RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Workshop Manual

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -131
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -131V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre approval (continued 1)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre approval PR004:Front right-hand
wheel pressure0 bar < X < 3.55 barIf X = 0 bar, consult the fault
finding procedure for parameter
PR004.
Check that the recommended
pressure (PR009 to PR012)
corresponds correctly to the
vehicle.
PR020:Front right-hand tyre
temperature- 40ºC normal that the temperature is
50˚C and the pressure is 0 bar.
Perform a road test so that the
sensor emits the actual
temperature and pressure.
ET034:Rear right-hand
wheel valve signalOK
ABSENT
OVER-INFLATED
FLAT
UNDER-INFLATEDCheck that the tyre pressure is
at the recommended pressure
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
If status ET034 is not OK,
consult the fault finding
procedure for status ET034.
PR005:Rear right-hand
wheel pressure0 bar < X < 3.55 barIf X = 0 bar, consult the fault
finding procedure for parameter
PR005.
Check that the recommended
pressure (PR009 to PR012)
corresponds correctly to the
vehicle.
PR021:Rear right-hand tyre
temperature- 40ºC normal that the temperature is
50˚C and the pressure is 0 bar.
Perform a road test so that the
sensor emits the actual
temperature and pressure.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -132
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -132V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre approval (continued 2)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre approval ET035:Rear left-hand
wheel valve signalOK
ABSENT
OVER-INFLATED
FLAT
UNDER-INFLATEDCheck that the tyre pressure is
at the recommended pressure
(see MR 364 (Mégane II) or
MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
If status ET035 is not OK,
consult the fault finding
procedure for status ET035.
PR006:Rear left-hand
wheel pressure0 bar < X < 3.55 barIf X = 0 bar, consult the fault
finding procedure for parameter
PR006.
Check that the recommended
pressure (PR009 to PR012)
corresponds correctly to the
vehicle.
PR022:Rear left-hand tyre
temperature- 40ºC normal that the temperature is
50˚C and the pressure is 0 bar.
Perform a road test so that the
sensor emits the actual
temperature and pressure.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -133
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -133V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre management
fr*: front,
rr*: rear.
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre
management PR009:Fr* wheel low speed
recommended
pressure.
In barCheck that the values entered
are actually the recommended
ones (see MR 364 (Mégane II)
or MR 370 (Scénic II),
Mechanical, 35A, Tyre
pressure: Identification).
Otherwise, enter the
recommended pressures using
command VP005 Write
recommended pressures. PR010:Rr* wheel low speed
recommended
pressure.
PR012:Fr* wheel high speed
recommended
pressure.
PR011:Rr* wheel high
speed
recommended
pressure.
PR014:Left/right pressure
difference threshold0.5 bar
None. PR015:Low under-inflation
threshold- 0.4 bar
PR059:Puncture report
threshold- 0.6 bar
PR017:Cold over-inflation
threshold0.7 bar
PR018:Warm over-inflation
threshold0.8 bar

