lock RENAULT KANGOO 1997 KC / 1.G Electrical Equipment User Guide

IMMOBILISER
Coded key immobiliser system
82
13063R
Track Allocation
A1 Courtesy light timer*
A2 Antenna ring coded connection
A3 Diagnostic socket information (line K)
A4 Diagnostic socket information (line L)
A5 Red immobiliser warning light
A6 Coded information to injection computer
or coded solenoid valve
A7 + after ignition
A8 Earth
A9 + before ignition
B1 Infrared input*
B2 Door lock command*
B3 Not used
B4 Door switch*
B5 Door open command*
B6 Not used
B7 Not used
B8 Door open*
B9 Door lock*
DECODER UNIT CONNECTIONS (fullest version)
* Vehicle with remote control
82-14

IMMOBILISER
Coded key immobiliser system
82
KEY
104 Ignition switch
120 Injection computer
123 Door locking button
138 Rear right door locking motor
140 Driver’s door locking motor
141 Passenger’s door locking motor
142 Luggage compartment door locking motor
154 Luggage compartment door switch
178 Rear right door switch
180 Driver’s door switch
181 Passenger’s door switch
213 Courtesy light
225 Diagnostic socket
247 Injection warning light and red immobiliser
warning light on instrument panel
249 Remote control receiver
260 Passenger compartment fuse box
503 Decoder unit
711 Coded solenoid valveFAULT FINDING
If this immobiliser system is faulty, fault finding
may be carried out using the XR25.
CONNECTION
Use cassette no° 17 and the corresponding fault
finding fiche no° 56.
92656S2
Connect the XR25 to the diagnostic socket.
Position the ISO selector on S8.
Enter the code for the immobiliser system D56.
NOTE : For information on the interpretation of
the bargraphs, the fault charts, checking confor-
mity and additional tests, refer to the fault fin-
ding section.
82-16

INSTRUMENT PANEL
Instrument panel
83
DESCRIPTION
- electronic speedometer,
- display : mileometer/trip recorder and clock
- coolant temperature gauge,
- fuel gauge,
- warning light functions.
13054S
1 Trip mileometer reset button and clock reset (rotate).
NOTE :
• Under normal operating conditions, the oil level is only measured if the ignition has been switched off for
over one minute; otherwise the old oil level value is re-displayed.
If a fault is detected, however, an oil level measurement is made each time the ignition is switched on to
check if the fault is persisting.
• It is normal to find that the oil level is not always the same:
- parking on a slope,
- too short a wait after running the engine for a short moment (especially when the oil is cold), ...
83-7

INSTRUMENT PANEL
Fuel level sensor
83
97163R7
Tighten the mounting nut on the fuel and sender
unit assembly to a torque of 3.5 daN.m using the
tool Mot. 1264-01, holding the sender unit to pre-
vent it from rotating.
Make sure that the connector is firmly locked and
that the quick-release unions are securely clipped
on (with 2 O-ring seals)
Reconnect the battery.
CONNECTION
Disconnect the connector and the pipes on the
sender unit side.
Remove the mounting nut (5) of the pump and
sender unit using tool Mot. 1264-01.
Slacken the nut, remove the tool, unscrew the nut
by hand and remove it.
Remove the pump and sender unit assembly.
NOTE : If several hours may pass between
removing and refitting the pump and sender unit
assembly, refit the nut to the fuel tank to prevent
it from distorting.
REFITTING OF THE PUMP AND SENDER UNIT
ASSEMBLY
Special notes
Check that the seal is in good condition and re-
place it if necessary.
Fit the seal on the fuel tank first before fitting the
assembly.
Refit the pump and sender unit assembly in the
fuel tank by aligning it so that the indexing arrow
(F) is positioned in line with the longitudinal axis
of the vehicle, pointing towards the rear of the
vehicle.
DI8307
Track Allocation
A1 Earth
A2 Low fuel level warning light
B1 Sender unit information to instrument
panel
B2 Not used
C1 + pump
C2 - pump
Checking
IndicationValue between
terminals
A1 and B1 (in Ω)
4/4 7 maximum
3/4 54.5 ± 7
1/2 98 ± 10
1/4 155 ± 16
Low fuel 300 ± 20
97162S
83-11

