replace SUBARU FORESTER 2004 Service Manual PDF
[x] Cancel search | Manufacturer: SUBARU, Model Year: 2004, Model line: FORESTER, Model: SUBARU FORESTER 2004Pages: 2870, PDF Size: 38.67 MB
Page 191 of 2870
AB-59
AIRBAG SYSTEM (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK AIRBAG CONTROL MODULE.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB3) from the
airbag control module.
3) Connect the connector (1R) in test harness
R to connector (AB3).
4) Connect the battery ground cable and turn
the ignition switch to ON.
5) Measure the voltage between connector
(2R) in test harness R and chassis ground.
Connector & terminal
(2R) No. 1 (+) — Chassis ground (
−): Is the voltage more than 10 V? Replace the airbag
control module.
Module.>Go to step 2.
2 CHECK AIRBAG MAIN HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the airbag connector (AB1)
from the body harness (B31).
3) Connect the connector (2M) in test harness
M to connector (AB1).
4) Measure the resistance between connector
(5M) in test harness M and the connector (2R)
in test harness R.
Connector & terminal
(5M) No. 2 — (2R) No. 1: Is the resistance less than 10
Ω?Go to step 3.Replace the airbag
main harness with
body harness.
3 CHECK AIRBAG MAIN HARNESS.
Measure the following resistance with the
above-mentioned condition maintained.
Connector & terminal
(5M) No. 2 — Chassis ground:
(2R) No. 1 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 4.Replace the airbag
main harness with
body harness.
4 CHECK FUSE No. 11 (IN JOINT BOX).
1) Confirm that the ignition switch is turned
OFF.
2) Remove the fuse No. 11 (in fuse and relay
box) and perform visual inspection.Is the fuse No. 11 blown out? Replace the fuse
No. 11. If fuse No.
11 blows out
again, repair the
body harness. Repair the body
harness.
Page 193 of 2870
AB-61
AIRBAG SYSTEM (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK AIRBAG CONTROL MODULE.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB3) from the
airbag control module.
3) Connect the connector (1R) in test harness
R to connector (AB3).
4) Connect the battery ground cable and turn
the ignition switch to ON.
5) Measure the voltage between connector
(2R) in test harness R and chassis ground.
Connector & terminal
(2R) No. 1 (+) — Chassis ground (
−): Is the voltage more than 10 V? Replace the airbag
control module.
Module.>Go to step 2.
2 CHECK AIRBAG MAIN HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the airbag connector (AB1)
from the body harness (B31).
3) Connect the connector (2M) in test harness
M to connector (AB1).
4) Measure the resistance between connector
(5M) in test harness M and the connector (2R)
in test harness R.
Connector & terminal
(5M) No. 9 — (2R) No. 1: Is the resistance less than 10
Ω?Go to step 3.Replace the airbag
main harness with
body harness.
3 CHECK AIRBAG MAIN HARNESS.
Measure the following resistance with the
above-mentioned condition maintained.
Connector & terminal
(5M) No. 9 — Chassis ground:
(2R) No. 1 — Chassis ground: Is the resistance more than 1
MΩ? Go to step 4.Replace the airbag
main harness with
body harness.
4 CHECK FUSE No. 11 (IN FUSE AND RELAY
BOX).
1) Confirm that the ignition switch is turned
OFF.
2) Remove the fuse No. 11 (in fuse and relay
box) and perform visual inspection.Fuse No. 11 is not blown out. Replace the fuse
No. 11. If fuse No.
11 blows out
again, repair the
body harness. Repair the body
harness.
Page 195 of 2870
AB-63
AIRBAG SYSTEM (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK AIRBAG CONTROL MODULE.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB3) from air-
bag control module.
3) Connect the connector (1R) in test harness
R to connector (AB3).
4) Connect the battery ground cable, and turn
the ignition switch to ON.
5) Measure the voltage between the connec-
tor (2R) in test harness R and the chassis
ground.
Connector & terminal
(2R) No. 6 (+) — Chassis ground (
−): Is the voltage more than 10 V? Replace the airbag
control module.
Module.>Go to step 2.
2 CHECK AIRBAG MAIN HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the airbag connector (AB1)
from the body harness (B31).
3) Connect the connector (2M) in test harness
M to the airbag connector (AB1).
4) Measure the resistance between the con-
nector (5M) in test harness M and the connec-
tor (2R) in test harness R.
Connector & terminal
(5M) No. 4 — (2R) No. 6: Is the resistance less than 10
Ω?Go to step 3.Replace the airbag
main harness with
body harness.
3 CHECK AIRBAG MAIN HARNESS.
Measure the following resistance with the
above-mentioned condition maintained.
Connector & terminal
(5M) No. 4 — Chassis ground:
(2R) No. 6 — Chassis ground: Is the resistance more than 1
MΩ?Go to step 4.Replace the airbag
main harness with
body harness.
