stop start TOYOTA RAV4 PLUG-IN HYBRID 2022 Owner's Guide

2044-2. Opening, closing and locking the doors
The setting changes each time an oper-
ation is performed, as shown below.
(When changing the setting continu-
ously, release the buttons, wait for at
least 5 seconds, and repeat step 3.)
Vehicles with alarm: To prevent unin-
tended triggering of the alarm, unlock
the doors using the wireless remote
control and open and close a door once
after the settings have been changed. (If
a door is not opened within 30 seconds
after is pressed, the doors will
be locked again and the alarm will auto-
matically be set.)
In a case that the alarm is triggered,
immediately stop the alarm. (P.78)
QImpact detection door lock release
system
In the event that the vehicle is subject to
a strong impact, all the doors are
unlocked. Depending on the force of the
impact or the type of accident, however,
the system may not operate.
QOperation signals
Doors: The emergency flashers flash to
indicate that the doors have been
locked/unlocked. (Locked: Once;
Unlocked: Twice)
Side windows and panoramic moon roof
(if equipped): A buzzer sounds to indi-
cate that the side windows and pan-
oramic moon roof are operating.
QSecurity feature
If a door is not opened within approxi-
mately 30 seconds after the vehicle is
unlocked, the security feature automati-
cally locks the vehicle again. (However,
depending on the location of the elec-
tronic key, the key may be detected as
being in the vehicle. In this case, vehicle
may be unlocked.)
QWhen the door cannot be locked by
the lock sensor on the upper part of
the door handle
If the door will not lock even when the
topside sensor area is touched, try
touching both the topside and underside
sensor areas at the same time.
When gloves are being worn, remove
the gloves.
QDoor lock buzzer
A buzzer sounds continuously for 5 sec-
onds in the following situations. Fully
close all the doors and lock the vehicle
once more.
OIf an attempt to lock the doors using
the smart entry & start system is made
when a door other than the door you
are locking is open.
OIf an attempt to lock the doors using
the wireless remote control is made
when a door is open.
Multi-information
display/BeepUnlocking function
(Left-hand drive
vehicles)
(Right-hand drive
vehicles)
Exterior: Beeps 3
times
Holding the driver’s
door handle
unlocks only the
driver’s door.
Holding the front
passenger’s door
handle or pressing
the back door
opener switch
unlocks all the
doors.
Exterior: Beeps
twice
Holding either front
door handle or
pressing the back
door opener switch
unlocks all the
doors.

213
4 4-2. Opening, closing and locking the doors
Before driving
enables automatic opening and
closing of the power back door by
putting your foot near the lower
center part of the rear bumper and
moving it away from the rear
bumper. When operating the Hands
Free Power Back Door, make sure
that the power switch is in OFF, the
Hands Free Power Back Door
operation is enabled (P.184) and
you are carrying an electronic key.
1While carrying an electronic key,
stand within the smart entry &
start system operation range,
approximately 30 to 50 cm (11.8
to 19.7 in.) from the rear
bumper.
Kick sensor
Hands Free Power Back Door
operation detection area
Smart entry & start system oper-
ation detection area (P.221)
2Perform a kick operation by
moving your foot to within
approximately 10 cm (3.9 in.) of
the rear bumper and then pulling
it back.
Perform the entire kick operation within
1 second.The back door will not start operating
while a foot is detected under the rear
bumper.
Operate the Hands Free Power Back
Door without contacting the rear
bumper with your foot.
If another electronic key is in the cabin
or luggage compartment, it may take
slightly longer than normal for the oper-
ation to occur.
Kick sensor
Hands Free Power Back Door
operation detection area
3When the kick sensor detects
that your foot is pulled back, a
buzzer will sound and the back
door will automatically fully
open/close.
If a foot is moved under the rear
bumper while the back door is open-
ing/closing, the back door will stop
moving.
If a foot is moved under the rear
bumper again during the halted opera-
tion, the back door will perform the
reverse operation.
QLuggage compartment light
OThe luggage compartment light turns
on when the back door is opened.
OWhen the power switch is turned to
OFF, the light will go off automatically
after 20 minutes.
A
B
C
A
B

