RENAULT SCENIC 2014 J95 / 3.G Petrol Injection - Sagem3000 Workshop Manual

PETROL INJECTION
Fault finding – Conformity check17B
17B - 121V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48PETROL INJECTION
Fault finding – Conformity check
EMISSION CONTROL/OBD SUB-FUNCTION
*OCR: Opening cyclic ratio
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1
Oxygen
sensorET052: Upstream O
2
sensor heatingACTIVE
INACTIVEIn the event of a fault, apply the
interpretation for ET052
Upstream O2 sensor heating.
2ET053: Downstream
O
2 sensor
heatingACTIVE
INACTIVEIn the event of a fault, apply the
interpretation for ET053
Downstream O2 sensor
heating.
3 PR098: Upstream
oxygen sensor
voltage120 mV < PR098
<750mVIf there is a fault, use
interpretation of PR098
Upstream oxygen sensor
voltage.
4 PR099: Downstream
oxygen sensor
voltage120 mV < PR099
<750mVIf there is a fault, apply the
interpretation of PR099
Downstream oxygen sensor
voltage.
5
CanisterET050: Canister bleed
controlINACTIVE
NONE
6 PR102: Canister bleed
solenoid valve
OCR*0% <99.61%
7 Flywheel ET581: Petrol misfireYES
NOIfYES, apply the interpretation
for fault DF065 Misfire.
8 Canister AC017: Canister bleed
solenoid valveThe canister bleed
solenoid valve
should be heard
operatingIn the event of a fault, apply
interpretation of AC017 Canister
bleed solenoid valve.
JSAA741.0
MR-372-J84-17B000$495.mif