4 CHECK FUSE NO. 6 (IN FUSE AND RELAY
BOX).
1) Confirm that the ignition switch is turned
OFF.
2) Remove the No. 6 fuse (in fuse and relay
box) and perform visual inspection.Is the fuse No. 6 blown out? Replace the fuse
No. 6. If fuse No. 6
is blown out again,
repair the body
harness. Repair the body
harness.
Page 197 of 2870
AB-65
AIRBAG SYSTEM (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK AIRBAG CONTROL MODULE.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB3) from air-
bag control module.
3) Connect the connector (1R) in test harness
R to connector (AB3).
4) Connect the battery ground cable, and turn
the ignition switch to ON.
5) Measure the voltage between the connec-
tor (2R) in test harness R and the chassis
ground.
Connector & terminal
(2R) No. 6 (+) — Chassis ground (
−): Is the voltage more than 10 V? Replace the airbag
control module.
Module.>Go to step 2.
2 CHECK AIRBAG MAIN HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the airbag connector (AB1)
from the body harness (B31).
3) Connect the connector (2M) in test harness
M to the airbag connector (AB1).
4) Measure the resistance between the con-
nector (5M) in test harness M and the connec-
tor (2R) in test harness R.
Connector & terminal
(5M) No. 4 — (2R) No. 6: Is the resistance less than 10
Ω?Go to step 3.Replace the airbag
main harness with
body harness.
3 CHECK AIRBAG MAIN HARNESS.
Measure the following resistance with the
above-mentioned condition maintained.
Connector & terminal
(5M) No. 1 — Chassis ground:
(2R) No. 6 — Chassis ground: Is the resistance more than 1
MΩ? Go to step 4.Replace the airbag
main harness with
body harness.
4 CHECK FUSE NO. 6 (IN FUSE AND RELAY
BOX).
1) Confirm that the ignition switch is turned
OFF.
2) Remove the No. 6 fuse (in fuse and relay
box) and perform visual inspection.Is the fuse No. 6 blown out? Replace the fuse
No. 6. If fuse No. 6
is blown out again,
repair the body
harness. Repair the body
harness.
Page 199 of 2870
AB-67
AIRBAG SYSTEM (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK FRONT SUB-SENSOR (RH) AND
AIRBAG HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB3) from the
airbag control module, and connect the con-
nector (1R) in test harness R.
3) Measure the resistance of the connector
(3R) in test harness R.
Connector & terminal
(3R) No. 7 — (3R) No. 9: Is the resistance 750 Ω and 1
KΩ? Replace the airbag
control module.
Module.>Go to step 2.
2 CHECK AIRBAG MAIN HARNESS AND
FRONT SUB-SENSOR HARNESS (RH).
1) Disconnect the connector (AB15) from the
front sub-sensor.
2) Connect the connector (IH) in test harness
H to connector (AB15).
3) Measure the resistance between connector
(3R) in test harness R and connector (3H) in
test harness H.
Connector & terminal
(3R) No. 7 — (3H) No. 5:
(3R) No. 9 — (3H) No. 6: Is the resistance less than 10
Ω?Go to step 3.LHD model:
Replace the airbag
main harness and
front sub-sensor
harness with body
harness.
RHD model:
Go to step 4.
3 CHECK AIRBAG MAIN HARNESS AND
FRONT SUB-SENSOR HARNESS (RH).
Measure the resistance between connector
(3R) in test harness R and the chassis ground.
Connector & terminal
(3R) No. 7 — Chassis ground:
(3R) No. 9 — Chassis ground: Is the resistance more than 1
MΩ?Go to step 8.LHD model:
Replace the airbag
main harness and
front sub-sensor
harness with body
harness.
RHD model:
Go to step 4.
4 CHECK AIRBAG MAIN HARNESS
1) Disconnect the connector (AB13) from
(AB14), and connect the connector (1L) in test
harness L to connector (AB13).
2) Measure the resistance between connector
(3R) in test harness R and connector (3L) in
test harness L.
Connector & terminal
(3R) No. 7 — (3L) No. 4:
(3R) No. 9 — (3L) No. 3: Is the resistance less than 10
Ω?Go to step 5.Replace the airbag
main harness with
body harness.
5 CHECK AIRBAG MAIN HARNESS
Measure the resistance between connector
(3R) in test harness R and the chassis ground.
Connector & terminal
(3R) No. 7 — Chassis ground:
(3R) No. 9 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 6.Replace the airbag
main harness with
body harness.
6 CHECK FRONT SUB-SENSOR HARNESS
(RH).
1) Connect the connector (2L) in test harness
F to the connector (AB14).
2) Measure the resistance between connector
(3H) in test harness H and connector (3L) in
the test harness L.
