed.
Dashboard instruments
Page 19 of 136
17
Resetting the service indicator
After each service, the service indicator must
be reset to zero.
The procedure for resetting to zero is as
follows:
F
T
urn off the ignition (switch to LOCK or
ACC position).
F
P
ress the reset button A in succession until
the service indicator is displayed.
F
P
ress and hold the reset button down for a
few seconds to make the spanner flash .
F
P
ress the reset button whilst the spanner
is flashing to move the display " ---" to
" CLEAR ".
The distance (or the time) remaining before
the next ser vice is displayed. The distance "
---" indicating that the
ser vice is now due is reset automatically
after a certain time and a certain distance
travelled. The display will then indicate the
remaining time before the next service.
Under-inflation detection
You must reinitialise the under-inflation
detection system after adjusting one or more
tyre pressures and after changing one or more
wheels.
The procedure for this is as follows.
F
P
ress button A to select the system.
F
P
ress and hold button A down for at least
three seconds .
An audible signal sounds and the under-
inflation warning lamp flashes slowly until
reinitialisation has been completed.
1
Dashboard instruments
Page 20 of 136
18
Choice of set of tyres fitted
If you have registered a second set of tyres
with sensor, after every change, select the
corresponding set in the instrument panel
display screen.
The procedure for this is as follows.
F
P
ress button A to select the system.
F
P
ress and hold button A for more than ten
seconds to move from tyre set 1 to tyre
set
2 in succession or vice versa.
Range indicator
This function provides you with an estimated
range that your vehicle can still travel, taking
into account your recent conditions of use
(driving style, use of heating, air conditioning,
e t c .) .When the remaining range is too low, " ---"
is displayed in the instrument panel.
The remaining range can be displayed in
miles or kilometres.
For more information on the distance
recorder , and the unit change in
particular, refer to the corresponding
section.
Dashboard instruments