PETROL INJECTION
Fault finding – Conformity check17B
17B - 122V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
EMISSION CONTROL/OBD SUB-FUNCTION (continued)
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
9
Oxygen
sensorAC018: Upstream O
2
sensor heatingThe upstream
oxygen sensor
should heat upIn the event of a fault, apply the
interpretation for DF082
Upstream O2 sensor heating
circuit.
10 AC019: Downstream
O
2 sensor
heatingThe downstream
oxygen sensor
should heat upIn the event of a fault, apply the
interpretation of DF083
Downstream O2 sensor
heating circuit.
11Oil vapour
defreeze
resistorET542: Oil vapour
defreeze
resistorCONNECTED
NOT CONNECTEDIf there is a fault, apply the
interpretation for the fault DF612
Oil vapour defreeze resistor
circuit.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B - 123V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1
Air
conditioningET079: Air conditioning
presentStates whether the vehicle is
fitted with air conditioning or
not.
YES: Air conditioning is
detected by the injection
computer.
NO: Air conditioning is not
detected by the injection
computer.If inconsistent with
the vehicle
equipment, carry
out a multiplex
network test and
apply the relevant
procedure.
2ET088: Compressor
actuation
requestThe injection requests the
UPC (via the multiplex
network) to start the
compressor.
ACTIVE: The multiplex network
must not be defective on the
Automatic transmission, UPC or
UCH systems. The UCH must
send a compressor starting
request to the injection. The
coolant pressure sensor must
not be defective. Satisfactory
engine operating conditions
(coolant temperature, engine
load etc.).
INACTIVE: One of the above
conditions has not been met.NONE
3ET004: Air conditioning
authorisationNon operational information,
intended solely for diagnostic
purposes.
YES: Satisfactory engine
operating conditions (coolant
temperature, engine load etc.).
The vehicle is not in a specific
movement phase (hill start or
stop etc.).
NO: One of the above
conditions has not been fulfilled.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B - 124V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
COLD LOOP SUB-FUNCTION (continued)
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
4Refrigerant
pressurePR037: Refrigerant
pressure2 bar < PR037 < 27 bar
Default value: 0 barIf there is a fault, use the
interpretation for PR037
Coolant pressure.
5 Engine speed PR055: Engine
speedShows the speed of
rotation in rpm.
700 rpm < PR055
< 6500 rpmIn the event of a fault
apply the interpretation for
DF154 Flywheel signal
sensor circuit.
6Motorised
throttleET023: Fast idle
speed
requestUCH requests the injection
system to increase the
idling speed.
ABSENT: The UCH did not
issue a request
PRESENT: The UCH has
issued a requestIf ET023 is inconsistent,
carry out a multiplex
network test using the
diagnostic tool. If the
test is correct check the
UCH
7Coolant
temperaturePR064: Coolant
temperature75 °C < PR064 < 120 °CIf there is a fault use the
interpretation for DF001
Coolant temperature
sensor circuit.
8Vehicle
speedPR089: Vehicle
speedGives the vehicle speed in
mph (km/h). This parameter
is sent to the injection by
the ABS computer via the
multiplex network.If there is a fault use the
interpretation for DF091
Vehicle speed signal.
9Air
conditioningPR125: Power
absorbed by
the air
conditioning
compressor300 W < PR125 < 3000 W NONE
10
GMVET014: Fan unit 1
checkRUNNING
STOPPEDIf ET014 or ET015 are
inconsistent, perform a
multiplex network test
using the diagnostic
tool, then if the test is in
order, see the UPC. 11 ET015: Fan unit 2
checkRUNNING
STOPPED
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B - 125V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
HEATING SUB-FUNCTION:
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Coolant
temperaturePR064: Coolant
temperature75 °C < PR064 < 120 °CIf there is a fault use
the interpretation of
DF001 Coolant
temperature sensor
circuit.
2
RCHET111: RCH number
setThis status indicates that the
injection computer is
preventing any change to the
number of passenger
compartment heating resistors
(RCH) activated (RCH already
activated are not shut down,
but no more can be added).
This limit in the number of RCH
is in response to the vehicle's
requirements (power
availability, torque
requirement, etc.).NONE
3 ET112: RCH cut-offThis status indicates that the
injection computer is inhibiting
all the passenger compartment
heating resistors (RCH) in
response to the vehicle's
requirements (power
availability, torque
requirement, injection or air
conditioning defect mode,
etc.).
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B - 126V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
CRUISE CONTROL/SPEED LIMITER SUB-FUNCTION
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1
Cruise
control/
Speed
limiterET042: Cruise control/
speed limiter.- NOT DETECTED: Vehicle
not equipped with cruise
control/speed limiter function
buttons or after reprogramming
or programming the injection
computer, the switch is in the
rest position.
– INACTIVE: When no buttons
are pressed.
- SPEED LIMITER: Main
switch in speed limiter position.
- CRUISE CONTROL: Main
switch in cruise control
position.In the event of a fault,
apply the interpretation
of status ET042 Cruise
control/Speed limiter.
2 ET703: Cruise control/
speed limiter
buttons- INACTIVE: No cruise control/
speed limiter button is pressed.
- PLUS: When the cruise
control/speed limiter “+” button
is pressed.
- MINUS: When the cruise
control/speed limiter
“-” button is pressed.
- SUSPEND: When the cruise
control/speed limiter “0” button
is pressed.
- RESUME: When the cruise
control/speed limiter “R” button
is pressed.In the event of a fault,
consult the
interpretation of status
ET703 Cruise control/
speed limiter button.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B - 127V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
CRUISE CONTROL/SPEED LIMITER SUB-FUNCTION (CONTINUED 1)
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
3
Brake switchET704: Brake switch
No. 1- ACTIVE (brake pedal
depressed)
- INACTIVE (brake pedal
released)In the event of a fault,
consult the
interpretation of status
ET704 "Brake switch
no. 1".
4 ET705: Brake switch
No. 2- ACTIVE (brake pedal
depressed)
- INACTIVE (brake pedal
released)In the event of a fault,
consult the
interpretation of status
ET705 Brake switch
no. 2.
5Clutch pedal
switchET405: Clutch pedal
switch- ACTIVE
- INACTIVEIn the event of a fault,
consult the
interpretation of status
ET405 "Clutch
switch".
6Cruise
control
setpointPR130: Cruise control
setpointIndicates the reference value
requested by the driver (in mph
(km/h))NONE
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B - 128V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
CRUISE CONTROL/SPEED LIMITER SUB-FUNCTION (CONTINUED 2)
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
7Cruise
control/speed
limiter
deactivationET415: Cruise control/
speed limiter
deactivationNONE: This status is present
on the diagnostic tool when:
– The computer has been
reinitialised.
– The computer has been
reprogrammed.
In the event of a fault,
consult the
interpretation of status
ET415 Cruise
control/speed limiter
deactivation. - STATUS 1: Traction control
request
- STATUS 2: Brake pedal
depressed.
- STATUS 3: Clutch pedal
depressed.
STATUS 4: Suspend button
pressed.
- STATUS 5: Cruise control or
speed limiter monitoring.
- STATUS 6: Gear lever in
neutral (manual gearbox) or N
position (automatic
transmission).
- STATUS 7: Inconsistency
between the request and the
vehicle speed.
- STATUS 8: Automatic
transmission in defect mode.
- STATUS 9: Vehicle speed
monitoring.
- STATUS 10: Monitoring by
injection computer.
1
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B - 129V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
START SUB-FUNCTION
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status
checked or ActionDisplay and
Notes Fault finding
1 Starting ET076: StartingAUTHORISEDThe authorisation to start is
given once the fuel pump is
pressurised and if the
motorised throttle has
completed its stop and limp-
home position programming
phase.
2Actuator relay
controlET048: Actuator relay
controlACTIVE
INACTIVEIf ACTIVE apply the interpretation
of DF084 Actuator relay control
circuit.
3 Battery voltage PR071: Computer
supply
voltage13 V < PR071
<15VIf there is a fault, use
interpretation of PR071
Computer supply voltage.
JSAA741.0

PETROL INJECTION
Fault finding – Conformity check17B
17B - 130V12 MR-372-J84-17B000$495.mif
SAGEM 3000
Program No.: A7
Vdiag No.: 44, 48
PROTECTION SUB-FUNCTION
NOTESOnly check conformity after a full check with the diagnostic tool.
The values shown in this conformity check are given as a guide.
Application conditions: Engine warm, idling.
Order FunctionParameter or Status
checked or ActionDisplay and Notes Fault finding
1Code
programmedET006: Code
programmedIndicates whether
immobiliser code
programmed into
computer.
–YES: Code
programmed
–NO: Code not
programmed into
injection computer.If NO, contact the
Techline
2Engine
immobiliserET003: Engine
immobiliserIndicates the status of the
immobiliser system.
–INACTIVE: The
injection computer has
recognised the
immobiliser code
transmitted by the UCH.
–ACTIVE: the injection
computer does not
recognise the
immobiliser code
transmitted by the UCH.If ET003 is
inconsistent, carry out
a multiplex network
test using the
diagnostic tool. If the
test is correct check
the UCH.
3Impact
detectedET077: Impact
detectedYES
NOIf YES, switch off the
ignition for
10 seconds, then
switch it back on so
the engine can be
restarted. Then clear
any faults.
4 Starting ET076: StartingAUTHORISEDThe authorisation to
start is given once the
fuel pump is
pressurised and if the
motorised throttle has
completed its stop
and limp-home
position programming
phase.
JSAA741.0