SUZUKI SWIFT 2000 1.G Transmission Service Workshop Manual

AIR BAG SYSTEM 10B-27
Fig. for STEP 3
Special tool
(A) : 09932-76010
(B) : 09932-75010
DTC B1019:
Fig. for STEP 1, 2 and 3
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Clear diagnostic trouble codes (Refer to DTC CLEARANCE), if any.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.
Step Action Yes No
1 1) With ignition switch OFF, disconnect passenger
air bag (inflator) module connector behind the
glove box.
2) Check proper connection to passenger air bag
(inflator) module at terminals in “Q03” connector.
3) If OK then connect Special Tool (B) to passenger
air bag (inflator) module connector disconnected
at the step 1).
With ignition switch ON, is DTC B1019 current?Go to step 2. Ignition switch OFF.
Replace passenger air
bag (inflator) module
(Refer to PASSENGER
AIR BAG (INFLATOR)
MODULE in this section).
2 1) With ignition switch OFF, disconnect Special Tool
(B) and SDM.
2) Measure voltage from “Q06-7” terminal to body
ground.
With ignition switch ON, is voltage 1 V or less?Go to step 3. Repair short from “BLU/
RED” wire circuit to power
circuit.
3 1) Measure voltage from “Q06-8” terminal to body
ground.
With ignition switch ON, is voltage 1 V or less?Substitute a known-
good SDM and
recheck.Repair short from “YEL/
RED” wire circuit to power
circuit.

10B-28 AIR BAG SYSTEM
Fig. for STEP 2
Fig. for STEP 3
Special tool
(A) : 09932-76010
(B) : 09932-75010
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Clear diagnostic trouble codes (Refer to DTC CLEARANCE), if any.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.

AIR BAG SYSTEM 10B-29
DTC B1021 – DRIVER AIR BAG INITIATOR CIRCUIT RESISTANCE HIGH
DTC B1022 – DRIVER AIR BAG INITIATOR CIRCUIT RESISTANCE LOW
DTC B1024 – DRIVER AIR BAG INITIATOR CIRCUIT SHORT TO GROUND
DTC B1025 – DRIVER AIR BAG INITIATOR CIRCUIT SHORT TO POWER CIR-
CUIT
WIRING DIAGRAM
DTC WILL SET WHEN
DTC B1021 :
The combined resistance of the driver air bag (inflator) module, contact coil assembly, harness wiring and con-
nector terminal contact is above a specified value for specified time.
DTC B1022 :
The combined resistance of the driver air bag (inflator) module, contact coil assembly, harness wiring and con-
nector terminal contact is below a specified value for specified time.
DTC B1024 :
The voltage measured at driver air bag initiator circuit is below a specified value for specified time.
DTC B1025 :
The voltage measured at driver air bag initiator circuit is above a specified value for specified time.
TABLE TEST DESCRIPTION
DTC B1021, B1022, B1024 and B1025 :
STEP 1 : Check whether malfunction is in contact coil and driver air bag (inflator) module or the others.
STEP 2 : Check driver air bag (inflator) module initiator circuit in air bag harness.
STEP 3 : Check whether malfunction is in contact coil or driver air bag (inflator) module.
[A] : Shorting bar 2. Ignition switch 5. Contact coil assembly
[B] : Airbag harness 3.“AIR BAG” fuse 6. Driver air bag (inflator) module
1. From main fuse 4. SDM 7. Ground for air bag system
1
2RED BLK/YELRED
3
7
BLK“Q06”
Q06-4
Q06-17IG
GND4
“G39”“Q02”
[A]
[B]
GRN/RED
GRN Q06-10
Q06-9 D- D+“Q01”
“Q06”
“Q08”6
5
CAUTION:
Be sure to perform AIR BAG DIAGNOSTIC SYSTEM CHECK before starting diagnosis according to flow
table.
When measurement of resistance or voltage is required in this table, use a tester along with a correct termi-
nal adapter from special tool (Connector test adapter kit).
When a check for proper connection is required, refer to INTERMITTENT AND POOR CONNECTIONS in
this section.
If there is open circuit in the air bag wire harness, connector or terminal is found damaged, replace the wire
harness, connector and terminal as an assembly.