INSTRUMENT PANEL
Oil level sensor
83
98898R1
OPERATION
The sensor consists of a wire with a high
coefficient of resistance. When a current passes
through the wire it does not have the same
thermal conductivity when it is immersed in a
liquid as when it is in the open air.
After a fixed time a voltage difference is obtained
at the sensor terminals depending on the depth of
immersion of the wire. This voltage difference is
recorded by the electronic unit which manages
the level display function and also controls the
"low oil level" warning light display on the
central liquid crystal display.
When the ignition is switched on, the central dis-
play shows the oil level in a series of "blocks" for
approximately 30 seconds, before returning to
displaying the trip mileometer and total mileome-
ter functions (or "odometer" function).
NOTE : Turning the trip mileometer reset button
before the end of the timed period will display
the "odometer" function.
LOOKING FOR FAULTS
If a short circuit or an open circuit is detected
when the oil level is measured, the display will im-
mediately show the trip mileometer / clock dis-
plays.
CHECKING
The sensor resistance must be between 6 and 20
ohms.
The sensor is deemed to be in short circuit for a va-
lue lower than 4 ohms.
The sensor is deemed to be in open circuit for a va-
lue higher than 22 ohms.
LOCATION
Example : F engine
83-12

CONTROLS - SIGNALS
Stalk mounting
REMOVAL - REFITTING
Disconnect the battery and set the wheels
straight.
Remove the steering wheel and the two half cow-
lings (for vehicles with an airbag, refer to the re-
moval of the rotary switch on the following page
or section 88 for special notes on removing the
steering wheel).
Special notes for vehicles with an airbag
Before removing the assembly, the position of the
rotary switch under the steering wheel must be
noted:
- by ensuring that the wheels are straight on re-
moval so that the strip may be positioned in the
centre,
- by immobilising the rotary switch rotor using
adhesive tape.
Slacken the bolt (C) then sharply tap the screwdri-
ver to release the cone.
84
Special notes for refitting
Fit the mounting with its components, connect
the various connectors and push the assembly
back against the steering column.
Continue refitting and do not lock bolt (C) until
the two half cowlings are refitted, so that the
stalks may be aligned with the dashboard and the
instrument panel.
This operation is made easier by a cut-out section
giving access to bolt (C) in the lower half cowling.
For vehicles with an airbag, observe the re-
commendations in the section " Special notes for
the rotary switch under the steering wheel" on
the following page or section 88 (driver’s airbag).
12970R2
Move the stalk mounting assembly back slightly
and disconnect the connectors.
84-3

CONTROLS - SIGNALS
Rotary switch under steering wheel
This makes the electrical connection between the
steering column and the steering wheel.
It consists of a strip of conductor tracks (airbag)
whose length is designed to guarantee 2.5
steering wheel turns (steering lock plus safety
margin) on each side.
REMOVAL - REFITTING
84
- the horn connector, if fitted,
- the steering wheel bolt,
- the steering wheel after setting the wheels
straight,
- the half cowlings (3 bolts).
Disconnect the connector for the rotary switch
and remove it after removing the three mounting
bolts (E).
Before removing the rotary switch its position
must be noted:
- by ensuring that the wheels are straight on re-
moval so that the track may be positioned in
the centre,
- by immobilising the rotary switch rotor using
adhesive tape.
If it is being replaced, the new part is supplied rea-
dy centred by an adhesive label which will tear off
as soon as the steering wheel is turned for the first
time (fit with the wheels straight).
12970R3
Disconnect the battery.
Remove:
- the airbag cushion by the two torx T30 bolts
(tightening torque : 0.5 daN.m) located behind
the steering wheel and disconnect the connec-
tor (D),
IMPORTANT: It is not permitted to operate the
pyrotechnical systems (airbags and pretensioners)
near a source of heat or flame as there is a risk of
triggering.
IMPORTANT : If the steering wheel is removed,
the airbag connector (D)
MUST be disconnected.
The airbag has a connector which short circuits if
it is disconnected to prevent incorrect triggering.
12973R
84-4

WIRING
Remote control for door locking
88
.GENERAL
These vehicles are equipped with an infrared or
radio frequency remote control with rolling code,
which prevents the code from being copied.
When a transmitter is replaced it will therefore be
necessary to resynchronise it so that the transmit-
ters are returned to phase with the decoder unit.
This remote control is only used for locking and
unlocking the opening elements (it has no effect
on the immobiliser).
IMPORTANT: this system cannot operate with
three remote controls (the decoder unit can only
manage two different rolling codes).
THE TRANSMITTER (PLIP)
Replacing or adding a remote control with immo-
biliser function without replacing the decoder
unit.
Order a spare key head using the number in the
head of one of the old keys or the label normally
attached to the keys when the vehicle is delivered
(eight alphanumeric characters).
If a key is being added or has been lost, remember
to order the insert with the key number.
Carry out the special resynchronisation procedure
using the XR25.
This procedure resets the remote control into se-
quence with the decoder unit (rolling code) and
should only be used if the decoder unit is not
being replaced (with immobiliser only).
1.Ignition off, connect the XR25 (ISO selector on
S8, code D56).
For vehicles fitted with an infra-red remote
control, enter command mode G04* (forced
protection mode) then switch the ignition on
again and enter the vehicle’s security code
(see procedure in section 82).
For vehicles fitted with a radio frequency re-
mote control, go to point 2.
2.Switch the ignition off and enter command
mode G32*.
From this moment, the operator has 10 se-
conds to carry out the next operation.
NOTE: The 10 seconds are shown by the illu-
mination of the red immobiliser warning light
and bargraph 17 LH on the XR25
(code D56,
fiche n° 56).
3.Press the remote control twice (the doors lock
and unlock and the red warning light extin-
guishes).
NOTE :
- When replacing a key head, resynchronisa-
tion of the second remote control (if fitted)
is not always necessary.
Check that the second control operates,
otherwise resynchronise it.
- If both remote controls (if fitted) are desyn-
chronised, two resynchronisation proce-
dures will have to be carried out (one for
each remote control).
IMPORTANT: To ensure that the infrared code
is correctly transmitted it is essential to direct
the transmitter correctly towards the receiver.
If the procedure fails it will be necessary to
restart from the beginning (infrared remote
control only).
4.The procedure is complete - check that the
doors lock correctly.
88-3

