torque TOYOTA RAV4 2006 Service Owner's Guide

PREPARATION – 2GR-FE LUBRICATIONPP–25
PP
EQUIPMENT
Container -
Deep socket wrench (24 mm) -
Hose Oil filter
Oil pressure gauge -
Socket wrench (27 mm) -
Straightedge -
Torque wrench -
Wooden block -

PREPARATION – U140F AUTOMATIC TRANSAXLEPP–53
PP
EQUIPMENT
Straight edge -
Vernier calipers -
Dial indicator or dial indicator with magnetic base -
Torque wrench -
Feeler gauge -
Plastic-faced hammer -
Press -
Seal packing 2403, THREE BOND 2403 or equivalent -

PP–80PREPARATION – STEERING COLUMN
PP
EQUIPMENT
Torque wench -
Drill -

PREPARATION – POWER STEERINGPP–81
PP
EQUIPMENT
Torque wrench -

PREPARATION – SUPPLEMENTAL RESTRAINT SYSTEMPP–85
PP
EQUIPMENT
Bolt
Length: 35.0 mm (1.378 in.)
Pitch: 1.0 mm (0.039 in.)
Diameter: 6.0 mm (0.236 in.)Airbag disposal
Plastic bag Airbag disposal
Tire
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)Airbag disposal
Tire with disc wheel
Width: 185 mm (7.28 in.)
Inner diameter: 360 mm (14.17 in.)Airbag disposal
Torque wrench -

U140F AUTOMATIC TRANSAXLE – VALVE BODYAX–253
AX
REASSEMBLY
1. INSTALL MANUAL VALVE
(a) Install the manual valve to the valve body.
2. INSTALL SHIFT SOLENOID VALVE S4
(a) Install the shift solenoid valve S4 to the valve body
with the bolt.
Torque: 11 N*m (112 kgf*cm, 9 ft.*lbf)
3. INSTALL SHIFT SOLENOID VALVE SL2
(a) Install the shift solenoid valve SL2 to the valve body
with the bolt and plate.
Torque: 11 N*m (112 kgf*cm, 8 ft.*lbf)
4. INSTALL SHIFT SOLENOID VALVE DSL
(a) Install the shift solenoid valve DSL to the valve body
with the bolt.
Torque: 11 N*m (112 kgf*cm, 8 ft.*lbf)
5. INSTALL SHIFT SOLENOID VALVE SL1
(a) Install the shift solenoid valve SL1 to the valve body
with the bolt and plate.
Torque: 6.6 N*m (67 kgf*cm, 58 in.*lbf)
C134992
C134991
C134990
C134989

AX–254U140F AUTOMATIC TRANSAXLE – VALVE BODY
AX
6. INSTALL SHIFT SOLENOID VALVE SLT
(a) Install the shift solenoid valve SLT to the valve body
with the bolt and plate.
Torque: 6.6 N*m (67 kgf*cm, 58 in.*lbf)
C134988

AX–290U151F AUTOMATIC TRANSAXLE – DIFFERENTIAL CASE
AX
5. INSTALL FRONT DIFFERENTIAL CASE FRONT
TAPERED ROLLER BEARING
(a) U si ng SST and a pres s, pr es s in the f ron t di fferent ial
case front tapered roller bearing to the differential
case.
SST 09550-60010, 09950-60020 (09951-00680),
09950-70010 (09951-07100, 09951-00890)
NOTICE:
• When replacing the bearing, be sure to
replace it together with the outer race.
• When replacing a bearing of the differential
case, replace both the front and rear bearings
together.
(b) Using SST and a hammer, tap in the front
differential case front tapered roller bearing outer
race to the transaxle housing.
SST 09550-60010, 09950-60020 (09951-00680),
09950-70010 (09951-07100, 09951-00890)
NOTICE:
• When replacing the bearing, be sure to
replace it together with the outer race.
• Clearance is not allowed between the bearing
and transaxle housing.
6. ADJUST DIFFERENTIAL SIDE BEARING PRELOAD
(a) Install the differential assembly to the transaxle
case.
(b) Clean the matching surfaces of the transaxle case
and transaxle housing.
(c) Install the transaxle housing to the transaxle case
and tighten them with the 16 bolts.
Torque: 22 N*m (224 kgf*cm, 16 ft.*lbf) for bolt A
29 N*m (295 kgf*cm, 21 ft.*lbf) for bolt B
29 N*m (295 kgf*cm, 21 ft.*lbf) for bolt C
22 N*m (224 kgf*cm, 16 ft.*lbf) for bolt D
HINT:
• Each bolt length is indicated below.
Bolt length:
50 mm (1.97 in.) for bolt A
50 mm (1.97 in.) for bolt B
42 mm (1.65 in.) for bolt C
72 mm (2.84 in.) for bolt D
• Usually, bolt A is a non-reusable bolt. In this
case, however, it can be used after cleaning it.
C127428E01
D025603E01
C127429
D003568E04

