ignition Peugeot RCZ 2014 Repair Manual

184
Changing reversing lamp and foglamp bulbs
(1.6 litre THP 270 hp version)
The bulbs on these two types of lamp are changed by partly removing
the lamp unit A in the rear bumper:
 using a screwdriver, remove the 3 fi xing screws B located under the
vehicle,
Take care not to touch the silencer; risk of burns, if you
change the bulb immediately after switching off the ignition.
 without forcing, lower the rear part of the lamp unit for access to the \
bulb holders C ,
 turn the corresponding bulb holder a quarter of a turn then remove it towards the front of the vehicle,
 turn the bulb one quarter of a turn and change it.
To refi t, carry out these operations in reverse order.

186
CHANGING A FUSE
ACCESS TO THE TOOLS
The extraction tweezer is fi tted to the back of the dashboard fusebox
cover.
To gain access to them:
 turn the screw a quarter of a turn to the left,
 unclip the cover by pulling at the top right,
 remove the cover completely and turn it over,
 remove the carrier on which is fi tted the tweezer.
CHANGING A FUSE
Before changing a fuse, tit is necessary to:
 identify the cause and correct it,
 switch off all electrical consumers,
 immobilise the vehicle and switch off the ignition,
 identify the failed fuse using the allocation tables and drawings presented on the following pages.
To replace a fuse, you must:
- use the special tweezer to extract the fuse from its housing and check the condition of its fi lament,
- always replace a failed fuse with a fuse of the same rating (same colour); a different rating fuse may cause malfunctions (risk of fi re).
Good Failed
Tweezer
If the fault recurs soon after changing a fuse, have the electrical
system of your vehicle checked by a PEUGEOT dealer or a
qualifi ed workshop.

188
DASHBOARD FUSES
The fusebox is placed in the lower section of the dashboard (left-hand \
side). It consists of two boxes.
Access to the fuses
 Refer to the paragraph "Access to the tools".
Fuse tables
Fuse N° Rating Functions
F2 30 A Locking and deadlocking earth.
F3 5 A Airbags, active bonnet and pretensioners
control unit.
F4 10 A Clutch pedal switch, electrochromatic
rear view mirror, automatic gearbox,
switching and protection unit.
F5 30 A One-touch electric windows, folding door
mirrors supply.
F7 5 A Front and rear courtesy lamps, map
reading lamps, sun visor lighting, glove
box lighting.
F8 20 A Audio equipment, audio/telephone,
multifunction screen, tyre under-infl ation
detection, clock.
F9 30 A 12 V socket.
F10 15 A Steering mounted controls.
F 11 15 A Low current ignition switch.
F12 15 A Instrument panel, air conditioning,
driver's seat memory unit, rain /
sunshine sensor, airbags.
Box 1

194
TOWING YOUR VEHICLE
Towing from the front
 On the front bumper, unclip the cover by pressing on the left.
 Screw the towing eye in fully.
 Install the towing bar.  Place the gear lever in neutral (position N for an automatic
gearbox).
Failure to observe this instruction could result in damage to certain components (braking, transmission...) and the
absence of braking assistance the next time the engine is
started.
 Unlock the steering by turning the ignition key one notch and release the parking brake.
 Switch on the hazard warning lamps on both vehicles.
 Move off gently and drive slowly and for a short distance only.
Towing from the rear
It is also possible to pull your vehicle from the rear, but only in
exceptional circumstances (vehicle in a parking space, off the road...).
 On the rear bumper, unclip the cover by pressing on the left.
 Screw the towing eye in fully.
 Install the towing bar.
 Place the gear lever in neutral (position N for an automatic
gearbox).
 Switch on the hazard warning lamps on both vehicles.
 Move off very gently to pull the vehicle out.
* Except 1.6 litre THP 270 hp version.
TOWING ANOTHER VEHICLE *
 On the rear bumper, unclip the cover by pressing on the left.
 Screw the towing eye in fully.
 Install the towing bar.
 Switch on the hazard warning lamps on both vehicles.
 Move off gently and drive slowly and for a short distance only.