2144-2. Opening, closing and locking the doors
QBack door closer
In the event that the back door is left
slightly open, the back door closer will
automatically close it to the fully closed
position.
Whatever the state of the power switch,
the back door closer operates.
QPower back door operating condi-
tions
The power back door can automatically
open and close under the following con-
ditions:
OWhen the power back door system is
enabled. (P.184)
OWhen the back door is unlocked.
However, if the back door opener switch
is pressed and held while carrying the
electronic key on your person, the
power back door will be operated even if
the back door is locked. (P.212)
OWhen the power switch is in ON, in
addition to the above for the opening
operations, the back door operates for
any of the following conditions:
• Parking brake is engaged
• The brake pedal is depressed
• The shift lever is in P.
QOperation of the power back door
OA buzzer sounds to indicate that the
back door is opening/closing.
OWhen the power back door system is
disabled, the power back door does
not operate but it can be opened and
closed by hand.
OWhen the power back door automati-
cally opens, if an abnormality due to
people or objects is detected, opera-
tion will stop.
QJam protection function
Sensors are equipped on both sides of
the power back door. If anything
obstructs the power back door while it is
closing, the back door will automatically
operate in the opposite direction or stop.
QFall-down protection function
While the power back door is opening
automatically, applying excessive force
to it will stop the opening operation to
prevent the power back door from sud-
denly shutting.
QBack door closing assist
If the back door is lowered manually
when the back door is stopped at an
open position, the back door will fully
close automatically.
QBack door reserve lock function
This function is a function which
reserves locking of all doors, before-
hand, when the power back door is
open.
When the following procedure is per-
formed, all the doors except the power
back door are locked and then power
back door will also be locked at the
same time it is closed.
1Close all doors, except the back
door.
2During the power back door closing
operation, lock the doors using the
smart entry & start system from the
front doors (P.203) or the wireless
remote control. (P.203)
Operation signals will indicate that all
the doors have been closed and locked.
(P.204)
OIf the electronic key is placed inside
the vehicle after starting a close oper-
ation via the door reserve lock func-
tion, the electronic key may become
locked inside the vehicle.
OIf the power back door does not fully
close due to the operation of the jam
protection function, etc., while the
back door is automatically closing

217
4
4-2. Opening, closing and locking the doors
Before driving
WARNING
QBack door closer
OIn the event that the back door is
left slightly open, the back door closer will automatically close it to the fully closed position. It takes
several seconds before the back door closer begins to operate. Be careful not to catch fingers or any-
thing else in the back door, as this may cause bone fractures or other serious injuries.
OUse caution when using the back door closer as it still operates when
the power back door system is can- celed.
QPower back door
Observe the following precautions when operating the power back door.
Failure to do so may cause death or serious injury.
OCheck the safety of the surrounding
area to make sure there are no obstacles or anything that could cause any of your belongings to get
caught.
OIf anyone is in the vicinity, make
sure they are safe and let them know that the back door is about to open or close.
OIf the power back door system is turned off while the back door is
operating automatically, the auto- matic operation is stopped. The back door then has to be operated
manually. Take extra care when on an incline, as the back door may open or close unexpectedly.
OIf the operating conditions of the power back door are no longer met, a buzzer may sound and the back
door may stop opening or closing. The back door then has to be oper-ated manually. Take extra care
when on an incline, as the back door may open or close abruptly.
OOn an incline, the back door may suddenly shut after it opens. Make sure the back door is fully open and
secure.
OIn the following situations, the
power back door may detect an abnormality and automatic opera-tion may be stopped. In this case,
the back door has to be operated manually. Take extra care when on an incline, as the back door may
open or close abruptly.
• When the back door contacts an obstacle
• When the 12-volt battery voltage suddenly drops, such as when the power switch is turned to ON or the
hybrid system is started during automatic operation
OIf a bicycle carrier or similar heavy object is attached to the back door, the power back door may not oper-
ate, causing itself to malfunction, or the back door may suddenly shut again after being opened, causing
someone’s hands, head or neck to be caught and injured. When installing an accessory part to the
back door, using a genuine Toyota part is recommended.
QJam protection function
Observe the following precautions. Failure to do so may cause death or
serious injury.
ONever use any part of your body to intentionally activate the jam pro-
tection function.

