sensor RENAULT SCENIC 2008 J84 / 2.G Parking Distance Control User Guide

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 17V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF004
PRESENT
OR
STOREDRIGHT-HAND OUTER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking distance
control function is ACTIVE (ready): the parking distance control warning light is not lit,
see the interpretation of status ET003 Parking distance control function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
When dealing with a combination of faults on the sensors:
Check the connection and the status of the intermediate connectors (the sensors up to the computer). Repair if
necessary.
Check for + 12 V, after ignition, between tracks 1 and 3 of all the sensors.
Computer with 1 connector:
Check the insulation, continuity and the absence of interference resistance of the supply for each sensor
(between tracks 1 and 3) and for the computer (between tracks 9 and 10).
Computer with 2 connectors:
Check the insulation, continuity and absence of interference resistance of the supply between tracks 1 and 3
for each sensor and between tracks 8 and 11 of the computer 12-track connector.
In the case where only one sensor is faulty:
Swap the defective sensor with a non-defective sensor.
Check for faults:
If the sensor is no longer faulty, replace the defective sensor.
If the fault is still present, with the ignition off, disconnect the parking distance control computer connector to
check the insulation, continuity and the absence of interference resistance on the following connections:
1 connector:
Parking distance control computer Right-hand outer sensor
Track 9 Track 1
Track 16 Track 2
Track 10 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF004/AAP_V08_DF004

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 18V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
DF004
(CONTINUED)
2 connectors:
12-track parking distance control computer
connectorRight-hand outer sensor
Track 11 Track 1
Track 4 Track 2
Track 8 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.

PARKING DISTANCE CONTROL
87F
87F - 19V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF005
PRESENT
OR
STOREDRIGHT-HAND INNER SENSOR
CC.1 : Short circuit to + 12 V
CO.0 : Open circuit or short circuit to earth
1.DEF : Internal electronic fault
NOTESConditions for applying the fault finding procedure to stored faults:
The fault is declared present following selection of reverse gear if the parking distance
control function is ACTIVE (READY): the parking distance control warning light is not
lit, see the interpretation of status ET003 Parking distance control function.
Special notes:
This fault is indicated by the buzzer (a 5 second warning sound) and the system shuts
down.
If a combination of faults are present on the sensors:
Check the connection and condition of the intermediate connectors (the sensors up to the computer). Repair if
necessary.
Check for + 12 V, after ignition, between tracks 1 and 3 of all the sensors.
Computer with 1 connector:
Check the insulation, continuity and the absence of interference resistance of the supply for each sensor
(between tracks 1 and 3) and for the computer (between tracks 9 and 10).
Computer with 2 connectors:
Check the insulation, continuity and absence of interference resistance of the supply between tracks 1 and 3
for each sensor and between tracks 8 and 11 of the computer 12-track connector.
In the case where only one sensor is faulty:
Swap the defective sensor with a non-defective sensor.
Check for faults:
If the sensor is no longer faulty, replace the defective sensor.
If the fault is still present, with the ignition off, disconnect the parking distance control computer connector to
check the insulation, continuity and the absence of interference resistance on the following connections:
1 connector:
Parking distance control computer Right-hand inner sensor
Track 9 Track 1
Track 13 Track 2
Track 10 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF005/AAP_V08_DF005

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 20V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
DF005
(CONTINUED)
2 connectors:
12-track parking distance control computer
connectorRight-hand inner sensor
Track 11 Track 1
Track 2 Track 2
Track 8 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.

PARKING DISTANCE CONTROL
87F
87F - 23V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF007
PRESENT
OR
STOREDSENSOR SUPPLY VOLTAGE
CO.0 : Open circuit
NOTESConditions for applying the fault finding procedure to stored faults:
The fault reappears present or stored after its has been cleared, the ignition is switched
on and off again and reverse gear is selected.
Special notes:
The sensors are directly supplied with + 12 V by the computer.
Computer with 1 connector:
With the parking distance control computer 16-track connector connected and with the ignition on, measure the
sensor power supply coming from the computer. The voltage should be equal to the battery voltage (± 0.5 V)
when measured across track 9 (+ 12 V) and track 10 (earth).
If there is not a + 12 V power supply between the tracks specified above, remove the rear bumper to access the
sensors.
Computer with 2 connectors:
With the parking distance control computer 12-track connector connected and with the ignition on, measure the
sensor power supply from the computer outlet. The voltage should be equal to the battery voltage (± 0.5 V) when
measured across track 11 (+ 12 V) and track 8 (earth).
If there is not a + 12 V power supply between the tracks specified above, remove the rear bumper to access the
sensors.
Switch off the ignition, and disconnect the parking distance control computer connector to check the insulation
and continuity and the absence of interference resistance on the following connections:
1 connector:
Parking proximity sensor computer connector Sensors
Track 9 Track 1 of the four sensors
Track 10 Track 3 of the four sensors
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF007/AAP_V08_DF007

PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
87F
87F - 24V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Interpretation of faults
DF007
(CONTINUED)
2 connectors:
12-track parking distance control computer
connectorRight-hand inner sensor
Track 11 Track 1
Track 8 Track 3
Repair if necessary (see Technical Note 6015A, Repairing electrical wiring, Wiring: Precautions for repair),
repair the wiring, otherwise replace the wiring.
If the sensor power supply is correct (no short circuit), reconnect the computer connector and four sensor
connectors.
Turn on the ignition and disconnect the sensors, one at a time, to see if any of the sensors causes the power supply
to drop. Replace the defective sensor.
If the fault is still present, contact the Techline.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.

