ECU SSANGYONG MUSSO 1998 Workshop Manual PDF

M161 ENGINE CONTROLS 1F2-23
Failure
codeItem
Checking method Test
stepRequirement
Specified
valuePossible cause
> 10 MW
11 7 11 8· Ignition:OFF
- Disconnect the
coupling "No.2"
from ECU.Þ 10.1· ·· ·
· Knock
sensor
- Resistance· Connecting
condition
· Cable
· ECU 6 - 8.5 KW
· ·· ·
· Ignition coil
(T1/1, T1/2)
- Secondary
coil
resistance· Remove the high
tension cable of
T1/1, T1/2 Þ 9.1Ignition coil
(T1/1, T1/2)· Ignition coil T1/1
· Ignition coil T1/2
TM.4a
TM.4b
56,

M161 ENGINE CONTROLS 1F2-25
IDLING CONTROL AND ELECTRONIC PEDAL SYSTEM TEST
Þ 2.1· Ignition:ON
50 512.25 - 2.75 V· ·· ·
· Pedal valve
sensor:
- Power
supply
(potentiometer 2)
· Cable
· ECU
Failure
codeItem
Þ 1.0
Checking method
· Ignition:ON
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with
kick down
Test
stepRequirement
Specified
valuePossible cause
31 47
0.2 - 0.5 V
· ·· ·
· Pedal valve
sensor:
- Signal

(potentiometer 1)
160,
161,
164,
167,
4.3 - 4.8 V
· Þ 1.1
· Cable
· Pedal valve sensor
Þ 1.1
· Ignition:ON
31 324.75 - 5.25 V· ·· ·
· Pedal valve
sensor:
- Power
supply

(potentiometer 1)
· Cable
· ECU
Þ 2.0
· Ignition:ON
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with
kick down 50 48
0.1 - 0.4 V
· ·· ·
· Pedal valve
sensor:
- Signal

(potentiometer 2)
162,
163,
164,
167,
2.1 - 2.5 V· Þ 2.1
· Cable
· Pedal valve sensor
Þ 3.0
· Engine:in idling
84 87
0.3 - 0.9 V· ·· ·
· Throttle
valve
actuator:
- Signal
Throttle valve
potentiometer
1104,
105,
108,
109,
116,
119,
185,
4.0 - 4.6 V· Þ 3.1
· Cable
· E-GAS actuator
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with
kick down

1F2-26 M161 ENGINE CONTROLS
Failure
codeItem
Checking method Test
stepRequirementSpecified
valuePossible cause
Þ 3.1· Ignition:ON
84 1124.75 - 5.25 V· ·· ·
· Throttle
valve
actuator:
- Power
supply· Cable
· ECU
Þ 4.0
· Ignition:ON
68 670.8 - 2.3 V
The value will
be changed in
1.0 - 2.5V.· ·· ·
· Throttle
valve
actuator:
- Signal
Throttle valve
actuator
motor
voltage
supply104,
105,
108,
109,
116,
119,
185,· ECU
· Cable
· E-GAS actuator
· Engine:in idling
- Coolant
temperature:
> 70 °C 84 85
4.0 - 4.6 V

Throttle valve
potentiometer
2
0.3 - 0.9 V
· Position of
accelerator pedal:
- Closed throttle
position
- Full throttle with
kick down
Throttle
valve
potentiometer
1+2
· Ignition:OFF
< 10 W
Throttle valve
actuator
motor
resistance68 67

1F2-30 M161 ENGINE CONTROLS
FUEL PUMP TEST
Preparation
1 ECU
2 Test Coupling(No.1-60)
3 Test Coupling(No.61-120)
4 Stop Watch
5 Measuring Beaker
Connection of the Equipment
1. Turn the ignition switch to "OFF" position.
2. Connect the test box to the ECU.0 3 Test Box
04 ECU Test Cable
Tools Required
103 589 00 21 00 Pressure Tester
210 589 00 99 00 Adaptor Line
129 589 00 21 00 Test Box
210 589 08 63 00 Ecu Test Cable

1F2-32 M161 ENGINE CONTROLS
INJECTOR TEST
1 ECU
2 Test Coupling(No.1-60)
3 Test Coupling(No.61-120)
4 Measuring Beaker
5 Shop Made Cable
Preparation
0 3 Test Box
04 ECU Test Cable
Connection of the Equipment
1. Connect the test box to the ECU as shown in the figure.
2. Remove the 2-pin coupling from injector.
3. Remove the fuel distributor and injector with a unit. At this
time, do not remove the supply and return line.
4. Connect the shop made cable to the injector with a firing
order.
5. Collect the fuel from injector.
Tools Required
129 589 00 21 00 Test Box
210 589 08 63 00 ECU Test Cable

