check engine RENAULT KANGOO 1997 KC / 1.G Foult Finding - Injection User Guide

DPCF01 1.0
LUCAS DIESEL INJECTION
Fault finding - Interpretation of XR25 bargraphs13
AFTER REPAIRErase the computer memory (G0**), switch the ignition off, then carry out a road
test.
Finish the operation by checking using the XR25.
Bargraph 12 RH illuminated
Full load or no load not programmed12
None NOTES
Programme the full load position of the accelerator pedal using command G31* (do not adjust the load
lever directly).
Enter code G31* on the XR25 (engine speed zero).
- Press the accelerator pedal when the display flashes "PF".
The display then shows "bon", "Fin" then "6/7.dIE" when the procedure has been completed correct-
ly. Bargraph 12 RH side must be extinguished.
- Switch off the ignition.
Fiche n° 60 1/2
13-25

DPCF01 1.0
LUCAS DIESEL INJECTION
Fault finding - Interpretation of XR25 bargraphs13
AFTER REPAIRErase the computer memory (G0**), switch the ignition off, then carry out a road
test.
Finish the operation by checking using the XR25.
Bargraph 13 LH flashing (cc.1)
Air conditioning cut out information circuit
XR25 aid:*13 :cc.1 : Short circuit to 12 volts
13
None NOTES
Fiche n° 60 1/2
cc.1
Ensure insulation in relation to 12 volts of the connection between track 19 on the computer connector
and track 18 on the air conditioning computer connector.
Test the connections on the 2 connectors (+ intermediate connection engine / dashboard).
Even if present at the moment of testing, this fault is still declared
by a flashing BG 13LH side. To confirm its presence and the necessity
of following the fault finding below, erase the computer memory
then start the engine. The fault is present if the bargraph flashes
when the engine is running.
NOTES
If the fault persists after these tests, replace the air conditioning control module.
If the "air conditioning cut out information "fault reappears, replace the diesel injection computer (consult
the "Aid" section for this operation).
13-26

DPCF01 1.0
LUCAS DIESEL INJECTION
Fault finding - Checking conformity
13
Engine cold, ignition onNOTES
Order of
operationsFunction to check Action Bargraph Display and notes
1 Dialogue with XR25D34
(selector on
S8) 6. dlE
Use fiche n° 60
fault test side
2Interpretation of
normally illuminated
bargraphs Fault test
Code present
3 Change to status test
modeG01* 7. dlE
Use fiche n° 60
status test side
4 Interpretation of
normally illuminated
bargraphs
Code present
Advance corrector fed
Illuminated if command mode
G0** has been used since the
last dialogue took place
Fault warning light fed
Illuminated in preheating
phase
Injection computer may give
load lever position to other
computers (not used)
Injection computer may give
engine speed information to
other computers (not used)
1
1
1
2
11
4
11
10
10
13-32

DPCF01 1.0
LUCAS DIESEL INJECTION
Fault finding - Checking conformity
13
Engine cold, ignition onNOTES
Order of
operationsFunction to check Action Bargraph Display and notes
5Computer
configuration
With AC
Without ACG50*3*
G50*8*
G50*4*
G50*9*With AC
With PAS with pump
Without AC
With conventional PAS
6Absolute pressure
sensor#16 X = local atmospheric pressure
7Coolant temperature
sensor#02 X = Ambient temperature
± 5 °C
8Air temperature
sensor#03 X = Ambient temperature
± 5 °C
9EGR solenoid valve
#24 X = 0
18
18
19
19
13-33

DPCF01 1.0
LUCAS DIESEL INJECTION
Fault finding - Checking conformity
13
Order of
operationsFunction to check Action Bargraph Display and notes
1 Change to status testG01* 7. dlE
Use fiche n° 60
status test side
2 No faultsEnsure this bargraph is not
flashing, otherwise enter
G02* and turn the fiche over.
Repair the faulty component
then erase the memory (G0**)
and return to status testing
(G01*)
3 Battery voltage#04 13 volts < X < 14.5 volts
Engine warm at idle speed after at least one operation of the engine cooling fan
assembly (air conditioning not selected).NOTES
20
13-34