PARKING DISTANCE CONTROL
87F
87F - 27V4 MR-372-J84-87F000$462_eng.mif
Vdiag No: 04-08
Fault finding - Interpretation of faults
DF012
PRESENT
OR
STOREDPARKING DISTANCE CONTROL SWITCH INDICATOR LIGHT
CC.0 : short circuit to earth or open circuit
CO.1 : open circuit or short circuit to + 12 volts
NOTESConditions for applying the fault finding procedure to stored faults:
A fault is declared present after reverse gear is engaged and the parking distance
control deactivation switch is pressed.
Remove the parking distance control switch and check the connections and condition of its connector.
Repair if necessary.
Check for an earth on track B3 of the parking distance control switch connector.
Repair if necessary.
Switch off the ignition, and disconnect the parking distance control computer 16-track connector to check the
insulation and continuity and the absence of interference resistance on the following connection:
Laguna II ph2, Espace IV ph2, Vel-Satis ph2, Mégane II, Scénic II, Laguna II ph1 (1 connector),
Espace IV ph1 (1 connector), Vel-Satis ph1 (1 connector), Laguna II ph1 (2 connectors),
Vel- Satis ph1 (2 connectors), Clio III, Modus ph2:
Parking distance control switch connector Parking proximity sensor computer connector
Track B2 Track 5
Repair if necessary.
Espace IV ph1 (2 connectors):
Parking distance control switch connector16-track parking distance control computer
connector
Track B2 Track 13
Repair if necessary.
If the fault is still present, replace the parking distance control switch.
AFTER REPAIRClear the stored faults.
Follow the instructions to confirm repair.
Deal with any faults.
AAP_V04_DF012/AAP_V08_DF012

PARKING DISTANCE CONTROL
Fault finding - Conformity check
87F
87F - 28V4 MR-372-J84-87F000$528_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Conformity check
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
Conditions for applying the fault finding procedure: ignition on.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Parking
distance control
system statusET003:Parking
distance
control
functionREADY (system
operating and ready to
detect)
For further information or,
if there is a fault, consult
the interpretation of status
ET003. DETECTING (if the
system is detecting)
SUSPENDED (if the
system is temporarily
switched off)
OFF (if the system is
completely switched off)
2Parking
distance control
deactivation
switch.ET004:Parking
distance
control switchPRESS DETECTED
when the switch is
pressed, RELEASED
when released.In the event of a fault,
consult the interpretation
of status ET004.
3FeedsPR006:Sensor feed
voltage10.5 V < X < 14.4 VIn the event of a fault,
apply the fault finding
procedure for DF007
Sensor supply voltage.
PR020:Computer
feed voltage10.5 V < X < 14.4 VIf there is a fault with this
parameter, check the
insulation, continuity
and the absence of
interference resistance
on the computer power
feed and earth (see wiring
diagram). If the fault is still
present, carry out fault
finding on the charging
circuit.
4Reverse gear
selectionET001:Reverse gear
engagedYES or NOIf there is a fault, refer to
the interpretation of status
ET001.
AAP_V04_CCONF/AAP_V08_CCONF
MR-372-J84-87F000$528_eng.mif

PARKING DISTANCE CONTROL
Fault finding - Conformity check
87F
87F - 29V4 MR-372-J84-87F000$528_eng.mif
Vdiag No: 04-08
NOTESOnly perform this conformity check after a thorough check with the diagnostic tool.
Conditions for applying the fault finding procedure: ignition on.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
5Buzzer controlET002:Buzzer controlACTIVE when the buzzer
sounds.
INACTIVE if not.In the event of a fault,
consult the interpretation
of status ET002.
6Proximity
sensorsPR001:Left-hand
outer sensor
distance20 cm < X < 150 cm
depending on the distance
from the obstacle (“out of
range” value: 255 cm).In the event of a fault, refer
to the interpretation of the
parameter PR001.
PR002:Left-hand
inner sensor
distance20 cm < X < 150 cm
depending on the distance
from the obstacle (“out of
range” value: 255 cm).If there is a fault, refer to
the interpretation of
parameter PR002.
PR003:Right-hand
outer sensor
distance20 cm < X < 150 cm
depending on the distance
from the obstacle (“out of
range” value: 255 cm).In the event of a fault,
consult the interpretation
of parameter PR003.
PR004:Right-hand
inner sensor
distance20 cm < X < 150 cm
depending on the distance
from the obstacle (“out of
range” value: 255 cm).If there is a fault, refer to
the interpretation of
parameter PR004.
PR005:Shortest
distance
calculated20 cm < X < 150 cm
depending on the distance
from the obstacle (“out of
range” value: 255 cm).If there is a fault, refer to
the interpretation of
parameter PR005.
7Vdiag 08 only:
Caravan
attachment
detection zonePR026:Distance from
the caravan
attachmentBy default: 35 cm
Beyond 40 cm, the
function is less effective,
(setting the detection area
of the rear centre sensors
so that the presence of a
caravan towbar is not
detected)If the caravan attachment
is detected, increase the
non-detection value using
parameter VP003.
VP003:Distance from
the caravan
attachmentEnables the non-detection
area for the caravan
attachment to be
modified.

PARKING DISTANCE CONTROL
87F
87F - 39V4 MR-372-J84-87F000$726_eng.mif
Vdiag No: 04-08PARKING DISTANCE CONTROL
Fault finding - Parameter summary table
Tool parameter Diagnostic tool title
PR001Left-hand outer sensor distance
PR002Left-hand inner sensor distance
PR003Right-hand outer sensor distance
PR004Right-hand inner sensor distance
PR005Shortest distance calculated
PR006Sensor feed voltage
PR020Computer feed voltage
PR026Distance from caravan attachment (Vdiag 08 only)
MR-372-J84-87F000$726_eng.mif