steering RENAULT SCENIC 2008 J84 / 2.G Passenger Comparment Connection Unit Service Manual
[x] Cancel search | Manufacturer: RENAULT, Model Year: 2008, Model line: SCENIC, Model: RENAULT SCENIC 2008 J84 / 2.GPages: 391
Page 218 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 218
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 218V9 MR-372-J84-87B000$559.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET096
CONTINUED 2
ET096 is Level 1 but with speed level 3 requested.
Check the operation of the following statuses:
ET083 Left-hand direction indicator request: Set the lighting stalk to the left-hand direction indicator.
ET077 Wiper stalk position: Set the windscreen wiper stalk to the low speed position.
Check in the following table and apply the fault finding procedure according to the result obtained.
Result 1 Result 2 Result 3 Result 4
ET083 Left-hand direction
indicator requestPresent Absent Absent Present
ET077 Wiper stalk position at
High speedLow speed High speed Low speed High speed
Change the
steering
column control
Check the continuity and insulation of the following connection:
●Connection code 141H between components 645 and 1519.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Check the continuity and insulation of the following connection:
●Connection code 141L between components 645 and 1519.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Check the continuity and insulation of the following connections:
●Connection code 141N.
●Connection code 141L between components 645 and 1519.
If the connection or connections are faulty and there is a repair procedure (see
Technical Note 6015A, Electrical wiring repair, Wiring: Precautions for repair),
repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline.
Result 1
Result 2
Result 3
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
Page 219 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 219
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 219V9 MR-372-J84-87B000$559.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET096
CONTINUED 3
NOTESNo faults should be present or stored.
ET096 is Level 1 but with speed level 4 requested.
Check the operation of the following statuses:
ET077 Wiper stalk position: set the windscreen wiper stalk to high speed.
ET081 Lighting stalk position: set the lighting stalk to main beam headlights position.
Check in the following table and apply the fault finding procedure according to the result obtained.
Result 1 Result 2 Result 3 Result 4
ET077 Wiper stalk position at
high speedHigh speed Low speed Low speed High speed
ET081 Lighting stalk in the main
beam headlights position Dipped
headlightsMain beamDipped
headlightsMain beam
Change the
steering
column control
Check the continuity and insulation of the following connection:
●Connection code 141H between components 645 and 1519.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Result 1
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
Page 222 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 222
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 222V9 MR-372-J84-87B000$559.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET098
TRIP COMPUTER BUTTON
NOTESNo faults should be present or stored.
This status must change to Pressed when the button is pressed.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
ET098 is Released with the button pressed.
Check the operation of the following statuses:
ET082 Rear fog light request: Set the lighting stalk to the rear fog light position.
ET081 Lighting stalk position: Set the lighting stalk to dipped headlights position.
Check in the following table and apply the fault finding procedure according to the result obtained.
Result 1 Result 2 Result 3 Result 4
ET082 Rear fog lights requestPresent Absent Absent Present
ET081 Dipped headlights wiper
stalk positionOffDipped
headlightsOffDipped
headlights
Change the
steering
column control
Check the continuity and insulation of the following connection:
●Connection code 141K between components 645 and 1519.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
If the fault is still present, contact the Techline.
Result 1
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET098/UCH_V48_ET098/ UCH_V4C_ET098/
UCH_V4D_ET098 /UCH_V4F_ET098/UCH_V50_ET098
Page 227 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 227
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 227V9 MR-372-J84-87B000$559.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET111
FRONT FOG LIGHTS REQUEST
NOTESNo faults should be present or stored.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
ET111 is Absent with the stalk in front fog lights position.
Check the operation of the following statuses:
ET083 Left-hand direction indicator request: Set the control stalk to the left-hand indicator.
ET080 Rear screen wiper request: Set control stalk to rear screen wiper request.
Check in the following table and apply the fault finding procedure according to the result obtained.
Result 1 Result 2 Result 3 Result 4
ET083 Left-hand direction
indicator requestPresent Absent Absent Present
ET080 Rear screen wiper requestAbsent Present Absent Present
Change the
steering
column control
Check the continuity and insulation of the following connection:
●Connection code 141K between components 645 and 1519.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Result 1
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET111/UCH_V48_ET111/UCH_V4C_ET111/
UCH_V4D_ET111/UCH_V4F_ET111/UCH_V50_ET111
Page 230 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 230
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 230V9 MR-372-J84-87B000$559.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET113
AUTOMATIC LIGHTING BUTTON
NOTESNo faults should be present or stored.