DPCF01 1.0
LUCAS DIESEL INJECTION
Fault finding - Checking conformity
13
Engine warm at idle speed after at least one operation of the engine cooling fan
assembly (air conditioning not selected).NOTES
Order of
operationsFunction to check Action Bargraph Display and notes
4 Interpretation of
normally illuminated
bargraphs
-
Code present
Advance corrector fed
Illuminated if fast idle solenoid
valve is fed
Illuminated for 40 seconds at
idle speed after starting phase
Illuminated if command mode
G0** has been used since the
last dialogue took place
Illuminated for post heating
Illuminated if altimetric
corrector is fed
Illuminated if vehicle has a PAS
pump assembly
(AC version only)
Injection computer may give
load lever position to other
computers (not used)
Injection computer may give
engine speed information to
other computers (not used)1
2
2
3
4
5
6
6
11
11
13-35

DPCF01 1.0
LUCAS DIESEL INJECTION
Fault finding - Checking conformity
13
Engine warm at idle speed after at least one operation of the engine cooling fan
assembly (air conditioning not selected).NOTES
Order of
operationsFunction to check Action Bargraph Display and notes
5 EGR solenoid valve After starting
phase for
40 seconds
#24
After
40 seconds
#24EGR solenoid valve fed
X = 82
X = 0
6Computer
configuration
With AC
Without ACG50*3*
G50*8*
G50*4*
G50*9*With AC
With PAS with pump
Without AC
With conventional PAS
3
3
18
18
19
19
13-36

DPCF01 1.0
LUCAS DIESEL INJECTION
Fault finding - Customer complaints
13
Only consult these customer complaints after a complete check using the XR25.NOTES
No dialogue from the computer to the XR25.
Idle speed too high (when air conditioning not requested)
No fast idle when air conditioning requested
Starting fault (engine will not start or is difficult to start).
Warning light illuminates with no fault shown by the XR25.
Vehicle produces black smoke at altitude
Chart 1
Chart 2
Chart 3
Chart 4
Chart 5
Chart 6
13-37

DPCF01 1.0
LUCAS DIESEL INJECTION
Fault finding - Fault charts
13
AFTER REPAIR
Use bornier Elé. 1332 for any operations on the computer connector.NOTES
Chart 1NO DIALOGUE FROM THE COMPUTER TO THE XR25.
Ensure that the XR25 is not the cause of the fault by trying to communicate with the computer on ano-
ther vehicle. If the XR25 is not the cause of the fault and dialogue is not established with another compu-
ter on the same vehicle, a faulty computer may be causing interference on the K and L fault finding lines.
Disconnect connections successively to determine which computer is at fault.
Check the ISO selector is on position S8, that you are using the latest XR25 cassette and the correct access
code (D34).
Check the battery voltage and carry out any necessary operations to ensure the correct voltage (U battery
> 10.5 volts).
Carry out a road test then check using the XR25.
Deal with any illuminated fault bargraphs.
Check the 15 Amp fuses on the engine connection unit have not blown (positions 3 and 4).
Check the connection and condition of the connections on the computer connector and the connection
R67 engine / dashboard.
Check the computer is correctly fed:
- Earth on track 2 of the computer connector (check the condition and tightness of the engine earth
strap and the engine earth on the gearbox housing).
- + after ignition feed on track 1 of the computer connector.
Check the diagnostic socket is correctly fed:
- Earth on track 5.
- + before ignition feed on track 16.
Check and ensure the continuity and insulation of the lines in the connection diagnostic socket/
computer:
- Between track 10 of the computer connector and track 15 of the diagnostic socket.
- Between track 13 of the computer connector and track 7 of the diagnostic socket.
If fault finding is not established after these operations, replace the computer (consult the "Aid" section
for this operation).
13-38

DPCF01 1.0
LUCAS DIESEL INJECTION
Fault finding - Fault charts
13
Carry out a road test then check using the XR25.AFTER REPAIR
If the fault persists, check the fuel supply circuits (for the pump and the injectors).
If necessary, carry out a complete check of the engine (starter drive speed, pump timing, condition of
injectors, rocker arm clearances, compression, .....).NOTES
Chart 4STARTING FAULT (ENGINE WILL NOT START OR IS DIFFICULT TO
START) (warning light extinguished).
Only consult this customer complaint after a complete check using the XR25.
If no fault is shown by the XR25, ensure that the fault is not caused by a faulty immobiliser system.
Check the operation of the preheating system:
Start command mode G10*1* and check for a voltage at the plugs.
If the plugs are not fed, check the connection of the 3 track connector on the relay unit and the condition
of the 70 Amp fuse on the engine connection unit.
13-41