10B-30 AIR BAG SYSTEM
DIAGNOSTIC FLOW TABLE
DTC B1021 :
Fig. for STEP 1 and 2
Fig. for STEP 2Step Action Yes No
1 1) With ignition switch OFF, disconnect contact coil con-
nector located near the base of the steering column.
2) Check proper connection to contact coil at terminals
in “Q01” connector.
3) If OK then connect Special Tool (B) to contact coil
connector disconnected at step 1).
With ignition switch ON, is DTC B1021 current?Go to step 2. Go to step 3.
2 1) With ignition switch OFF, disconnect SDM.
2) Check proper connection to SDM at terminals “Q06-9”
and “Q06-10”.
3) If OK then measure resistance between “Q06-9” and
“Q06-10” terminals with connected Special Tool (B).
Is resistance 4.5 Ω or less?Substitute a known-
good SDM and
recheck.Repair high resis-
tance or open in
“GRN” or “GRN/RED”
wire circuit.
3 1) With ignition switch OFF, disconnect Special Tool (B)
then reconnect contact coil connector located near
the base of the steering column.
2) Remove driver air bag (inflator) module from steering
wheel (Refer to DRIVER AIR BAG (INFLATOR)
MODULE in Section 3C).
3) Check proper connection to driver air bag (inflator)
module at terminals in “Q08” connector.
4) If OK then connect Special Tool (B) to “Q08” connec-
tor.
With ignition switch ON, is DTC B1021 current?Ignition switch OFF.
Replace contact coil
assembly (Refer to
COMBINATION
SWITCH/CON-
TACT COIL AND
COMBINATION
SWITCH ASSEM-
BLY in Section 3C).Ignition switch OFF.
Replace driver air
bag (inflator) module
(Refer to DRIVER
AIR BAG (INFLA-
TOR) MODULE in
Section 3C).
BASE OF
COLUMN
“Q01”

AIR BAG SYSTEM 10B-31
Fig. for STEP 3
Special tool
(A) : 09932-76010
(B) : 09932-75010
DTC B1022 :
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Clear diagnostic trouble codes (Refer to DTC CLEARANCE), if any.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.
Step Action Yes No
1 1) With ignition switch OFF, disconnect con-
tact coil connector located near the base of
the steering column.
2) Check proper connection to contact coil at
terminals in “Q01” connector.
3) If OK then connect Special Tool (B) to con-
tact coil connector disconnected at step 1).
With ignition switch ON, is DTC B1022 current?Go to step 2. Go to step 3.
2 1) With ignition switch OFF, disconnect SDM.
2) Check proper connection to SDM at termi-
nals “Q06-9” and “Q06-10”.
3) If OK then measure resistance between
“Q06-9” and “Q06-10” terminals with con-
nected Special Tool (B).
Is resistance 1.7 Ω or more?Substitute a known-good
SDM and recheck.Repair short from “GRN”
wire circuit to “GRN/RED”
wire circuit or from “GRN”
or “GRN/RED” wire cir-
cuit to other wire circuit.
3 1) With ignition switch OFF, disconnect Spe-
cial Tool (B) then reconnect contact coil
connector located near the base of the
steering column.
2) Remove driver air bag (inflator) module
from steering wheel (Refer to DRIVER AIR
BAG (INFLATOR) MODULE in Section 3C).
3) Check proper connection to driver air bag
(inflator) module at terminals in “Q08” con-
nector.
4) If OK then connect Special Tool (B) to “Q08”
connector.
With ignition switch ON, is DTC B1022 current?Ignition switch OFF.
Replace contact coil
assembly (Refer to COM-
BINATION SWITCH/
CONTACT COIL AND
COMBINATION SWITCH
ASSEMBLY in Section
3C).Ignition switch OFF.
Replace driver air bag
(inflator) module (Refer to
DRIVER AIR BAG
(INFLATOR) MODULE in
Section 3C).

10B-32 AIR BAG SYSTEM
Fig. for STEP 1 and 2
Fig. for STEP 2
Fig. for STEP 3
Special tool
(A) : 09932-76010
(B) : 09932-75010
BASE OF
COLUMN
“Q01”
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Clear diagnostic trouble codes (Refer to DTC CLEARANCE), if any.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.

AIR BAG SYSTEM 10B-33
DTC B1024 :
Fig. for STEP 1 and 2
Fig. for STEP 2Step Action Yes No
1 1) With ignition switch OFF, disconnect contact coil
connector located near the base of the steering col-
umn.
2) Check proper connection to contact coil at terminals
in “Q01” connector.
3) If OK then connect Special Tool (B) to contact coil
connector disconnected at step 1).
With ignition switch ON, is DTC B1024 current?Go to step 2. Go to step 3.
2 1) With ignition switch OFF, disconnect Special Tool
(B) and SDM.
2) Measure resistance between “Q06-9” terminal and
body ground and between “Q06-10” terminal and
body ground.
Are they 10 Ω or more?Substitute a known-
good SDM and
recheck.Repair short from
“GRN” or “GRN/RED”
wire circuit to ground.
3 1) With ignition switch OFF, disconnect Special Tool
(B) then reconnect contact coil connector located
near the base of the steering column.
2) Remove driver air bag (inflator) module from steer-
ing wheel (Refer to DRIVER AIR BAG (INFLATOR)
MODULE in Section 3C).
3) Check proper connection to driver air bag (inflator)
module at terminals in “Q08” connector.
4) If OK then connect Special Tool (B) to “Q08” con-
nector.
With ignition switch ON, is DTC B1024 current?Ignition switch OFF.
Replace contact coil
assembly (Refer to
COMBINATION
SWITCH/CONTACT
COIL AND COMBI-
NATION SWITCH
ASSEMBLY in Sec-
tion 3C).Ignition switch OFF.
Replace driver air bag
(inflator) module
(Refer to DRIVER AIR
BAG (INFLATOR)
MODULE in Section
3C).
BASE OF
COLUMN
“Q01”

