bulb RENAULT SCENIC 2007 J84 / 2.G Anti Lock Braking System Bosch 8.0 ABS Workshop Manual

ANTI-LOCK BRAKING SYSTEM
Fault finding - Introduction
38C
38C - 2V2 MR-372-J84-38C000$066_eng.mif
138C
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Introduction
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding procedure applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this manual):
–Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
–Visu-Schéma (CD-ROM), paper version.
Type of diagnostic tools
–CLIP
Special tooling required
3. RECAP
Procedure
To perform fault finding on the vehicle's computers, switch on the ignition in fault finding mode.
Proceed as follows:
–vehicle's card in reader;
–press and hold the Start button (longer than 5 seconds) with start-up conditions not present,
–connect the diagnostic tool and perform the required operations.
To cut off + after ignition feed, proceed as follows:
–disconnect the diagnostic tool,
–press the Start button twice briefly (less than 3 seconds),
–Ensure that the + after ignition feed has been cut off by checking that the computer indicator lights on the instrument
panel have gone out. Vehicle(s): Mégane II, Scénic II
Function concerned: ABSName of computer: BOSCH ABS 8.0
Vdiag No: 0C, 0D, 0E, 0F
Special tooling required
Multimeter
Elé. 1681Universal bornier
Note:
The left and right-hand discharge bulb computers are supplied when the dipped headlights are lit. Therefore fault
finding can only be carried out on them after the ignition has been switched on in fault finding mode (forced + after
ignition feed) and the dipped headlights have been switched on.
ABS8.0_V0C_PRELI /ABS8.0_V0D_PRELI /ABS8.0_V0E_PRELI/ABS8.0_V0F_PRELI ABS 8.0X84 4.0
MR-372-J84-38C000$066_eng.mif

ANTI-LOCK BRAKING SYSTEM
Fault finding - System operation
38C
38C - 7V2 MR-372-J84-38C000$132_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - System operation
The main functions of ABS on this vehicle are the electronic balancing of front and rear braking by controlling rear
wheel slip and preventing the brakes from locking by controlling the slipping of all four wheels.
The system also supplies the other computers with information on the vehicle speed via a wire connection for the
discharge bulbs, the radio and the electric sunroof, and via the multiplex network for the other computers. The ABS
computer supplies the multiplex network with the odometry for the instrument panel and navigation system. If heavy
braking produces very rapid deceleration, the ABS computer sends out a request to the UCH via the multiplex network
to ask it to switch on the hazard warning lights (depending on the law in the relevant country).
Fault finding warning light illumination strategy for Mégane II ph1 and Scénic II ph 1
Instrument panel warning lightInstrument panel message
Meaning
MEGANE II SCENIC II
Brake faultsABS SERVICE STOPNo message"Brake
fault"Electronic brake
distribution and ABS
functions inoperative.
ABS SERVICENo messageCheck the
ABSABS function
inoperative.
Brake faults
flashing at
2 HzABS flashing
at 2 HzNo messageNo
messageABS computer is in
fault finding mode.
ABS flashing
at 8 HzNo messageNo
messageTachometric index not
programmed.
NOTE:
The STOP warning light is always accompanied by a single audible warning (1 beep).
ABS 8.0X84 4.0
MR-372-J84-38C000$132_eng.mif

ANTI-LOCK BRAKING SYSTEM
Fault finding - Configurations and programming38C
38C - 10V2 MR-372-J84-38C000$264_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Configurations and programming
Settings
VP001: Write VIN.
This command allows the vehicle identification number to be entered into the computer. Use this
command each time the computer is replaced. The VIN number (VF...) can be found on the
manufacturer's plate on the front right-hand door pillar and on the body panel under the left-hand side
of the windscreen.
VP004: Vehicle parameters.
This command is used to configure the engine type + braking definition + body type.
Select command VP004 on the diagnostic tool (it is imperative to check that the variants selected
correspond to the vehicle type).
VP006: Write date of the last After-Sales service.
Whenever the ABS system is worked on in the shop, the date must be entered.
Select command VP006 on the diagnostic tool.
Enter the operation date with the tool keyboard.
VP007: Tachometric index.
This command is used to program the computer memory with the index required to calculate vehicle
speed from the speed at which the wheels turn.
The BOSCH ABS 8.0 computer supplies the vehicle speed signal to all vehicle systems that use this
information (instrument panel, engine management, etc.). This vehicle speed signal replaces the one
supplied by the speed sensor located on the gearbox. The ABS computer calculates the vehicle speed
from the speed of the wheels and the circumference of the tyres fitted on the vehicle.
Note:
The vehicle speed is sent by wire (track 23) to the xenon bulb computer, radio and electric sunroof, and
via the multiplex network to the other computers.
The tyre circumference must be programmed into the memory of a new computer. This consists
of entering a number X using the VP007 "Tachometric index" command on the diagnostic tool.
Once the number has been entered using the VP007 command, delete the fault in the computer memory
and then switch off the ignition. Use the parameter PR030 to check that the index entered has been
stored correctly.
VP032: Vehicle speed at initialisation.
Vehicle speed transmitted via the multiplex network when the computer is initialised.
Select "Type 1" or "Type 2" according to the information supplied by the tool.
ABS 8.0X84 4.0
MR-372-J84-38C000$264_eng.mif