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -134
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -134V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
FUNCTION: TYRES
Sub-function: Tyre display
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Tyre displayET039:STOP warning light
on request ACTIVE
INACTIVEACTIVE, if a puncture is
detected.
There is a buzzer
activation request for all
severity level 1
warnings (puncture).
The buzzer emits a
single beep when a fault
occurs.
ET016:Buzzer activation
requestINACTIVE
STATUS 1
STATUS 2
INCONSISTENCY STATUS 1: request for
buzzer activation when
a puncture is detected.
STATUS 2: request for
buzzer activation to
warn the driver that the
vehicle speed is too
high when the vehicle
has one or more
punctured tyres. This
information is only valid
on vehicles fitted with
PAX System tyres.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -135
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -135V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
LIGHTING FUNCTION
Sub-function: Lighting command
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Lighting
controlET081:Lighting switch
positionOFF
SIDE
DIPPED
MAIN BEAM HEADLIGHTS
HAZARD LIGHTS In the event of a fault,
refer to the
interpretation of status
ET081.
ET115:Request to switch
on lights by light
sensor PRESENT
ABSENTIn the event of a fault,
consult the
interpretation of status
ET115.
ET169:EngineSTOPPEDIn the event of a fault,
refer to the
interpretation of
status ET169.
ET113:Automatic lighting
button DEPRESSED
RELEASED In the event of a fault,
consult the
interpretation of
status ET113.
ET111:Front fog lights
requestPRESENT
ABSENT In the event of a fault,
consult the
interpretation of
status ET111.
ET082:Rear fog lights
requestPRESENT
ABSENT In the event of a fault,
consult the
interpretation of
status ET082.
ET085:Hazard warning
lights buttonDEPRESSED
RELEASED In the event of a fault,
refer to the
interpretation of
status ET085.
ET083:Left-hand indicator
requestPRESENT
ABSENT In the event of a fault,
refer to the
interpretation of
status ET083.
ET084:Right-hand indicator
requestPRESENT
ABSENT In the event of a fault,
refer to the
interpretation of
status ET084.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -136
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -136V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
WIPING FUNCTION
Sub function: Wiper control
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Wiper controlET077:Wiper stalk positionOFF
INTERMITTENT
LOW SPEED HIGH SPEEDIn the event of a fault,
refer to the
interpretation of status
ET077.
ET096:Wiper stalk
intermittent speed
ring position1
2
3
4In the event of a fault,
consult the
interpretation of
status ET096.
ET118:Rain sensor
sensitivity ring
position
ET114:Wiper request by rain
sensorPRESENT
ABSENTIn the event of a fault,
consult the
interpretation of
status ET114.
ET078:Windscreen washer
requestPRESENT
ABSENTIn the event of a fault,
refer to the
interpretation of status
ET078.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -137
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -137V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
WIPING FUNCTION
Sub-function: Wiper control (continued)
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-
functionParameter or
Status
checked Action Display and Notes Fault finding
Wiper controlET080:Rear screen wiper
requestPRESENT
ABSENTIn the event of a fault,
consult the
interpretation of
status ET080.
ET097:Rear screen wiper
park positionPRESENT
ABSENTIn the event of a fault,
consult the status
interpretation ET097.
ET079:Rear screen washer
requestPRESENT
ABSENTIn the event of a fault,
refer to the
interpretation of status
ET079.
ET109:Reverse gear
engagedYES
NO In the event of a fault,
check the reverse gear
switch and its
connections.
ET108:Automatic gearbox
lever positionNOT IN NEUTRAL
P
NEUTRAL
REARIn the event of a fault,
consult the
interpretation of
status ET108.

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -138
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Conformity check
87B
87B -138V9 MR-372-J84-87B000$387.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
LIGHTING FUNCTION
Sub-function: Lighting power
NOTESOnly carry out this conformity check after a complete check with the diagnostic tool
(fault reading and configuration checks).
Application condition: engine stopped, + after ignition feed present.
Sub-functionParameter or
Status
checked Action Display and Notes Fault finding
Lighting powerET112:Interior lighting
controlACTIVE
INACTIVENone

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -139
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -139V9 MR-372-J84-87B000$430.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
*RCH = Passenger Compartment Heating ResistorTool status Diagnostic tool title Vdiag
ET008UCH blankV44, V48, V4C,
V4D, V4F, V50
ET010Card frequency (in MHz)V44, V48, V4C,
V4D
ET014Control power level
V44, V48, V4C,
V4D, V4F, V50 ET015Passenger compartment fan
ET016Buzzer activation request
ET017Number of RCH* required
ET018Number of RCH* authorised by alternator
ET019Number of RCH* authorised by injection computer
ET020Number RCH* activated.
ET021RCH* 1 relay control
ET022RCH* 2 relay control
ET023RCH* 3 relay control
ET025Retractable roof V48, V4C, V4D,
V4F, V50
ET026Heated rear screen switch
V44, V48, V4C,
V4D, V4F, V50 ET028Heated rear screen button
ET029Air conditioning button
ET030Air conditioning request 2
ET031Fast idle speed request for RCH*
ET032Front left-hand wheel valve signal
ET033Front right-hand wheel valve signal
ET034Rear right-hand wheel valve signal
ET035Rear left-hand wheel valve signal
ET038Service warning light on request
ET039STOP warning light on request
ET040Tyre pressure monitoring system
MR-372-J84-87B000$430.mif

PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -140
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Status summary table
87B
87B -140V9 MR-372-J84-87B000$430.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
*RAID: Renault Anti-Intruder Device
*CPE: Electric central door locking
*Lckg: Locking Tool status Diagnostic tool title Vdiag
ET041Opening rear screenV48, V4C, V4D,
V4F, V50
ET042Passenger door V44, V48, V4C,
V4D, V4F, V50
ET043RAID* function authorisation by CPE*
V44, V48, V4C,
V4D, V4F, V50 ET044CPE* button
ET045RF signal received
ET046Engine immobiliser
ET047Brake pedal position
ET048Clutch pedal position
ET050Tailgate/Boot
ET051Rear left-hand door
ET052Rear right-hand door
ET053Driver's door
ET054Optical sensors supplied
ET055Front driver side optical sensor
ET056Rear driver side optical sensor
ET057Passenger side front/rear optical sensor
ET058Lckg* button on driver's side handles
ET059Lckg* buttons on passenger's side handles
ET060Tailgate locking button
ET061Open tailgate request
ET062Open rear screen requestV48, V4C, V4D,
V4F, V50