10B-34 AIR BAG SYSTEM
Fig. for STEP 3
Special tool
(A) : 09932-76010
(B) : 09932-75010
DTC B1025 :
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Clear diagnostic trouble codes (Refer to DTC CLEARANCE), if any.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.
Step Action Yes No
1 1) With ignition switch OFF, disconnect con-
tact coil connector located near the base of
the steering column.
2) Check proper connection to contact coil at
terminals in “Q01” connector.
3) If OK then connect Special Tool (B) to con-
tact coil connector disconnected at step 1).
With ignition switch ON, is DTC B1025 current?Go to step 2. Go to step 3.
2 1) With ignition switch OFF, disconnect Spe-
cial Tool (B) and SDM.
2) Measure voltage from “ Q06-9” terminal to
body ground and from “Q06-10” terminal to
body ground.
With ignition switch ON, are they 1 V or less?Substitute a known-good
SDM and recheck.Repair short from “GRN”
or “GRN/RED” wire cir-
cuit to power circuit.
3 1) With ignition switch OFF, disconnect Spe-
cial Tool (B) then reconnect contact coil
connector located near the base of the
steering column.
2) Remove driver air bag (inflator) module
from steering wheel (Refer to DRIVER AIR
BAG (INFLATOR) MODULE in Section 3C).
3) Check proper connection to driver air bag
(inflator) module at terminals in “Q08” con-
nector.
4) If OK then connect Special Tool (B) to “Q08”
connector.
With ignition switch ON, is DTC B1025 current?Ignition switch OFF.
Replace contact coil
assembly (Refer to COM-
BINATION SWITCH/
CONTACT COIL AND
COMBINATION SWITCH
ASSEMBLY in Section
3C).Ignition switch OFF.
Replace driver air bag
(inflator) module (Refer to
DRIVER AIR BAG
(INFLATOR) MODULE in
Section 3C).

AIR BAG SYSTEM 10B-35
Fig. for STEP 1 and 2
Fig. for STEP 2
Fig. for STEP 3
Tightening torque
(A) : 09932-76010
(B) : 09932-75010
BASE OF
COLUMN
“Q01”
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Clear diagnostic trouble codes (Refer to DTC CLEARANCE), if any.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.

10B-36 AIR BAG SYSTEM
DTC B1032 – POWER SOURCE VOLTAGE LOW
WIRING DIAGRAM
DTC WILL SET WHEN
The power source voltage is below an approx. 8 V for specified time.
TABLE TEST DESCRIPTION
STEP 1 : Check if voltage applied to SDM is within normal range.
STEP 2 : Check if DTC 32 still exists.
DIAGNOSTIC FLOW TABLE
[A] : Air bag harness 2. Ignition switch 4. SDM
1. From main fuse 3.“AIR BAG” fuse 5. Ground for air bag system
1
2RED BLK/YELRED
3
5
BLK“Q06”
Q06-4
Q06-17IG
GND4
“G39”“Q02”
[A]
CAUTION:
Be sure to perform AIR BAG DIAGNOSTIC SYSTEM CHECK before starting diagnosis according to
flow table.
When measurement of resistance or voltage is required in this table, use a tester along with a cor-
rect terminal adapter from special tool (Connector test adapter kit).
When a check for proper connection is required, refer to INTERMITTENT AND POOR CONNEC-
TIONS in this section.
If there is open circuit in the air bag wire harness, connector or terminal is found damaged, replace
the wire harness, connector and terminal as an assembly.
Step Action Yes No
1 1) Measure voltage on battery.
Is voltage 11 V or more?Go to step 2. Check Charging System
and repair as necessary.
(Refer to DIAGNOSIS in
Section 6H)
2 1) With ignition switch OFF, disconnect SDM.
2) Check proper connection to SDM at “Q06-4”
terminal.
3) If OK then ignition switch ON, and then
check voltage from “Q06-4” terminal on
SDM connector to body ground.
Is voltage 8 V or more?Go to step 4. Go to step 3.