U151F AUTOMATIC TRANSAXLE – DIFFERENTIAL CASEAX–291
AX
(d) Using SST, turn the differential assembly right and
left 2 or 3 times to allow the bearing to settle.
SST 09564-32011
(e) Using SST and a torque wrench, measure the
turning torque of the differential.
SST 09564-32011
Torque: Standard turning torque at 60 rpm
0.20 to 0.69 N*m (2.0 to 7.0 kgf*cm, 1.8
to 6.1 in.*lbf)
HINT:
If the turning torque is not within the specified value,
refer to the table below and select a thrust washer
so that the turning torque is within the specified
value.
Flange thickness
D025604E03
Mark Thickness Mark Thickness
0 2.00 mm (0.0787
in.)J 2.025 mm
(0.07972 in.)
1 2.05 mm (0.0807
in.)K 2.075 mm
(0.08169 in.)
2 2.10 mm (0.0827
in.)L 2.125 mm
(0.08366 in.)
3 2.15 mm (0.0846
in.)M 2.175 mm
(0.08563 in.)
4 2.20 mm (0.0866
in.)N 2.225 mm
(0.08760 in.)
5 2.25 mm (0.0886
in.)P 2.275 mm
(0.08957 in.)
6 2.30 mm (0.0906
in.)Q 2.325 mm
(0.09154 in.)
7 2.35 mm (0.0925
in.)R 2.375 mm
(0.09350 in.)
8 2.40 mm (0.0945
in.)S 2.425 mm
(0.09547 in.)
9 2.45 mm (0.0965
in.)T 2.475 mm
(0.09744 in.)
A 2.50 mm (0.0984
in.)U 2.525 mm
(0.09941 in.)
B 2.55 mm (0.1004
in.)V 2.575 mm
(0.10138 in.)
C 2.60 mm (0.1024
in.)W 2.625 mm
(0.10335 in.)
D 2.65 mm (1.1043
in.)X 2.675 mm
(0.10531 in.)
E 2.70 mm (0.1063
in.)Y 2.725 mm
(0.10728 in.)
F 2.75 mm (0.1083
in.)AA 2.775 mm
(0.10925 in.)
G 2.80 mm (0.1102
in.)AB 2.825 mm
(0.11122 in.)
H 2.85 mm (0.1122
in.)--

AX–292U151F AUTOMATIC TRANSAXLE – DIFFERENTIAL CASE
AX
(f) Remove the 16 bolts and the transaxle housing.
(g) Remove the differential assembly.
7. INSTALL FRONT DIFFERENTIAL RING GEAR
(a) Using ATF and a heater, heat the front differential
ring gear to 90 to 110
C (194.0 to 230.0F).
NOTICE:
Do not overheat the ring gear to 110
C (230.0F)
or more.
(b) Clean the contract surface of the front differential
case.
(c) Align the matchmarks, and install the front
differential ring gear case quickly.
NOTICE:
• Check the position and number of the
grooves on each end face of the differential
ring gear.
• Do not install the bolts while the ring gear is
hot.
(d) Tighten the 14 bolts.
Torque: 95 N*m (969 kgf*cm, 70 ft.*lbf)
NOTICE:
Tighten the bolts a little at a time in diagonal
order.
C050259E02
C127429
D025215E03
C140285E01
C127422