2224-2. Opening, closing and locking the doors
OWhen an exterior alarm sounds once
for 5 seconds
OWhen an interior alarm pings continu- ously
QBattery-saving function
The battery-saving function will be acti-
vated in order to prevent the electronic key battery and the 12-volt battery from being discharged while the vehicle is not
in operation for a long time.
OIn the following situations, the smart
entry & start system may take some time to unlock the doors.• The electronic key has been left in an
area of approximately 3.5 m (11.5 ft.) of the outside of the vehicle for 2 min-utes or longer.
• The smart entry & start system has not been used for 5 days or longer.
OIf the smart entry & start system has not been used for 14 days or longer, the doors cannot be unlocked at any
doors except the driver’s door. In this case, take hold of the driver’s door handle, or use the wireless remote
control or the mechanical key, to unlock the doors.
QTurning an electronic key to bat-
tery-saving mode
OWhen battery-saving mode is set, bat-
tery depletion is minimized by stop- ping the electronic key from receiving radio waves.
Press twice while pressing and
holding .
Confirm that the electronic key indicator
flashes 4 times.
While the battery-saving mode is set,
the smart entry & start system cannot be
used. To cancel the function, press any
of the electronic key buttons.
OElectronic keys that will not be used for long periods of time can be set to
the battery-saving mode in advance.
QWhen electronic key function stops
If the position of the electronic key has
not changed for a certain amount of time such as when the electronic key is left somewhere, the function of the elec-
tronic key stops to reduce depletion of the battery.In this case, function can automatically
be restored by moving the position of the key such as by lifting it up.
QConditions affecting operation
The smart entry & start system uses
weak radio waves. In the following situa- tions, the communication between the electronic key and the vehicle may be
affected, preventing the smart entry & start system, wireless remote control and immobilizer system from operating
properly.
OWhen the electronic key battery is
depleted
SituationCorrection proce-
dure
An attempt was
made to lock the
vehicle while a
door was open.
Close all of the
doors and lock the
doors again.
SituationCorrection proce-
dure
The power switch
was turned to ACC
while the driver’s
door was open (or
the driver’s door
was opened while
the power switch
was in ACC).
Turn the power
switch to OFF and
close the driver’s
door.

2244-2. Opening, closing and locking the doors
unlocked by the entry function. (Use
the wireless remote control to unlock
the doors.)
OTouching the door lock sensor while
wearing gloves may delay or prevent
lock operation. Remove the gloves
and touch the lock sensor again.
OWhen the lock operation is performed
using the lock sensor, recognition sig-
nals will be shown up to two consecu-
tive times. After this, no recognition
signals will be given.
OIf the door handle becomes wet while
the electronic key is within the effec-
tive range, the door may lock and
unlock repeatedly. In that case, follow
the following correction procedures to
wash the vehicle:
• Place the electronic key in a location 2
m (6 ft.) or more away from the vehi-
cle. (Take care to ensure that the key
is not stolen.)
• Set the electronic key to battery-sav-
ing mode to disable the smart entry &
start system. (P.222)
OIf the electronic key is inside the vehi-
cle and a door handle becomes wet
during a car wash, a message may be
shown on the multi-information dis-
play and a buzzer will sound outside
the vehicle. To turn off the alarm, lock
all the doors.
OThe lock sensor may not work prop-
erly if it comes into contact with ice,
snow, mud, etc. Clean the lock sensor
and attempt to operate it again, or use
the lock sensor on the lower part of
the door handle.
OA sudden approach to the effective
range or door handle may prevent the
doors from being unlocked. In this
case, return the door handle to the
original position and check that the
doors unlock before pulling the door
handle again.
OIf there is another electronic key in the
detection area, it may take slightly lon-
ger to unlock the doors after the door
handle is gripped.
QWhen the vehicle is not driven for
extended periods
OTo prevent theft of the vehicle, do not
leave the electronic key within 2 m (6
ft.) of the vehicle.
OThe smart entry & start system can be
deactivated in advance. (P.573)
OBattery-saving mode can reduce the
power consumption of electronic keys.
(P.222)
QTo operate the system properly
Make sure to carry the electronic key
when operating the system. For vehicles
with entry function, do not get the elec-
tronic key too close to the vehicle when
operating the system from the outside of
the vehicle.
Depending on the position and holding
condition of the electronic key, the key
may not be detected correctly and the
system may not operate properly. (The
alarm may go off accidentally, or the
door lock prevention may not operate.)
QIf the smart entry & start system
does not operate properly
OLocking and unlocking the doors: Use
the mechanical key. (P.545)
OStarting the hybrid system: P.273
QCustomization
Settings (e.g. smart entry & start sys-
tem) can be changed.
(Customizable features: P.573)
If the smart entry & start system has
been deactivated in a customized set-
ting, refer to the explanations for the fol-
lowing operations.
OLocking and unlocking the doors:
Use the wireless remote control or
mechanical key. (P.203, 545)
OStarting the hybrid system and chang-
ing power switch modes: P.545
OStopping the hybrid system: P.275

