torque SSANGYONG MUSSO 1998 Workshop Repair Manual

1E2-10 M161 ENGINE ELECTRICAL
Ignition Cable and Cable Lay-out
1. Firing Order : 1-3-4-2
2. T1/1 : Connect the cylinder 1 + 4
3. T1/2 : Connect the cylinder 2 + 3
Removal & Installation Procedure
1. Disconnect the battery negative cable.
2. Unscrew the 3 screws and remove the ignition cable duct
cover.
Installation Notice
3. Seperate the cable from the ignition cable and the spark
plug.
4. Remove the 2 bolts from each ignition cable and remove
the ignition cables.
Installation Notice
Install the ignition cable to the cylinder 2 and 4 and connect
the cable from 1 to 4, and from 2 to 3.
- T1/1 : Cylinder 1 and 4
- T1/2 : Cylinder 2 and 3
5. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 9 - 11 Nm
Tightening Torque 9 - 11 Nm

OM600 ENGINE ELECTRICAL 1E3-5
Removal & Installation Procedure
1. Disconnect the negative terminal of battery.
2. Remove the nut (2).
3. Remove the glow plug (4).
4. Install the glow plug (4).
5. Tighten the nut (2).
Tightening Torque 20 Nm
Tightening Torque 4 Nm

OM600 ENGINE ELECTRICAL 1E3-7
Removal & Installation Procedure
1. Disconnect the negative terminal of the battery.
2. Disconnect the plug connection (5).
3. OM 662 Engine
Align the groove of cooling fan with bolt (2) (arrow).
4. Remove the bolts (2, 3) and take out the alternator.
5. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 45 Nm

1F1-36 M162 ENGINE CONTROLS
Location
Engine ECU is located at the inside of cowl side trim in right
bottom of instrument panel of passenger side.
Removal & Installation Procedure
1. Turn the ignition switch to "OFF" position.
2. Disconnect the battery negative cable
3. Remove the cowl side trim form passenger side.
4. Unscrew four securing nuts for ECU from mounting bracket.
Installation Notice
5. Pulling out the ECU from bracket.
6. Disconnect the vehicle side coupling(B).
7. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 9 - 11 Nm

M162 ENGINE CONTROLS 1F1-45
Removal & Installation Procedure
lwhen removing the ECU only
1. Turn the ignition switch to "OFF" position.
2. Disconnect the negative battery cable.
3. Disconnect the couplings from ECU.
4. Unscrew the left and right bolt (3) on bolt (1) and auxiliarly
bracket and remove the auxiliarly bracket from the bracket
assembly (2).
Installation Notice
5. Unscrew the four bolts (5) and disconnect the ECU (6) from
the bracket assenbly.
Installation Notice
6. Installation should follow the removal procedure in the
reverse order.
Tightening Torque6 - 8 Nm
5 - 7 Nm(1)
(3)
Tightening Torque 5 - 7 Nm
8. Unscrew the bolts (5) and disconnect the ECU (6) from the
bracket assenbly.
Installation Notice lWhen Removing the ECU with ABS or ABS/ASR Unit
1. Turn the ignition switch to "OFF" position.
2. Disconnect the negative battery cable.
3. Disconnect the couplings from ECU.
4. Disconnect the coupling from ABS or ABS/ASR unit.
5. Unscrew the bolt (1) and the left and right flange nuts.
6. Remove the ECU with ABS or ABS/ASR unit assembly.
7. Unscrew the left and right bolt (3) on the auxiliary bracket
and remove the auxiliary bracket from the bracket assembly.
Installation Notice
Tightening Torque 6 - 8 Nm
Tightening Torque 5 - 7 Nm
Tightening Torque 5 - 7 Nm
9. Installation should follow the removal procedure in the
reverse order.

M162 ENGINE CONTROLS 1F1-51
Removal & Installation Procedure
1. Discharge the fuel pressure from the fuel pressure test
connector.
2. Disconnect the battery ground cable.
3. Disconnect the vacuum hose from the fuel pressure
regulator.
4. Remove the cable guide.
5. Remove the fuel return and supply line.
Notice
lFor removal, cover around parts with cloths not to be
stained by fuel.
lIn case of checking the injector only, do not remove the
fuel return and supply line.
Installation Notice
6. Remove the six injector connectors.
7. Remove the two left and two right bolts and one center bolt
of the fuel distributor assembly from the intake manifold.
Installation Notice
Tightening Torque25 - 30 Nm
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE CONTROLS 1F1-53
3. If there is no change in fuel pressure and maintain the
following pressure over 30 minutes, it is normal.
Internal Leakage Test
1. Connect the fuel pressure gauge to the fuel pressure test
connector.
2. Stop the engine for approx. 30 minutes and then check the
fuel pressure changes.
Fuel pressure
drops slowly
·Fuel leakage at the
injector
• Faulty fuel pressure
regulator's
diaphragm and O-
ring.
Fuel pressure
drops rapidly• Faulty check valve
in the fuel pump.
Possible Cause Pressure Change
Fuel Pressure(bar) 2.5
Discharging the pressure in fuel system
1. Remove the fuel pressure test connector.
Installation Notice
2. Remove the fuel pressure in fuel system by pressing the
service valve with a clean, pointy tool.
Notice
Place a cloth so that the fuel doesn't stain around.
Tightening Torque 22.5 - 27.5 Nm

M162 ENGINE CONTROLS 1F1-57
FUEL FILTER
1 Fuel Filter
2 Outlet
Removal & Installation Procedure
1. Open the fuel tank cap and remove the fuel tank pressure.
2. Remove the fuel at (2) and in (3).
Installation Notice
Notice
Place the fuel pump pad. There may be a corrosion due to
the contact between the fuel filter and the bracket.
4. Check for leaks by operating the engine.
Notice
Installation should follow the removal procedure in the
reverse order. 3. Remove the mounting bracket bolt (4) and remove the fuel
filter (1).
Installation Notice3 Inlet
Tightening Torque
25 - 30 Nm
Tightening Torque
4 - 8 Nm

M162 ENGINE CONTROLS 1F1-65
1 Crankshaft Position Sensor
2 Bolt (M6 X 14)........................................ 9 -11Nm
CRANKSHAFT POSITION SENSOR
Removal & Installation Procedure
1. Disconnect the wiring connector at the crankshaft position
sensor.
2. Unscrew the bolt and remove the crankshaft position sensor
unit.
Installation Notice
3. Installation should follow the removal procedure in the
reverse order.3 Segment
4 Flywheel
Tightening Torque 9 -11Nm

M162 ENGINE CONTROLS 1F1-67
CAMSHAFT POSITION SENSOR
1 Bolt (M6 X 14)......................................... 9-11Nm
2 Camshaft Position Sensor
Removal & Installation Procedure
1. Disconnect the wiring connector from the camshaft position
sensor.
2. Unscrew the bolt (2) and remove the camshaft position
sensor.
Installation Notice3 Shim
5 O-ring
Tightening Torque 9 - 11 Nm
3. Check the clearance and replace the shim if necessary.
4. Check the O-ring for damage and replace it if necessary.
5. Installation should follow the removal procedure in the
reverse order.