208
EMERGENCY OR ASSISTANCE CALL
In an emergency, press this button for more than 2 seconds. Flashing of the green LED and a voice message confi rm that the call has been made to the "PEUGEOT Connect SOS" centre * .
The green LED remains on (without fl ashing) when communication is established. It goes off at the end of communication.
When the ignition is switched on, the green LED comes on for 3 seconds indicating that the system is operating correctly.
Pressing this button again immediately cancels the request.
The cancellation is confi rmed by a voice message.
Press this button for more than 2 seconds to request assistance if the vehicle breaks down.
A voice message confi rms that the call has been made ** .
Pressing this button again immediately cancels the request. The green LED goes off. Cancellation is confi rmed by a voice message.
To cancel a call, tell the "PEUGEOT Connect SOS" call centre that the call was a mistake.
"PEUGEOT Connect SOS" immediately locates your vehicle, starts communication with you in your language ** , and where necessary sends the appropriate public emergency services ** . In countries where the service is not available, or when the locating service has been expressl\
y declined, the call sent directly to the emergency services (112) without the vehicle location.
If an impact is detected by the airbag control unit, and independently of the deployment of any airbags, an emergency call is made automatically.
* Subject to the general conditions for the service available from dealers\
and to technological and technical limitations.
If the orange LED fl ashes: there is a system fault.
If the orange LED is on continuously: the backup battery must be replaced.
In either case, contact a PEUGEOT dealer.
If you purchased your vehicle outside the PEUGEOT dealer network, we invite you to have a dealer check the confi guration of these services and, if desired, modifi ed to suit your wishes. In a multi-lingual country, confi guration is possible in the offi cial national language of your choice.
For technical reasons and in particular to improve the quality of "PEUGEOT CONNECT services" services to customers, the manufacturer reserves the right to carry out updates to the vehicle's on-board telema\
tic system.
PEUGEOT Connect SOS PEUGEOT Connect Assistance
Operation of the system
** Depending on the geographical cover of "PEUGEOT Connect SOS", "PEUGEOT Connect Assistance" and the offi cial national language selected by the owner of the vehicle.
The list of countries covered and PEUGEOT CONNECT services services is available from dealers or at www.peugeot.co.uk.

07
MEDIA
2ABC3DEF5JKL4GHI6MNO8TU V7PQRS9WXYZ0*#
1RADIOM EDIA NA
V ESC TRAFFIC
SETUPADDR
BOOK
2AB C3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
RADIO NA
V TRAFFICMEDIA
236
Select "Jukebox management" then "Add fi les" and press OK at each step to confi rm.
Press the MEDIA button. Press the MEDIA button again or select Media Menu and press OK to confi rm.
Insert an audio / MP3 CD, a USB memory stick or an SD card.
Jukebox
Add fi les
Check that the active MEDIA source is that of the medium used (CD, USB or SD card).
Select "Add fi les from MP3-Disc" for example and press OK to validate.
Select the tracks required then "Rip selection" or select all of the tracks using "Rip all".
Select "[New folder]" to create a new folder or select an existing folder (created previously).
Add fi les from MP3-Disc
[New folder]
"Do you want to change the names of the tracks that will be ripped?": select "Yes" to change them or "No".
To copy an MP3 CD, then select "Real time ripping", "Fast ripping" / "High quality (192 kbit/sec)" or "Standard quality (128 kbit/sec)" then select "Start ripping".
Confi rm the warning message by pressing "OK" to start the copy.
OK
Ye sNo
When copying is in progress, switching off the ignition will interrupt the process but it will resume directly when the ignition is switched on aga\
in.
MUSIC MEDIA PLAYERS
Copying a CD, a USB memory stick or an SD card to the hard disk

08
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
240
* The services available via the telephone depend on the network, the SIM \
card and the compatibility of the Bluetooth device used. Refer to your telephone's manual and your operator to check which services you have access to.
USING THE TELEPHONE
Pairing a Bluetooth telephone /
First connection
For safety reasons and because they require prolonged attention on the p\
art of the driver, the operations for pairing the Bluetooth mobile telephone to the hands-free system of the PEUGEOT Connect Media Navigation (NG4 3D) PEUGEOT Connect Media Navigation (NG4 3D) PEUGEOTmust be carried out with the vehicle stationary and the ignition on. Visit www.peugeot.co.uk for more information (compatibility, more help, ...).
Activate the telephone's Bluetooth function and ensure that it is "visible to all" (refer to the telephone instructions).
If no telephone has been paired, the system prompts you to "Connect phone". Select "Yes" and press OK to confi rm.
Enter the authentication code on the telephone. The code to be entered is displayed on the screen of the system.
To pair another telephone, press the TEL button, then select Phone menu, then "Select phone" then "Connect Bluetooth phone" then select the telephone required.
Press OK at each step to confi rm.
Once the telephone has been connected, the PEUGEOT Connect Media Navigation (NG4 3D) can synchronise the address book and the call list. This synchronisation may take a few minutes * .
Pairing can be started from the telephone (refer to the telephone instructions).
Press the CALL button.
Select "Search phone" and press OK to confi rm. Then select the name of the telephone.
Search phoneSearch phone
To delete a pairing, press TEL, select "Connect phone" then "Delete pairing".

