SSANGYONG KORANDO 1997 Service Repair Manual

GLASS AND MIRRORS 9L-9
SSANGYONG MY2002
KAA9L160
KAA9L170
FRONT DOOR GLASS
Removal Procedure
1. Remove the door seal trim. Refer to Section 9P,
Doors.
2. Remove the screws that secure the glass to the
window regulator.
3. Remove the glass from the door.
4. Removal procedure should follow the installation
procedure in the reverse order.
Installation Procedure
1. Install the glass in the door and position the glass
within the window regulator.
Notice: Dissimilar metals in direct contact with
each other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
2. Install the glass to the window regulator with the
screws.
Installation Notice
3. Install the door seal trim. Refer to Section 9P,
Doors.
4. Removal procedure should follow the installation
procedure in the reverse order.
Tightening Torque1.96 - 2.94 Nm
(17.50 - 26.25 lb-in)
KAA9L180
FIXED GLASS
Removal and Installation Procedure
1. Remove the exterior B-pillar molding. Refer to
Section 9M, Exterior Trim.
2. Remove the screws that secure the glass to the
window regulator.
3. Remove the glass from the door.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
4. Installation should follow the removal procedure
in the reverse order.
Tightening Torque 7 Nm (62 lb-in)

SSANGYONG MY2002
9L-10 GLASS AND MIRRORS
KAA9L190
KAA9L200
OUTSIDE REARVIEW MIRROR
Removal and Installation Procedure
1. Remove the tweeter inner cover.
2. Remove the screws with the outside rearview
mirror.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
3. Installation should follow the removal procedure
in the reverse order.
INSIDE REARVIEW MIRROR
Removal and Installation Procedure
1. Remove the screw with the inside rearview mirror.
Installation Notice
Dissimilar metals in direct contact with each
other may corrode rapidly. Make sure to use
the correct fasteners to prevent premature
corrosion.
2. Installation should follow the removal procedure
in the reverse order.
Tightening Torque1.4 - 1.7 Nm
(9 lb-in)
Tightening Torque3 - 5 Nm
(27 - 44 lb-in)

GLASS AND MIRRORS 9L-11
SSANGYONG MY2002
SPECIFICATIONS
FASTENER TIGHTENING SPECIFICATIONS
Fixed Glass Door Glass
Front Door
Outside Mirror
Room MirrorApplication
N•m
Lb-FtLb-In
7
1.96 - 2.94
3 - 5
1.4 - 1.7-
1.46 - 2.19
-
-62
17.50 - 26.25
27 - 44
9

SSANGYONG MY2002
9L-12 GLASS AND MIRRORS
SCHEMATIC AND ROUTING DIAGRAMS
DEFROSTER
KAA9L210

GLASS AND MIRRORS 9L-13
SSANGYONG MY2002
INSIDE REAR VIEW MIRROR (DIMMING) & BACKUP LAMP
KAA9L220

Description and Operation..................................9M-2
Emblems and Lettering.......................................9M-2
Mud Guards.......................................................9M-2
Components Locator ...........................................9M-3
Exterior Trim.......................................................9M-3
Repair Instructions...............................................9M-4
On-Vehicle Service Unit Repair...............................9M-4
B-Pillar Molding..................................................9M-4
B-Pillar Cover......................................................9M-4
SECTION 9M
EXTERIOR TRIM
CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a
tool or equipment could easily come in contact with exposed electrical terminals. Disconnecting this cable
will help prevent personal injury and damage to the vehicle. The ignition must also be in LOCK unless
otherwise noted.
TABLE OF CONTENTS
Air Extractor Grille...............................................9M-4
Door Molding......................................................9M-5
Front Wheel Molding...........................................9M-5
Rear Wheel Molding...........................................9M-5
Side Step...........................................................9M-6
C-Pillar Cover......................................................9M-6
Roof Molding......................................................9M-6
Specifications......................................................9M-7
Fastener Tightening Specifications......................9M-7

SSANGYONG MY2002
9M-2 EXTERIOR TRIM
DESCRIPTION AND OPERATION
EMBLEMS AND LETTERING
The emblems and lettering on the vehicle are attached
by adhesive. The company emblem appears on the
hood. The lettering, which appears in several places
on the body of the vehicle, Features the model, the
grade, and the company name.
MUD GUARDS
Front and rear mud guards are optional equipment on
all models. Mud guards will help prevent an excessive
build up of mud on the body.

EXTERIOR TRIM 9M-3
SSANGYONG MY2002
COMPONENTS LOCATOR
EXTERIOR TRIM
1 Rivet
2 B Pillar Cover
3 Air Extractor Grill
4 Air Extractor Grill Tape
5 Door Molding
6 Front Wheel Arch Molding
7 Rear Wheel Arch Molding
8 Side Step
9 Side Step Upper Cover
10 Bolt
11 Wheel Arch Clip12 Garnish Clip
13 Garnish Clip
14 Door Molding Clip
15 Door Molding Clip
16 Clip
17 “C” Pillar Cover
18 Clip
19 Tailgate Garnish
20 Roof Molding
21 Roof Molding Endcap
22 Clip
KAA9M010

SSANGYONG MY2002
9M-4 EXTERIOR TRIM
KAA9M030
KAA9M040
B-PILLAR COVER
Removal and Installation Procedure
1. Remove the B-pillar cover.
2. Installation should follow the removal procedure
in the reverse order.
AIR EXTRACTOR GRILLE
Removal and Installation Procedure
1. Remove the air extractor grille.
2. Installation should follow the removal procedure
in the reverse order.
KAA9M020
ON-VEHICLE SERVICE
UNIT REPAIR
B-PILLAR MOLDING
Removal and Installation Procedure
1. Remove the door guide rail from the door. Refer
to Section 9P, Doors.
2. Remove the screws from the door.
3. Remove the B-pillar molding.
4. Installation should follow the removal procedure
in the reverse order.
REPAIR INSTRUCTIONS

EXTERIOR TRIM 9M-5
SSANGYONG MY2002
KAA9M050
KAA9M060
FRONT WHEEL MOLDING
Removal and Installation Procedure
1. Remove the front combination lamp. Refer to
Section 9B, Lighting System.
2. Remove the front wheel molding screws.
3. Remove the front wheel molding from the body.
4. Installation should follow the removal procedure
in the reverse order.
DOOR MOLDING
Removal and Installation Procedure
1. Remove the door protective molding.
2. Installation should follow the removal procedure
in the reverse order.
REAR WHEEL MOLDING
Removal and Installation Procedure
1. Remove the rear wheel molding screws.
2. Remove the rear wheel molding from the body.
3. Installation should follow the removal procedure
in the reverse order.
KAA9M070