RENAULT SCENIC 2000 J64 / 1.G Technical Note 3426A Owner's Guide

Downloaded from www.Manualslib.com manuals search engine TOP AND FRONT OF ENGINE
Timing belt
11
11 - 5
Fit the reading head of Mot. 1505 and carry out the
measurement, then adjust the tension using the bolt
in contact with the belt until pretension value
T1 = 68 ± 3 Hertz is reached.
Tighten the tensioner.
Turn the crankshaft four times and reposition the
timing at top dead centre using the pin.
Remove pin Mot. 1054.
Apply a pretensioning torque using Mot. 1543 (fitted
with cover N˚ 3) by using a torque wrench adjusted to
a torque of 1.1 daN.m on the edge of the belt to be
measured.
Fit the reading head of Mot. 1505 and carry out the
measurement, then adjust the tension using the bolt
in contact with the belt until pretension value
T2 = 61 ± 5 Hertz is reached.
Tighten the tension wheel nut to a torque of 5 daN.m.
NOTE: it is vital that you tighten the tension wheel
nut to torque to avoid any slackening which may
cause damage to the engine.
Never refit a belt once removed, but replace it.
Replace the crankshaft pulley bolt and tighten it to a
torque of 2 daN.m plus an angle of 115˚ ± 15˚.
See section 07 "Accessories belt tension" for the
tension value for fitting the power assisted steering
belt.The belts on vehicles fitted with air conditioning are
tensioned by bringing the automatic tensioner plate to
a stop at bolt (B), without forcing it, using a 9.35 mm
square.
98837-1R1

Downloaded from www.Manualslib.com manuals search engine TOP AND FRONT OF ENGINE
Cylinder head gasket
11
11 - 6
Cylinder head gasket
SPECIAL TOOLING REQUIRED
Mot. 251 -01 Dial gauge support
Mot. 252 -01 Pressure plate to measure
piston protrusion
Mot. 1054 TDC setting pin
Mot. 1159 Tool for holding engine on
subframe
Mot. 1202 -01
Hose clip pliers
Mot. 1202-02
Mot. 1387 Tool for checking the automatic
tensioner centreline
Mot. 1448 Long nose pliers for hose clips
Mot. 1453 Engine support
Mot. 1505 Tool for measuring belt tension
Mot. 1453 Timing belt pretensioning
torque tool
ESSENTIAL SPECIAL TOOLING
Cylinder head testing equipment
14 torx socket
Angular tightening wrench
55 torx socket
REMOVAL
Put the vehicle on a 2 post lift.
Disconnect the battery.
Remove the engine undertray.
Drain the cooling circuit through the lower radiator
hose.
Remove:
– the timing belt (see method described in section 11,
"Timing belt").
– the two PAS pipe mountings on the right hand sub-
frame. TIGHTENING TORQUES (in daN.m and/or ˚)
Tension roller nut 5
Crankshaft pulley bolt 2 + 115˚ ± 15˚
Suspended mounting cover bolt 6.2
Suspended mounting limiter bolt 6.2
Torque reaction arm 6.2
Wheel bolts 9

Downloaded from www.Manualslib.com manuals search engine TOP AND FRONT OF ENGINE
Cylinder head gasket
11
11 - 7
Fit tool Mot. 1159 between the sub-frame and the
cylinder block.
NOTE: cut the base of Mot. 1159 by 30 mm.
Remove the engine mountings Mot. 1453.
99023R2
99024R2

Downloaded from www.Manualslib.com manuals search engine TOP AND FRONT OF ENGINE
Cylinder head gasket
11
11 - 8
Remove:
– the air filter assembly and the air inlet pipe,
– the air ducts (A) and (B),
– the injector connectors and the heater plugs,
– the connectors (1) and (2),
– the oil rebreather pipe (3),
16871R

Downloaded from www.Manualslib.com manuals search engine TOP AND FRONT OF ENGINE
Cylinder head gasket
11
11 - 9
– the brake servo vacuum pipe,
– the pipes on the cylinder head water outlet unit and
the sensor connections (1),
– the pipes (3),– the fuel pipes (4) (fit cleanliness plugs) and the wiring
mounting (5),
– the cylinder marking sensor (7),
16179R
16869R116870R5
16181R