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 22V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
DF020
PRESENT
TACHOMETRIC INDEX PROGRAMMING
NOTESSpecial notes:
ABS warning light flashing at 8 Hz outside fault finding conditions.
The BOSCH ABS 8.0 computer supplies the vehicle speed signal to all vehicle systems that use this information
(instrument panel, engine management, etc.).
This vehicle speed signal replaces the one supplied by the speed sensor located on the gearbox. The ABS
computer calculates the vehicle speed from the speed of the wheels and the circumference of the tyres fitted on
the vehicle.
Note:
The vehicle speed is sent by wire (track 23) to the xenon bulb computer, radio and electric sunroof, and via the
multiplex network to the other computers.
The tyre circumference must be programmed into the memory of a new computer. This consists of
entering a number X using the VP007 "Tachometric index" command on the diagnostic tool.
Once the index has been entered using the VP007 command, clear the computer fault memory and then switch
off the ignition.
Use the parameter PR030 to check that the index entered has been stored correctly.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF020 /ABS8.0_V0D_DF020/ABS8.0_V0E_DF020/ABS8.0_V0F_DF020 ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of faults
38C
38C - 41V2 MR-372-J84-38C000$396_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
DF188
PRESENT
OR
STOREDBRAKE LIGHT SWITCH CIRCUIT
NOTESSpecial notes:
This fault does not cause illumination of any warning lights, nor does it generate any
fault message.
Conditions for applying the fault finding procedure to stored faults:
Clear the stored fault, carry out a road test at a speed of > 37 mph (60 km/h) and test
the brakes using ABS.
Check the conformity of the brake light bulbs.
Using the diagnostic tool, check on the statuses screen that ET017 Brake pedal displays the pressed and released
positions of the brake pedal correctly.
If the correct pedal position is not displayed, use the interpretation of ET017.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS8.0_V0C_DF188 /ABS8.0_V0D_DF188/ABS8.0_V0E_DF188/ABS8.0_V0F_DF188 ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Interpretation of statuses
38C
38C - 46V2 MR-372-J84-38C000$660_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0F
ET017
CONTINUED
Status is "pressed" with brake pedal released.
–Check the condition and fitting of the brake light switch, the brake lights fuse and the conformity of the bulbs.
–Remove the brake light switch and check that it is operating correctly:
Continuity between tracks Insulation between tracks
Switch pressed
(Brake pedal released)3 and 4 1 and 2
Switch released
(Brake pedal depressed)1 and 2 3 and 4
–Replace the switch if necessary.
–Check and ensure insulation against 12 V on the connection between track 1 of the brake switch connector and
track 20 of the computer connector.
AFTER REPAIRClear the computer fault memory.
Carry out a road test followed by another check with the diagnostic tool.
ABS 8.0X84 4.0

ANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with commands
38C
38C - 48V2 MR-372-J84-38C000$792_eng.mif
BOSCH ABS 8.0
Vdiag No.: 0C, 0D, 0E, 0FANTI-LOCK BRAKING SYSTEM
Fault finding - Dealing with commands
CLEARING
RZ001:Fault memory.
This command is used for clearing the computer's stored faults.
ACTIVATION
AC003:
AC004:
AC005:
AC006:Front left-hand wheel solenoid valves.
Front right-hand wheel solenoid valves.
Rear left-hand wheel solenoid valves.
Rear right-hand wheel solenoid valves.
These commands permit a check on the hydraulics of each wheel.
Position the vehicle on a 2-post lift so that the free rotation of the wheels can be checked.
Keep the brake pedal depressed enough to prevent the wheel being tested from being turned by hand (do not brake
so hard that the anti-lock function operates).
Select and confirm the command for the wheel in question (e.g. Left-hand front wheel solenoid valve, etc.).
Turn the wheel concerned by hand: 5 braking/releasing cycles should be detected.
AC013:Wheel speed sensor supply test.
This command is used to check that voltage pulses of approximately 12 V are detected on the faulty
sensor by a multimeter at the terminals of the sensor connector on the computer side.
You must use command AC013 once only.
AC016:Pump motor test.
This command is used to test the pump motor control circuit.
Select command AC016 Pump Motor Test.
The motor must run for 5 seconds.
AC195:Vehicle speed signal.
This command serves to generate a speed other than 0 mph at the computer's vehicle speed wire output
(Track 23) for users of that signal (xenon bulbs, radio, sunroof).
Note:
This command has no visible effect on the dashboard speedometer needle.
–Xenon headlights: Switch on the dipped headlights and run command AC195. Check for slight
variation in the height of the headlight beam while the command is running (the height of the beam is
adjusted to improve visibility according to vehicle speed).
–Radio: Turn on the radio and make sure that the Adjust volume as a function of speed function is
active. Run command AC195. Check that the volume of the sound increases and then decreases
while the command is running.
–Sunroof: This command has no visible effect on the sunroof. This command changes the activation
threshold of the anti-pinch system (the pressure exerted by the sunroof varies with vehicle speed due
to aerodynamic factors).
AC196:Request to switch on hazard warning lights.
This command sends the UCH a request to switch on the hazard warning lights to test their operation
during emergency braking (depending on UCH configuration).
ABS 8.0X84 4.0
MR-372-J84-38C000$792_eng.mif