2565-1. Before driving
5- 1. B ef ore dr iv in g
QBefore starting the hybrid sys-
tem
Check that the AC charging cable is
disconnected. (P.134)
QStarting the hybrid system
P.273
QDriving
1With the brake pedal depressed,
shift the shift lever to D.
(P.277)
2Release the parking brake.
(P.282)
If the parking brake is in automatic
mode, the parking brake is released
automatically when shifting the shift
lever to any position other than P.
(P.283)
3Gradually release the brake
pedal and gently depress the
accelerator pedal to accelerate
the vehicle.
QStopping
1With the shift lever in D, depress
the brake pedal.
2If necessary, set the parking
brake. (P.282)
If the vehicle is to be stopped for an
extended period of time, shift the shift
lever to P. (P.277)
QParking the vehicle
1With the shift lever in D, depress
the brake pedal.
2Set the parking brake (P.282),
and shift the shift lever to P.
(P.277)
3Turn the power switch to OFF to
stop the hybrid system.
4Lock the door, making sure that
you have the key on your per-
son.
If parking on a hill, block the wheels as
needed.
QStarting off on a steep uphill
1With the brake pedal depressed,
shift the shift lever to D.
(P.277)
2Pull the parking brake switch to
set the parking brake manually.
(P.282)
3Release the brake pedal and
gently depress the accelerator
pedal to accelerate the vehicle.
Parking brake automatic release func-
tion (P.283)
QWhen starting off on a uphill
The hill-start assist control will activate.
(P.392)
QFor electricity-saving and fuel-effi-
cient driving
Understand the system characteristics
of the vehicle to use the functions of the
hybrid system. Also, keep in mind that
Plug in Hybrid Electric Vehicles are sim-
ilar to conventional vehicles, and it is
necessary to refrain from activities such
as sudden acceleration. Refer to “Plug
in Hybrid Electric Vehicle driving tips”
(P.99).
Driving the vehicle
The following procedures
should be observed to ensure
safe driving:
Driving procedure

257
5
5-1. Before driving
Driving
QDriving in the rain
ODrive carefully when it is raining, because visibility will be reduced, the
windows may become fogged-up, and the road could be slippery.
ODrive carefully when it starts to rain, as the road surface could be espe-cially slippery.
ORefrain from high speeds when driv-ing on an expressway in the rain,
because there may be a layer of water between the tires and the road sur-face, preventing the steering and
brakes from operating properly.
QECO Accelerator Guidance ( P.180)
It is easier to drive in an Eco-friendly
manner by driving while referring to the ECO Accelerator Guidance display. Also, by using the ECO Accelerator
Guidance it is easier to increase the “Eco Score” evaluation.
OWhen starting off: While staying within the ECO Accelerator Guidance range, gradually depress the accelerator
pedal and accelerate to the desired speed. If excessive acceleration is avoided, the “Start” score will
increase.
OWhen driving: After accelerating to the
desired speed, release the accelera- tor pedal and drive at a stable speed within the ECO Accelerator Guidance
range. By keeping the vehicle within the ECO Accelerator Guidance range, the “Cruise” score will increase.
OWhen stopping: When stopping the vehicle, early releasing the accelera-
tor pedal will cause the “Stop” score to increase.
QRestraining the hybrid system out-put (Brake Override System)
OWhen the accelerator and brake ped-als are depressed at the same time,
the hybrid system output may be restrained.
OA warning message is displayed on the multi-information display and
head-up display (if equipped) while
the system is operating.
QBreaking in your new Toyota
To extend the life of the vehicle, observ- ing the following precautions is recom-
mended:
OFor the first 300 km (200 miles):
Avoid sudden stops.
OFor the first 800 km (500 miles):
Do not tow a trailer.
OFor the first 1000 km (600 miles):
• Do not drive at extremely high speeds.• Avoid sudden acceleration.
• Do not drive continuously in low gears.• Do not drive at a constant speed for
extended periods.
QOperating your vehicle in a foreign country
Comply with the relevant vehicle regis-
tration laws and confirm the availability of the correct fuel. ( P.560)
WARNING
Observe the following precautions.
Failure to do so may result in death or serious injury.
QWhen starting the vehicle
Always keep your foot on the brake pedal while stopped with the
“READY” indicator is illuminated. This prevents the vehicle from creeping.

