ACURA NSX 1991 Service Repair Manual

Page 141 of 1640

Piston Ring s
Ring-to-Groov e Clearance s
After installin g a ne w se t o f rings , measur e ring-to-groov e
clearances:
Top an d Secon d Rin g Clearanc e
Standar d (New) :
0.030-0.05 5 mm
(0.00 1 - 0.00 2 in )
Servic e Limit : 0.1 3 m m (0.00 5 in )
FEELE R GAUG E
Alignmen t
1. Instal l th e ring s a s show n o n pag e 7- 15.
Identif y to p an d secon d ring s b y th e chamfe r o n th e
edge , an d mak e sur e the y ar e i n th e prope r groove s
i n th e piston .
NOTE : Th e manufacturin g mark s mus t b e facin g
upward .
2. Rotat e th e ring s i n thei r groove s t o mak e sur e the y
do no t bind .
MAR K
TO P RIN G
SECON D RIN G
OI L RIN G MAR
K
- SPACE R
3. Positio n th e rin g en d gap s a s shown :
SECON D RIN G CA PDO NO T positio n an y rin g ga pat pisto n thrus t surfaces .
TOP RIN G GA P
DO NO T positio n an y rin g ga pin lin e wit h pisto n pi n hole .OIL RIN G GA P
SPACE
R GA P
OI
L RIN G
GAP
ProCarManuals.com

Page 142 of 1640

Piston/Connecting Ro d Assemblie s
Installation
Before installin g th e piston , appl y a coa t o f
engin e oi l t o th e rin g groove s an d cylinde r
bores.
1. I f th e crankshaf t i s alread y installed :
• Guid e th e pisto n carefull y t o preven t damage .
• Fi t lon g rubbe r hose s (abou t 3 0 c m (1 2 in ) long ) t o
th e connectin g ro d bolt s t o protec t th e crankshaft .
• Instal l th e piston s afte r settin g th e crankshaf t t o
BD C fo r eac h cylinder .
CORREC TINCORREC T
RUBBER HOSE S
Install th e pisto n assemblie s i n No . 1 an d No . 4
cylinders , No . 2 an d No . 5 cylinders , an d No . 3
an d No . 6 cylinders .
Instal l th e rin g compressor , chec k tha t th e bear -
in g i s securel y i n place ; the n positio n th e pisto n
i n th e cylinde r an d ta p i t i n usin g th e woode n
handl e of a hammer .
Sto p afte r th e rin g compresso r pop s fre e an d
chec k th e connectin g rod-to-cran k journa l align -
ment befor e puttin g ro d int o place .
Install th e ro d cap s wit h bearings , an d torqu e th e
nut s t o 2 0 N- m (2. 0 kg-m , 1 4 Ib-ft) , the n tur n th e
nu t 9 5 degree s (se e pag e 7-19 ).
If th e crankshaf t i s no t installed :
• Remov e th e ro d cap s an d bearings , instal l th e
ring compressor , the n positio n th e pisto n in th e
cylinde r an d ta p it i n usin g th e woode n handl e of
a hammer .
The arro w mus t fac ethe timin g bel t sid eof th e engin e an d th econnectin g ro d oi l hol emus t fac e th e rea r sid eof th e engine .
CONNECTIN G RO DOIL HOL E
NOTE : Maintai n downwar d forc e o n th e rin g com -
presso r t o preven t ring s fro m expandin g befor e
enterin g th e cylinde r bore .
Use th e woode n handl eof a hamme r t o push , o rtap th e pisto n int o th ecylinde r bore .
RING COMPRESSO R
ProCarManuals.com

Page 143 of 1640


Crankshaft

Installation

Before installing the crankshaft, apply a coat of

engine oil to the main bearings and rod

bearings.

1. Insert bearing halves in the engine block and con-

necting rods.

2. Lower the crankshaft into the block.

3. Install the thrust washers on the No. 3 journal. Oil

thrust washer surfaces.