Use Wiring Diagrams Technical Note for MEGANE II or SCENIC II.
ET113 Released with one press on the button.
Check the operation of the following statuses:
ET083 Left-hand direction indicator request: Set the control stalk to the left-hand indicator.
ET096 Windscreen wiper stalk intermittent speed ring position: Set the stalk to the rear fog light position.
Check in the following table and apply the fault finding procedure according to the result obtained.
Result 1 Result 2 Result 3 Result 4
ET083 Left-hand direction
indicator requestPresent Absent Absent Present
ET096 Windscreen wiper
intermittent ring position4141
Change the
steering
column control
Check the continuity and insulation of the following connection:
●Connection code 141L between components 645 and 1519.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A,
Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
Result 1
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET113/UCH_V48_ET113/UCH_V4C_ET113/
UCH_V4D_ET113/UCH_V4F_ET113/UCH_V50_ET113
Page 237 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 237
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Interpretation of statuses87B
87B - 237V9 MR-372-J84-87B000$602.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ET229
INJECTION IMMOBILISER CODE
NOTESNo faults should be present or stored.
Apply the checks only if the status remains INCORRECT after the ignition is switched
off and back on.
INCORRECT
Try to start the vehicle, ensuring that the steering column lock unlocks properly and that
the + after ignition feed has been established on the vehicle using ET014 Control
power level.
First check the operation of status ET046 Engine immobiliser.
Carry out a multiplex network test.
Run fault finding on the injection system.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out another fault finding check on the system.
Clear the stored faults.
Deal with any other faults.
UCH_V44_ET229/UCH_V48_ET229/ UCH_V4C_ET229/
UCH_V4D_ET229 /UCH_V4F_ET229/UCH_V50_ET229
Page 297 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Customer complaints
87B
87B -297
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Customer complaints
87B
87B -297V9 MR-372-J84-87B000$860.mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ANTITHEFT AND STARTING RECORDED FAULTS
NO + ACCESSORIES FEED ALP39
FORCED AFTER-IGNITION FEED FAILS ALP40
THE VEHICLE DOES NOT START AND THE AFTER IGNITION FEED
FAILS, CARD IN THE CARD READERALP41
THE VEHICLE DOES NOT START, THE AFTER IGNITION FEED
FAILS IN HANDS-FREE MODE BUT WORKS WITH THE CARD IN THE
CARD READERALP42
THE VEHICLE FAILS TO START AND GOES INTO AFTER IGNITION
FEEDALP43
THE STARTER BRIEFLY RUNS BUT THE VEHICLE FAILS TO START
AND GOES INTO AFTER IGNITION FEEDALP44
IMPOSSIBLE TO SHUT OFF ENGINE ALP45
STEERING COLUMN LOCK DOES NOT LOCK ALP46
STEERING COLUMN LOCK DOES NOT UNLOCK ALP47
STARTING ERRATIC ALP48
Page 365 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -365
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -365V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP40 Forced after-ignition feed fails
NOTESCheck the voltage of the battery.
Carry out a fault finding procedure on the function.
Test with the other card.
Switching to + accessories feed should work.
If not deal with ALP39 Accessories feed not activated first.
It can be checked while trying to activate after ignition feed if the verlog indicator light:
–Remains on, meaning that the steering lock is not recognised.
–Remains on for 3 seconds and flashes at 4 Hz, meaning the card is not recognised.
Review of the procedure for forcing after ignition feed:
+ accessories supply off, card in the card reader, starting conditions not met and after
pressing and holding the Start button (approximately 5 seconds).
Make sure that there is no Insert card message on the instrument panel.
Check that status ET008 Blank UCH is NO.
Refer to the procedure for this status if necessary (Blank UCH).
Check that status ET110 UCH request to UPC or injection becomes + after ignition feed after a request for
forced after ignition.
If everything is correct, run fault finding on the UPC.
Make sure the steering column lock functions properly by checking in particular that:
–statuses:
–ET071 Steering column lock blank is NO.
–ET072 Steering column lock is UNLOCKED.
–ET073 Steering column lock sensor signal is UNLOCKED.