WIRING
Remote control for door locking
88
Replacing or adding a remote control without im-
mobiliser function without replacing the decoder
unit.
If the vehicle does not have an immobiliser, the re-
mote control does not have a special number. A
key head without a number may therefore be or-
dered.
If a key is being added or has been lost, remember
to order the insert with the key number.
Carry out the special resynchronisation procedure
using the XR25.
This procedure resets the remote control into se-
quence with the decoder unit (rolling code) and
should only be used if the decoder unit is not
being replaced (with immobiliser only).
1.Ignition off, connect the XR25 (ISO selector on
S8, code D56).
2.Enter command mode G32* (the doors lock
and unlock).
From this moment, the operator has 10 se-
conds to carry out the next operation.
NOTE: The 10 seconds are shown by the illu-
mination of bargraph 17 LH on the XR25
(code
D56,
fiche n° 56).
3.Press the remote control twice (the doors lock
and unlock).
NOTE :
- When replacing a key head, resynchronisa-
tion of the second remote control (if fitted)
is not always necessary.
Check that the second control operates,
otherwise resynchronise it.
- If both remote controls (if fitted) are desyn-
chronised, two resynchronisation proce-
dures will have to be carried out (one for
each remote control).
IMPORTANT: To ensure that the infrared code
is correctly transmitted it is essential to direct
the transmitter correctly towards the receiver.
If the procedure fails it will be necessary to
restart from the beginning (infrared remote
control only).
4.The procedure is complete - check that the
doors lock correctly.
Simple resynchronisation procedure
This procedure allows the remote controls to be
reset with the decoder unit (rolling code).
This procedure is used:
- when the remote control code no longer lies
within the reception range of the decoder unit
(over 1,000 consecutive presses on the remote
control, away from the vehicle).
- when replacing a decoder unit alone (new de-
coder unit),
- when replacing a remote control if the decoder
unit is new (replacing a kit).
REMINDER: when replacing or adding a remote
control with immobiliser function without repla-
cing the decoder unit, refer to "Replacing or ad-
ding a remote control with or without immobili-
ser function without replacing the decoder unit"
(specific resynchronisation procedure).
88-4

WIRING
Remote control for door locking
88
Ignition off:
1.Press and hold the central door locking button
for a few seconds until the doors lock and un-
lock.
From this moment, the operator has 10 se-
conds to carry out the next operation.
NOTE: The 10 seconds are shown by the illu-
mination of the red immobiliser warning light
(if fitted) and bargraph 17 LH on the XR25
(code
D56, fiche n° 56).
2.Press the remote control twice (the doors lock
and unlock and the red warning light extin-
guishes, if fitted).
NOTE : If both remote controls (if fitted) are
desynchronised, two resynchronisation proce-
dures will have to be carried out (one for each
remote control).
IMPORTANT: To ensure that the infrared code
is correctly transmitted it is essential to direct
the transmitter correctly towards the receiver.
If the procedure fails it will be necessary to
restart from the beginning (infrared remote
control only).
3.The procedure is complete - check that the
doors lock correctly.
Removal - Refitting
The dashboard must be partially removed to re-
move the decoder unit.
Remove:
- the steering wheel with the wheels straight,
- the half cowlings under the steering wheel,
- the knee protector under the steering column,
- the lights and wiper controls,
- the instrument panel surround,
- the instrument panel,
- the ashtray, its mounting and the two dash-
board mounting bolts on the heating unit,
- the trim at the bottom of the dashboard on the
driver’s side,
- the two speaker grilles on the dashboard,
- the dashboard mountings.
THE DECODER UNIT
The decoder unit is located in the left hand side of
the dashboard (A).
12967R
88-5