4. Install the bearings and caps. Tighten 9 x 1.25 mm

cap bolts to the specified torque.ProCarManuals.com

Page 144 of 1640

NOTE:
• Guid e th e pisto n carefull y t o preven t damage .
• Fi t lon g rubbe r hose s (abou t 3 0 c m long ) t o con -
nectin g ro d bolt s t o protec t th e crankshaft .
• Instal l th e piston s afte r settin g th e crankshaf t t o
BD C fo r eac h cylinder .
CORREC TINCORREC T
RUBBER HOSE S
9 x 0.7 5 mm20 N- m (2. 0 kg-m , 1 4 Ib-ft )
afte r tur n t o 95 °
MAR K
• Lin e u p th e mark s whe n installin g connectin g
rod cap .
5. Chec k th e ro d bearin g clearanc e wit h plastigag e
(se e pag e 7-7 ), the n torqu e th e connectin g ro d ca p
nuts .
NOTE : Referenc e number s o n connectin g rod s ar e
fo r big-en d bor e toleranc e an d d o NO T indicat e th e
positio n o f pisto n i n engine .
CONNECTIN G RO D CA P NU T TORQUIN G
METHOD
1) Torqu e th e connectin g ro d ca p nu t t o 2 0 N- m
(2. 0 kg-m , 1 4 Ib-ft ) wit h a beam-typ e torqu e
wrench .
2 ) Instal l a torqu e angl e gaug e t o th e ca p nut , the n
tur n th e ca p nu t 9 5 degrees .
Snap-onTA360 o requivalen t
BEARIN
G CA P
WASHERS
ProCarManuals.com

Page 145 of 1640

Crankshaft
Installation
6. Instal l th e bearin g ca p bridge , an d tighte n 1 1 x 1. 5
m m bolt s t o th e specifie d torqu e diagonall y out -
war d fro m th e center .
Torqu e 6 6 N- m (6. 6 kg-m , 4 8 Ib-ft )
7 . Tighte n ca p sid e bolt s (1 0 x 1.2 5 mm ) t o th e
specifie d torque .
Torque : 5 0 N- m (5. 0 kg-m , 3 6 Ib-ft )
• Coa t th e bol t threa d an d sea t surfac e wit h
engin e oil .
NOTE : Th e shorte r sid e bolt s ar e fo r th e fron t side .
BEARIN G CA PBRIDG ECAP BRIDG E BOL T11 x 1. 5 m m66 N- m (6. 6 kg-m ,48 Ib-ft )
SID E BOL T
10 x 1.2 5 mm50 N- m (5. 0 kg-m ,36 Ib-ft ) CA
P BOL T9 x 1.2 5 mm40 N- m (4. 0 kg-m ,29 Ib-ft )
8. Appl y liqui d gaske t t o th e bloc k matin g surfac e o f
the lef t sid e cove r an d oi l pum p case , an d instal l
them o n th e engin e block .
NOTE : Th e sea l surfac e o n th e bloc k shoul d b e
dry . Appl y a ligh t coa t o f oi l t o th e crankshaf t an d
to th e li p o f seal .
LEF T SIDE :
Apply liqui dgaske t t o bloc kmatin g surface .
LEFT SID E COVE R
SPECIA L BOLT S
6 x 1. 0 m m12 N- m (1. 2 kg-m ,9 Ib-ft )
Replace . DOWE
L PI N
BEARIN G CA P BOLT S TORQU E SEQUENC E
ProCarManuals.com