2605-1. Before driving
WARNING
OAvoid revving or racing the engine. Running the engine at high speed
while the vehicle is stopped may cause the exhaust system to over-heat, which could result in a fire if
combustible material is nearby.
QWhen the vehicle is parked
ODo not leave glasses, cigarette lighters, spray cans, or soft drink cans in the vehicle when it is in the
sun. Doing so may result in the follow-ing:
• Gas may leak from a cigarette lighter or spray can, and may lead to a fire.
• The temperature inside the vehicle may cause the plastic lenses and plastic material of glasses to
deform or crack.
• Soft drink cans may fracture, caus- ing the contents to spray over the
interior of the vehicle, and may also cause a short circuit in the vehicle’s electrical components.
ODo not leave cigarette lighters in the vehicle. If a cigarette lighter is in a
place such as the glove box or on the floor, it may be lit accidentally when luggage is loaded or the seat
is adjusted, causing a fire.
ODo not attach adhesive discs to the
windshield or windows. Do not place containers such as air fresh-eners on the instrument panel or
dashboard. Adhesive discs or con- tainers may act as lenses, causing a fire in the vehicle.
ODo not leave a door or window open if the curved glass is coated
with a metallized film such as a sil- ver-colored one. Reflected sunlight may cause the glass to act as a
lens, causing a fire.
OAlways apply the parking brake, shift the shift lever to P, stop the hybrid system and lock the vehicle.
Do not leave the vehicle unat- tended while the “READY” indicator is illuminated.
If the vehicle is parked with the shift lever in P but the parking brake is not set, the vehicle may start to
move, possibly leading to an acci- dent.
ODo not touch the exhaust pipes while the “READY” indicator is illu-minated or immediately after turn-
ing the hybrid system off. Doing so may cause burns.
QWhen taking a nap in the vehicle
Always turn the hybrid system off. Otherwise, if you accidentally move
the shift lever or depress the acceler- ator pedal, this could cause an acci-dent or fire due to hybrid system
overheating. Additionally, if the vehi- cle is parked in a poorly ventilated area, exhaust gases may collect and
enter the vehicle, leading to death or a serious health hazard.
QWhen braking
OWhen the brakes are wet, drive more cautiously.
Braking distance increases when the brakes are wet, and this may cause one side of the vehicle to
brake differently than the other side. Also, the parking brake may not securely hold the vehicle.
OIf the electronically controlled brake system does not operate, do not fol-
low other vehicles closely and avoid hills or sharp turns that require braking.
In this case, braking is still possible, but the brake pedal should be depressed more firmly than usual.
Also, the braking distance will increase. Have your brakes fixed immediately.

263
5
5-1. Before driving
Driving
WARNING
ODo not place cargo or luggage in or on the following locations.
• At the feet of the driver
• On the front passenger or rear seats (when stacking items)
• On the luggage cover (if equipped)
• On the instrument panel
• On the dashboard
OSecure all items in the occupant compartment.
QLoad and distribution
ODo not overload your vehicle.
ODo not apply loads unevenly.
Improper loading may cause deterio-
ration of steering or braking control which may cause death or serious injury.
QWhen loading cargo on the roof luggage carrier (if equipped)
Observe the following precautions:
OPlace the cargo so that its weight is distributed evenly between the front
and rear axles.
OIf loading long or wide cargo, never
exceed the vehicle overall length or width. ( P.558)
OBefore driving, make sure the cargo is securely fastened on the roof lug-gage carrier.
OLoading cargo on the roof luggage carrier will make the center of grav-
ity of the vehicle higher. Avoid high speeds, sudden starts, sharp turns, sudden braking or abrupt maneu-
vers, otherwise it may result in loss of control or vehicle rollover due to failure to operate this vehicle cor-
rectly and result in death or serious injury.
OIf driving for a long distance, on rough roads, or at high speeds, stop the vehicle now and then
during the trip to make sure the cargo remains in its place.
ODo not exceed 80 kg (176.4 lb.) cargo weight on the roof luggage carrier.
NOTICE
QWhen loading cargo on the roof luggage carrier (if equipped)
Be careful not to scratch the surface
of the panoramic moon roof (if equipped).