08
2ABC3DEF5JKL4GHI6MNO8TUV7PQR S9WXYZ0*#
1RADIO MEDIA NA
V TRAFFIC
SETUPADDR
BOOK
241
* The services available via the telephone depend on the network, the SIM card and the compatibility of the Bluetooth device used. Refer to * The services available via the telephone depend on the network, the SIM card and the compatibility of the Bluetooth device used. Refer to * The services available via the telephone depend on the network, the
your telephone's manual and your operator to check which services you SIM card and the compatibility of the Bluetooth device used. Refer to your telephone's manual and your operator to check which services you SIM card and the compatibility of the Bluetooth device used. Refer to
have access to. A list of mobile telephones which offer the best range of your telephone's manual and your operator to check which services you have access to. A list of mobile telephones which offer the best range of your telephone's manual and your operator to check which services you
services is available from dealers. have access to. A list of mobile telephones which offer the best range of services is available from dealers. have access to. A list of mobile telephones which offer the best range of
USING THE TELEPHONE
Connecting a Bluetooth telephone
For safety reasons and because they require prolonged attention on the part of the driver, the operations for pairing the Bluetooth mobile telephone to the hands-free system of the PEUGEOTConnect Media Navigation (NG4 3D) must be carried out with the vehicle stationary and the ignition on.
Activate the telephone's Bluetooth function and ensure that it is visible to all.
Once the telephone has been connected, the PEUGEOT Connect Media Navigation (NG4 3D) can synchronise the address book and the call list. This synchronisation may take a few minutes * .
Press the PICK UP button.
The list of telephones connected previously (maximum of 4) appears in the multifunction screen. Select the telephone required then select "Connect phone" for a new connection. Select "Delete pairing" to cancel the connection to the telephone.

06
279
USING THE TELEPHONE
Select " Connect " and confi rm.
The system offers to connect the telephone:
- in " Hands-free mode " (telephone only),
- in " Audio " mode (streaming: playing music fi les on the telephone),
- or " All " (for selection of both modes).
Select " OK " and confi rm.
Then accept automatic connection on the telephone to allow the telephone to reconnect automatically every time the vehicle is started.
The ability of the system to connect in only one mode depends on the telephone. The two modes may both connect by default.
The " Hands-free mode " should be used in preference if "Streaming" is not desired.
The services available depend on the network, the SIM card and the compa\
tibility of the Bluetooth telephone used. Check the telephone manual and with your network provider for details of the services availa\
ble to you.
Depending on the type of telephone, the system will ask you to accept or not the transfer of your contacts.
On return to the vehicle,the last telephone connected automatically reconnects, within around 30 seconds after switching on the ignition (Bluetooth activated and visible).
To modify the automatic connection mode, remove the pairing and pair the telephone again with the desired mode.
Enter a minimum 4 fi gure code in the telephone and confi rm.
Enter the same code in the system, select " OK " and confi rm.
Select the name of the desired peripheral from the list of devices detected then confi rm

08
293
Insert the CD in the player, insert the USB memory stick in the USB player or connect the USB peripheral to the USB port using a suitable cable (not supplied)
The system builds playlists (in temporary memory), an operation which can take from a few seconds to several minutes at the fi rst connection.
Reduce the number of non-music fi les and the number of folders to reduce the waiting time.
The playlists are updated every time the ignition is switched off or connection of a USB memory stick. However, the system memorises these lists and if they are not modifi ed, the loading time will be shorter.
Play starts automatically after a period which depends on the capacity of the USB memory stick.
Selection of source
The SOURCE button on the steering mounted controls allows a direct change to the next media source.
" CD / CD MP3 "
" USB, iPod "
" AUX " " STREAMING "
" RADIO "
Press MUSIC to display the " MEDIA " menu.
Select " Following media source " and confi rm.
Repeat the operation as many times as necessary to obtain the desired media source (except for radio which is accessible either with SOURCE or RADIO ).
Sources
MUSIC MEDIA PLAYERS