odometer YAMAHA XSR 900 2022 Owners Manual

Instrument and control functions
4-10
1
2
345
6
7
8
9
10
11
12
13
speed, as measured by the rotational
velocity of the crankshaft, in revolutions
per minute (r/min).
NOTICE
ECA10032
Do not operate the engine in the ta-
chometer red zone.Red zone: 10600 r/min and above
Vehicle information displays
The two vehicle information displays
can be individually set to show the fol-
lowing items:
ODO: odometer

F-TRIP: fuel reserve tripmeter

TRIP1: tripmeter

TRIP2: tripmeter

F.AVE: average fuel economy

F.CRNT: instantaneous fuel econ-
omy

A.TEMP: air temperature

C.TEMP: coolant temperature

Fuel meter

FUEL CON: amount of fuel con-
sumed

TRIP TIME: running time
Operate the vehicle information display
as follows:
Rotate the wheel switch to move the
cursor over a display.
Press the wheel switch inward and the
selected display will highlight grey.
Rotate the wheel switch to choose a dif-
ferent display item.
Press the wheel switch inward to con-
firm the new display item.
TIP
In LAP TIME mode, the vehicle in-
formation display is replaced by
the lap information.

TRIP1, TRIP2, F-TRIP, F.AVE,
FUEL CON and TRIP TIME itemscan be individually reset. Odometer:
The odometer shows the total distance
traveled by the vehicle.TIPODO will lock at 999999 and cannot bereset.
Fuel reserve tripmeter:When the fuel tank reserve level has
been reached, F-TRIP appears auto-
matically and begins recording dis-
tance traveled from that point.
After refueling and traveling some dis-
tance, F-TRIP will automatically disap-
pear.
Tripmeters:
1. Vehicle information displays
1
BEA-28199-E0.book 10 ページ ２０２１年１２月１日　水曜日　午後７時８分

Instrument and control functions
4-19
1
2
34
5
6
7
8
9
10
11
12
13 “Clock”
This module allows you to set the clock.
When the clock module is selected, the
hours will be highlighted.
Set the hours by rotating the wheel
switch. Press the wheel switch inward
to confirm and highlight the minutes.
After confirming the minutes, you will
be returned to the top MENU screen.
“All Reset”
This module resets all settings items
(except the odometer and clock) to their
default or factory presets.
Select YES to reset all items. After se-
lecting YES, all items will be reset and
the screen will automatically return to
the top MENU screen.
EAU12823
Clutch leverTo disengage the drivetrain from the
engine, such as when shifting gears,
pull the clutch lever toward to the han-
dlebar. Release the lever to engage the
clutch and transmit power to the rear
wheel.TIPThe lever should be pulled rapidly and
released slowly for smooth shifting.(See page 6-3.)
km/h
Clock
0010
NOYES
km/h
All Reset
1. Clutch lever
RE
SSET
M
ODE
1 1 1
BEA-28199-E0.book 19 ページ ２０２１年１２月１日　水曜日　午後７時８分

Periodic maintenance and adjustment
7-3
1
2
3
4
5
67
8
9
10
11
12
13
EAU71033
Periodic maintenance chartsTIP
Items marked with an asterisk should be performed by your Yamaha dealer because these items require special tools,
data, and technical skills.

From 50000 km (30000 mi), repeat the maintenance intervals starting from 10000 km (6000 mi).

The annual checks must be performed every year, except if a distance-based maintenance is performed in-stead.
EAU71051
Periodic maintenance chart for the emission control systemNO. ITEM CHECK OR MAINTENANCE JOB ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 10000 km
(6000 mi) 20000 km
(12000 mi) 30000 km
(18000 mi) 40000 km
(24000 mi)
1 *Fuel line Check fuel hoses for cracks or
damage.
Replace if necessary. 
2 *Spark plugs Check condition.
Adjust gap and clean.


3 *Valve clearance Check and adjust. Every 40000 km (24000 mi)
4 *Fuel injection Check engine idle speed.

Check and adjust synchronization. 
5 *Exhaust system Check for leakage.
Tighten if necessary.
Replace gaskets if necessary. 
6 *Evaporative
emission control
system Check control system for damage.
Replace if necessary.