Connector & terminal
(3L) No. 5 — (3H) No. 5:
(3L) No. 6 — (3H) No. 6: Is the resistance less than 10
Ω?Go to step 7.Replace the front
sub-sensor har-
ness (RH) with
body harness.
Page 200 of 2870
AB-68
AIRBAG SYSTEM (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
7 CHECK FRONT SUB-SENSOR HARNESS
(RH).
Measure the resistance between connector
(3L) in test harness L and the chassis ground.
Connector & terminal
(3L) No. 5 — Chassis ground:
(3L) No. 6 — Chassis ground: Is the resistance more than 1
MΩ?Go to step 8.Replace the front
sub-sensor har-
ness (RH) with
body harness.
8 CHECK FRONT SUB-SENSOR (RH).
1) Connect the connector (2H) in test harness
H to front sub-sensor (RH).
2) Measure the resistance of the connector
(3H) in test harness H.
Connector & terminal
(3H) No. 3 — No. 4: Is the resistance 750 Ω and 1
KΩ?Go to step 9.Replace the front
sub-sensor (RH).
sor.>
9 CHECK FRONT SUB-SENSOR (RH).
Measure the resistance between connector
(3H) in test harness H and the chassis ground.
Connector & terminal
(3H) No. 3 — Chassis ground:
(3H) No. 4 — Chassis ground:Is the resistance more than 1
MΩ?Finish the diagno-
sis.Replace the front
sub-sensor (RH).
sor.> Step Check Yes No
Page 202 of 2870
AB-70
AIRBAG SYSTEM (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK FRONT SUB-SENSOR (LH) AND
AIRBAG HARNESS.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB3) from the
airbag control module, and connect connector
(1R) in the test harness R to connector (AB3).
3) Measure the resistance of the connector
(3R) in the test harness R.
Connector & terminal
(3R) No. 6 — (3R) No. 8: Is the resistance 750 Ω and 1
KΩ?Replace the airbag
control module.
Module.>Go to step 2.
2 CHECK AIRBAG MAIN HARNESS AND
FRONT SUB-SENSOR HARNESS (LH).
1) Disconnect the connector (AB18) from the
front sub-sensor.
2) Connect the connector (1H) in test harness
H to connector (AB18).
3) Measure the resistance between connector
(3R) in test harness R and connector (3H) in
test harness H.
Connector & terminal
(3R) No. 6 — (3H) No. 5:
(3R) No. 8 — (3H) No. 6: Is the resistance less than 10
Ω?Go to step 3.LHD model:
Go to step 4.
RHD model:
Replace the airbag
main harness and
front sub-sensor
harness with body
harness.
3 CHECK AIRBAG MAIN HARNESS AND
FRONT SUB-SENSOR HARNESS (LH).
Measure the resistance between connector
(3R) in test harness R and the chassis ground.
Connector & terminal
(3R) No. 6 — Chassis ground:
(3R) No. 8 — Chassis ground: Is the resistance more than 1
MΩ?Go to step 8.LHD model:
Go to step 4.
RHD model:
Replace the airbag
main harness and
front sub-sensor
harness with body
harness.
4 CHECK AIRBAG MAIN HARNESS
1) Disconnect the connector (AB13) from
(AB14), and connect the connector (1L) in test
harness L to connector (AB13).
2) Measure the resistance between connector
(3R) in test harness R and connector (3L) in
test harness L.
Connector & terminal
(3R) No. 6 — (3L) No. 4:
(3R) No. 8 — (3L) No. 3: Is the resistance less than 10
Ω?Go to step 5.Replace the airbag
main harness with
body harness.
5 CHECK AIRBAG MAIN HARNESS
Measure the resistance between connector
(3R) in test harness R and the chassis ground.
Connector & terminal
(3R) No. 6 — Chassis ground:
(3R) No. 8 — Chassis ground:Is the resistance more than 1
MΩ?Go to step 6.Replace the airbag
main harness with
body harness.
6 CHECK FRONT SUB-SENSOR HARNESS
(LH).
1) Connect the connector (2L) in test harness
L to the connector (AB14).
2) Measure the resistance between connector
(3H) in test harness H and connector (3L) in
the test harness L.
Connector & terminal
(3L) No. 5 — (3H) No. 5:
(3L) No. 6 — (3H) No. 6: Is the resistance less than 10
Ω?Go to step 7.Replace the front
sub-sensor har-
ness (LH) with
body harness.
Page 203 of 2870
AB-71
AIRBAG SYSTEM (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
7 CHECK FRONT SUB-SENSOR HARNESS
(LH).
Measure the resistance between connector
(3L) in test harness L and the chassis ground.
Connector & terminal
(3L) No. 5 — Chassis ground:
(3L) No. 6 — Chassis ground: Is the resistance more than 1
MΩ?Go to step 8.Replace the front
sub-sensor har-
ness (LH) with
body harness.