Downloaded from www.Manualslib.com manuals search engine TOP AND FRONT OF ENGINE
Cylinder head gasket
11
11-10
– the low pressure pump connector,
– the bolts (1) and (2),
– the alternator mounting bolts and remove the
alternator, then remove the bolts (3).
Loosen the exhaust pipe clamp mounting.
Remove:
– the catalytic converter mountings on the pre-catalytic
converter,
– the pre-catalytic converter stay (1),
– the mounting (6),
– the oil supply pipe at (7) and remove towards the
bulkhead,
– the pre-catalytic converter mountings to the turbo,
– the catalytic converter removing the engine towards
the cooling system,
– the oil return pipe (8),– the bolt (9) and loosen the other mounting bolts on
the lower timing cover without removing them,
– cylinder head bolts.
Release the cylinder head by setting aside the lower
part of the camshaft housing, without causing the
cylinder head to turn, since this is centred by the two
dowels.
PRF1103
16155R
16156R2
12521-1R3

Downloaded from www.Manualslib.com manuals search engine TOP AND FRONT OF ENGINE
Cylinder head gasket
11
11-11
CLEANING
It is very important not to scratch the gasket faces
of any aluminium component.
Use the Décapjoint product to dissolve any part of the
gasket which remains attached.
W ear gloves whilst carrying out the following
operation.
– Apply the product to the parts to be cleaned; wait
about ten minutes, then remove it using a wooden
spatula.
W e must draw your attention to the care which
must be taken during this operation, to prevent
any foreign bodies from being introduced into the
oil ways (ducts located in the cylinder block and in
the cylinder head).
CHECKING THE GASKET FACE
Check for gasket face bow using a straight edge and a
set of shims.
Maximum deformation: 0.05 mm.
No regrinding of the cylinder head is permitted.
Check the cylinder head for cracks.Checking piston protrusion
Clean the piston heads in order to eliminate any traces
of deposits.
Turn the crankshaft in its operating direction, to bring
piston n ° 1 close to TDC.
Fit tool Mot. 252-01 on the piston.
Fit the tool Mot. 251-01 fitted with a gauge on the
pressure plate Mot. 252-01 (the dial gauge measuring
pin being in contact with the cylinder block) and look
for the TDC of the piston.
NOTE: All measurements are to be carried out in the
longitudinal axis of the engine, in order to eliminate
any errors due to tilting of the piston.
Max. piston protrusion: 0.72 ± 0.077 mm
12516S

Downloaded from www.Manualslib.com manuals search engine TOP AND FRONT OF ENGINE
Cylinder head gasket
11
11-12
REFITTING (special notes)
Fit the cylinder head gasket. This is centred by two
dowels.
Bring the pistons to mid-stroke position to prevent
them from coming into contact with the valves as the
cylinder head is tightened.
Centre the cylinder head on the dowels.
Lubricate the threads and under the heads of the
mounting bolts.
Tighten the cylinder head using an angular tightening
wrench (see section '07 "Tightening the cylinder
head").
Tightening procedure for the automatic tensioner
mounting
Offer up the three touching bolts then apply a torque of
2.5 daN.m respecting the order shown below.
Refitting is the reverse of removal.
Refit the timing belt, (see procedure described in
section 11 "Timing belt").
Fill and bleed the cooling circuit, (see section 19
"Filling and Bleeding").
To reprime the diesel circuit, consult section 13, "Fuel
filter".
PRF1102

Downloaded from www.Manualslib.com manuals search engine FUEL MIXTURE
Air intake
12
112
FUEL MIXTURE
Air intake
AIR INTAKE CIRCUIT DIAGRAM
1 Air-air exchanger
2 Air filter
3 Flow meter
4 Inlet manifold
5 Turbocharger
A Air inlet
12-1

Downloaded from www.Manualslib.com manuals search engine TURBOCHARGING
Pressure regulating valve
12
12-2
TURBOCHARGING
Pressure regulating valve
The LDA (A) of the pressure regulation valve is controlled by a solenoid valve (B) which is controlled by the injection
computer. This solenoid valve varies the underpressure as a function of the engine operating ranges, which allows
the turbocharging pressure to be regulated.
The pressure regulation valve is open in rest position. The engine operates as normally aspirated.
The solenoid valve, closed in rest position, is supplied after starting the engine, after a delay dependent on the coolant
temperature.
Delay (s)
Temperature (˚C)