BEA-28199-E0.book 3 ページ ２０２１年１２月１日　水曜日　午後７時８分

Periodic maintenance and adjustment
7-4
1
2
3
4
5
678
9
10
11
12
13
EAU71353
General maintenance an d lubrication chartNO. ITEM CHECK OR MAINTENANCE JOB ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 10000 km
(6000 mi) 20000 km
(12000 mi) 30000 km
(18000 mi) 40000 km
(24000 mi)
1 *Diagnostic system
check Perform dynamic inspection using
Yamaha diagnostic tool.
Check the error codes. 
2 *Air filter element Replace. Every 40000 km (24000 mi)
3Clutch Check operation.
Adjust. 
4 *Front brake Check operation, fluid level, and
for fluid leakage.
Replace brake pads if necessary. 
5 *Rear brake Check operation, fluid level, and
for fluid leakage.
Replace brake pads if necessary. 
6 *Brake hoses Check for cracks or damage.

Replace. Every 4 years
7 *Brake fluid Change. Every 2 years
8 *Wheels Check runout and for damage.
Replace if necessary. 
9 *Tires Check tread depth and for
damage.
Replace if necessary.
Check air pressure.
Correct if necessary. 
10 *Wheel bearings Check bearing for looseness or
damage. 
11 *Swingarm pivot
bearings Check operation and for
excessive play. 
Lubricate with lithium-soap-based grease. Every 50000 km (30000 mi)
BEA-28199-E0.book 4 ページ ２０２１年１２月１日　水曜日　午後７時８分

Periodic maintenance and adjustment
7-5
1
2
3
4
5
67
8
9
10
11
12
13
12 Drive chain Check chain slack, alignment and
condition.
Adjust and lubricate chain with a special O-ring chain lubricant
thoroughly. Every 1000 km (600 mi) and after washing the motorcycle, riding in the rain or
riding in wet areas
13 *Steering bearings Check bearing assemblies for
looseness. 

Moderately repack with lithium-soap-based grease. 
14 *Chassis fasteners Make sure that all nuts, bolts and
screws are properly tightened. 
15 *Brake lever pivot
shaft Lubricate with silicone grease.

16 Brake pedal pivot
shaft Lubricate with lithium-soap-based
grease. 
17 Clutch lever pivot
shaft Lubricate with lithium-soap-based
grease. 
18 Shift pedal pivot
shaft Lubricate with lithium-soap-based
grease. 
19 Sidestand Check operation.
Lubricate with molybdenum
disulfide grease. 
20 *Sidestand switch Check operation and replace if
necessary. 
21 *Front fork Check operation and for oil
leakage.
Replace if necessary. 
22 *Shock absorber
assembly Check operation and for oil
leakage.
Replace if necessary. 
NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 10000 km
(6000 mi) 20000 km
(12000 mi) 30000 km
(18000 mi) 40000 km
(24000 mi)BEA-28199-E0.book 5 ページ ２０２１年１２月１日　水曜日　午後７時８分

Periodic maintenance and adjustment
7-6
1
2
3
4
5
678
9
10
11
12
13
23 *Rear suspension
relay arm and
connecting arm
pivoting points Check operation.

24 *Engine oil Change (warm engine before
draining).
Check oil level and vehicle for oil leakage. 
25 *Engine oil filter
cartridge Replace.

26 *Cooling system Check coolant level and vehicle
for coolant leakage. 
Change. Every 3 years
27 *Front and rear brake
switches Check operation.

28 *Moving parts and
cables Lubricate.

29 *Throttle grip Check operation.
Lubricate throttle grip housing
tube guides. 
30 *Lights, signals and
switches Check operation.
Adjust headlight beam.

NO. ITEM CHECK OR MAINTENANCE JOB
ODOMETER READING
ANNUAL
CHECK
1000 km
(600 mi) 10000 km
(6000 mi) 20000 km
(12000 mi) 30000 km
(18000 mi) 40000 km
(24000 mi)
BEA-28199-E0.book 6 ページ ２０２１年１２月１日　水曜日　午後７時８分