8 CHECK FRONT SUB-SENSOR (LH).
1) Connect the connector (2H) in test harness
H to front sub-sensor (LH).
2) Measure the resistance of the connector
(3H) in test harness H.
Connector & terminal
(3H) No. 3 — (3H) No. 4: Is the resistance 750 Ω and 1
KΩGo to step 9.Replace the front
sub-sensor (LH).
sor.>
9 CHECK FRONT SUB-SENSOR (LH).
Measure the resistance between connector
(3H) in test harness H and the chassis ground.
Connector & terminal
(3H) No. 3 — Chassis ground:
(3H) No. 4 — Chassis ground:Is the resistance more than 1
MΩ?Finish the diagno-
sis.Replace the front
sub-sensor (LH).
sor.> Step Check Yes No
Page 205 of 2870
AB-73
AIRBAG SYSTEM (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK SIDE AIRBAG MODULE.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB11) from side
airbag module (RH), and connect the connec-
tor (1F) in test harness F to (AB11).
3) Connect the airbag resistor to connector
(3F) in test harness F.
4) Connect the battery ground cable, and turn
the ignition switch to ON.Is the airbag warning light
turned on normally?Replace the front
seat with side air-
bag module (RH).
2 CHECK SIDE AIRBAG HARNESS (RH).
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB26) from the
seat belt pretensioner (RH).
3) For the vehicle with lap seat belt preten-
sioner, disconnect the connector (AB25) from
lap pretensioner.
4) Disconnect the airbag resistor from test
harness F.
5) Disconnect the connector (AB8) from air
bag control module.
6) Connect the connector (1R) in test harness
R to connector (AB8).
7) Measure the resistance between connector
(3R) in test harness R and connector (3F) in
test harness F.
Connector & terminal
(3R) No. 18 — (3F) No. 3:
(3R) No. 20 — (3F) No. 4: Is the resistance less than 10
Ω?Go to step 3.Replace the side
airbag harness
with body harness.
3 CHECK SIDE AIRBAG HARNESS (RH).
Measure the resistance of the connector (3R)
in test harness R.
Connector & terminal
(3R) No. 18 — (3R) No. 20: Is the resistance more than 1
MΩ?Go to step 4.Replace the side
airbag harness
with body harness.
4 CHECK SIDE AIRBAG HARNESS (RH).
Measure the resistance between connector
(3R) in test harness R and the chassis ground.
Connector & terminal
(3R) No. 18 — Chassis ground:
(3R) No. 20 — Chassis ground: Is the resistance more than 1
MΩ?Replace the airbag
control module.
Module.>Replace the side
airbag harness
with body harness.
Page 207 of 2870
AB-75
AIRBAG SYSTEM (DIAGNOSTIC)
Diagnostic Procedure with Diagnostic Trouble Code (DTC)
Step Check Yes No
1 CHECK SIDE AIRBAG MODULE.
1) Turn the ignition switch to OFF, disconnect
the battery ground cable, and wait more than
20 seconds.
2) Disconnect the connector (AB9) from side
airbag module (LH), and connect the connec-
tor (1F) in test harness F to (AB9).
3) Connect the airbag resistor to connector
(3F) in test harness F.
4) Connect the battery ground cable, and turn
the ignition switch to ON.Is the airbag warning light
turned on normally?Replace the front
seat with side air-
bag module (LH).
2 CHECK SIDE AIRBAG HARNESS (LH).
1) Turn ignition switch to OFF, disconnect the
battery ground cable, and wait more than 20
seconds.
2) Disconnect the connector (AB19) from the
seat belt pretensioner (LH).
3) Disconnect the airbag resistor from the test
harness.
4) Disconnect the connector (AB7) from the
airbag control module.
5) Connect the connector (1R) in test harness
R to connector (AB7).
6) Measure the resistance between connector
(3R) in test harness R and connector (3F) in
test harness F.
Connector & terminal
(3R) No. 12 — (3F) No. 4:
(3R) No. 10 — (3F) No. 3: Is the resistance less than 10
Ω?Go to step 3.Replace the side
airbag harness
with body harness.
3 CHECK SIDE AIRBAG HARNESS (LH).
Measure the resistance of the connector (3R)
in test harness R.
Connector & terminal
(3R) No. 12 — (3R) No. 10: Is the resistance more than 1
MΩ?Go to step 4.Replace the side
airbag harness
with body harness.
4 CHECK SIDE AIRBAG HARNESS (LH).
Measure the resistance between connector
(3R) in test harness R and the chassis ground.
Connector & terminal
(3R) No. 10 — Chassis ground:
(3R) No. 12 — Chassis ground: Is the resistance more than 1
MΩ?Replace the airbag
control module.
Module.>Replace the side
airbag harness
with body harness.