1F2-34 M161 ENGINE CONTROLS
MAINTENANCE AND REPAIR
ON-VEHICLE SERVICE
ECU
Appearance
1 Cover
2 Plate
3 Connector
4 Flat pin
Vehicle side : number 1 - 12
Engine side : number 61 - 725 Pin
Vehicle side : number 13 - 60
Engine side : number 73 - 120
A Vehicle Connector : Black
B Engine Connector : Gray

M161 ENGINE CONTROLS 1F2-35
Location
Engine ECU is located at the inside of cowl side trim in right
bottom of instrument panel of passenger side.
Removal & Installation Procedure
1. Turn the ignition switch to "OFF" position.
2. Disconnect the battery negative cable
3. Remove the cowl side trim form passenger side.
4. Unscrew four securing nuts for ECU from mounting bracket.
Installation Notice
5. Pulling out the ECU from bracket.
6. Disconnect the vehicle side coupling(B).
7. Installation should follow the removal procedure in the
reverse order.
Tightening Torque 9 - 11 Nm

1F2-36 M161 ENGINE CONTROLS
Pin No.Abbreviation Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20-
TM.50
-
-
GND
-
LSH2
-
LSH1
TM.31
TM.87
TM.30
WFS I/O
WFS O
-
GND
LS1
-
GND
LS2 -
Starter motor TM.50
-
-
Electronic ground
-
Lambda probe 2 heating
-
Lambda probe 1 heating
Power ground TM.31
V-BATTERY TM.87
V-BATTERY TM.30
Immobilizer crypto read
Immobilizer crypto write
-
Lambda probe 1 ground
Lambda probe 1 signal
-
Lambda probe 2 ground
Lambda probe 2 signal
ECU Pin Numbers and Descriptions
Vehecle Connector

1F2-44 M161 ENGINE CONTROLS
Removal & Installation Procedure
· ·· ·
·When removing the ECU only
1. Turn the ignition switch to "OFF" position.
2. Disconnect the negative battery cable.
3. Disconnect the couplings from ECU.
4. Unscrew the left and right bolt (3) on bolt (1) and auxiliarly
bracket and remove the auxiliarly bracket from the bracket
assembly (2).
Installation Notice
5. Unscrew the four bolts (5) and disconnect the ECU (6) from
the bracket assenbly.
Installation Notice
6. Installation should follow the removal procedure in the
reverse order.
Tightening Torque6 - 8 Nm
5 - 7 Nm(1)
(3)
Tightening Torque 5 - 7 Nm
8. Unscrew the bolts (5) and disconnect the ECU (6) from the
bracket assenbly.
Installation Notice · ·· ·
·When Removing the ECU with ABS or ABS/ASR Unit
1. Turn the ignition switch to "OFF" position.
2. Disconnect the negative battery cable.
3. Disconnect the couplings from ECU.
4. Disconnect the coupling from ABS or ABS/ASR unit.
5. Unscrew the bolt (1) and the left and right flange nuts.
6. Remove the ECU with ABS or ABS/ASR unit assembly.
7. Unscrew the left and right bolt (3) on the auxiliary bracket
and remove the auxiliary bracket from the bracket assembly.
Installation Notice
Tightening Torque 6 - 8 Nm
Tightening Torque 5 - 7 Nm
Tightening Torque 5 - 7 Nm
9. Installation should follow the removal procedure in the
reverse order.

M161 ENGINE CONTROLS 1F2-55
Removal & Installation Procedure
1. Remove the O-ring.
Check for damage and replace it if necessary.
2. Remove the injector bracket from the injector.
Installation Notice
Exactly seat the anti-twist lock into the square groove in
injector.
3. Separate the injector from the fuel distributor.
Inspection & Maintenance
Inspection of the Injector operation and spray pattern
1. Connect the contact box to the ECU.
2. Connect the shop made test plug to the injector and place
it into the tank.
3. Position the ignition switch to ON.
4. Connect the pin 63(+) and 69(-) of the contact box with a
test cable.
5. Check the injector spray pattern.
Notice
Replace the injector if the injector spray pattern is abnormal
or the fuel doesn't inject.
Injector Resistance Inspection
1. Remove the injector connector.
2. Measure the injector coil resistance using a resistance
tester.
Notice
Replace the injector if the measured values is out of the
specified values. Check the connector and wire connection
between the ECU and the injector if the measured values
are normal.
Specified Value
14 - 17 W