See the procedure for these statuses if necessary.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP40 /UCH_V48_ALP40/UCH_V4C_ALP40/
UCH_V4D_ALP40/UCH_V4F_ALP40/UCH_V50_ALP40
Page 366 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -366
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -366V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP41The vehicle does not start and the after ignition feed fails with the
card in the card reader
NOTESCheck the voltage of the battery.
First carry out a function fault finding check.
Switching to + accessories feed should work.
If not deal with ALP39 Accessories feed not activated first.
Check that the start-up conditions are met:
It can be checked while attempting to start if the immobiliser warning light:
–Remains on, meaning that the steering lock is not recognised.
–Remains on for 3 seconds and flashes at 4 Hz, meaning the card is not recognised.
It can also be checked while trying to start; if the Start button flashes, the card
has not been detected or recognised.
If the message "Insert card" is displayed on the instrument panel.
Insert the card in the card reader and run the special command SC005 Check card:
If the message "The inserted card cannot be detected or is not fully inserted into the card reader.
Check the card and the condition of the card reader. If the fault is still present, consult the fault finding for the
customer complaint in the fault finding manual (ALP41 for MEGANE II and ALP21 for CLIO III)" appears, try one
of the other vehicle's cards or a card from another MEGANE II vehicle.
–If the message appears again, apply the fault finding procedure for DEF014 Card reader circuit CC.0.
–If the message has disappeared and the result of the test is accessible, replace the defective card.
Check that status ET120 Card recognised by vehicle is definitely YES:
If ET120 Card recognised by vehicle is NO, the card does not belong to the vehicle or is damaged.
Check that status ET012 Card allocated to vehicle is definitely YES:
If ET012 Card allocated to vehicle is NO, the card is no longer allocated to the vehicle: re-allocate the vehicle's
cards using the special command SC006 Card allocation.
If the fault is still present, contact the Techline.
If the message "Insert card" is not displayed on the instrument panel.
Make sure statuses:
–ET008 Blank central unit is NO.
–ET071 Steering column lock blank is NO
See the procedure for these statuses if necessary.
Check that status ET110 UCH request to injection or UPC becomes START after a starting request is made
when the start conditions are met.
If everything is correct, run fault finding on the UPC.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP41 /UCH_V48_ALP41/UCH_V4C_ALP41/
UCH_V4D_ALP41/UCH_V4F_ALP41/UCH_V50_ALP41
Page 371 of 391
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -371
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding - Fault Finding Chart
87B
87B -371V9 MR-372-J84-87B000$989mif
UCH
Vdiag No.: 44, 48,
4C, 4D, 4F, 50
ALP46 Steering lock fails
NOTESCheck for any faults on the steering lock.
Check the battery voltage. It should be between 9 V and 16 V.
Check the validity of parameter PR008 "Vehicle speed".
Check for any faults in the Airbag computer (impact detected) and ABS/ESP
computers.
Reminder: In hands-free mode, the steering column lock is locked as soon as the
ignition is switched off.
With the card in the reader, the steering column lock is locked after the ignition is
switched off as soon as the card is removed from the reader.
The conditions for a drop in + after ignition feed without the steering column locking are:
–the card is present in the card reader,
–over 20 minutes passing with the card in the card reader after the engine has stopped,
–the vehicle speed is not zero,
–power being requested by the steering column lock too frequently.
With regard to vehicles fitted with UCH computer Vdiag 4F or above:
–the Renault card is removed from the card reader when the vehicle is in forced + after ignition feed,
–3 mins have elapsed following a starting failure due to an engaged gear,
–the Renault card is removed from the card reader following a starting failure due to an engaged gear,
–a front door is open following a starting failure due to an engaged gear and the card is not in the reader.
Check that these conditions are not present.
Check the consistency of statuses ET072 Steering column lock and ET073 Steering column lock signal.
In the event of a fault, see the procedure for these statuses in the UCH section.
Check that the steering column lock belongs to the vehicle using status ET248 Steering column lock immobiliser
code.
If the fault is still present, contact the Techline.
AFTER REPAIRCarry out a complete check with the diagnostic tool.
UCH_V44_ALP46 /UCH_V48_ALP46/UCH_V4C_ALP46/
UCH_V4D_ALP46/UCH_V4F_ALP46/UCH_V50_ALP46