Page 146 of 1640

6 x 1. 0 m m12 N- m (1. 2 kg-m ,9 Ib-ft )
OIL PUM P
Appl y liqui d
gaske t t o bloc kmatin g surfaces .
SPECIAL BOLT S6 x 1. 0 m m12 N- m (1. 2 kg-m ,9 Ib-ft )Replace .
SPECIAL BOLT S8 x 1.2 5 mm22 N- m (2. 2 kg-m ,16 Ib-ft )Replace .
NOTE:
• Use liqui d gasket , Par t No. 08718-0001 .
• Chec k tha t th e matin g surface s ar e clea n an d
dry befor e applyin g liqui d gasket .
• Appl y liqui d gaske t evenly , bein g carefu l t o cove r
al l o f th e matin g surface .
• T o preven t leakag e o f oil , appl y liqui d gaske t t o
th e inne r thread s of the bol t holes .
LEFTSIDE COVE R
Apply liqui d gaske talong th e broke n line .
OIL PUM PApply liqui d gaske talong th e broke n line .
• D o no t instal l th e part s i f fiv e minute s o r mor e
have elapse d sinc e applyin g liqui d gasket .
Instead reappl y liqui d gaske t afte r removin g ol d
residue .
• Afte r assembly , wai t a t leas t 2 0 minute s befor e
filling th e engin e wit h oil .
9. Instal l th e oi l pas s pip e an d joint .
10 . Instal l th e baffl e plate .
11 . Instal l th e oi l screen .
12 . Instal l th e oi l pa n (se e pag e 8-10 ).
CAUTION : Wheneve r an y crankshaf t o r connec -
tin g ro d bearin g i s replaced , afte r reassembly , ru n
th e engin e a t idlin g spee d unti l i t reache s norma l
operatin g temperature , the n continu e t o ru n fo r ap -
proximatel y 1 5 minutes .
OIL PUM P SIDE :
6 x 1. 0 m m12 N- m (1. 2 kg-m , 9 Ib-ft )
OIL SCREE NBAFFLE PLAT E
OIL PAS SPIPE
ProCarManuals.com

Page 147 of 1640

Special Tool s
8-9
8-5
ProCarManuals.com

Page 148 of 1640

Engine Lubricatio n
Illustrated Inde x
FRON T CYLINDE RHEADENGIN E OI L PRESSUR E GAUG ESENDIN G UNI T22 N- m (2. 2 kg-m . 1 6 Ib-ft )
NOTE :
• Us e ne w O-ring s whe n reassembling .
• Appl y oi l t o O-ring s befor e installation .
• Us e liqui d gasket , Par t No . 08718-0001 .
• I f th e botto m o f th e oi l pa n is deformed , i t shoul d b e
repaire d o r th e oi l pa n shoul d b e replace d t o retai n
prope r clearanc e betwee n th e scree n an d th e
bottom .
OIL CONTRO L ORIFIC ERemove wit h 6 m mbol t an d clean .
O-RIN GReplace .
8 x 1.2 5 mm22 N- m (2. 2 kg- m16 Ib-ft )Replace .
ENGINE OI LPRESSUR ESWITCH
OIL FILTE R BAS EIllustrate d Index ,page 8-1 2
OIL PUM PIllustrate d index , pag e 8- 7Inspection , pag e 8 -8Appl y liqui d gaske t t omatin g surfac e o f engin e block .
OIL PA N GASKE T
Replace .
OIL PA N• D o no t defor mthe bottom .Refer t o pag e 8-1 0whe n installing .
OIL FILTE ROne tur n o r22 N- m (2. 2 kg-m ,16 Ib-ft )Replacemen t 8- 5
6 x 1. 0 m m12 N- m(1.2 kg-m , 9 Ib-ft )
6 x 1. 0 m m12 N- m(1.2 kg-m , 9 Ib-ft )
DRAI N PLU G
20 x 1. 5 m m45 N- m (4. 5 kg-m , 3 3 Ib-ft )
6 x 1. 0 m m14 N- m (1. 4 kg-m , 1 0 Ib-ft )
ENGIN E OI LCOOLE R
WATE
R PAS S PIP E
DOWEL PIN S
SPECIA L BOLT S
8 x 1.2 5 mm22 N- m (2. 2 kg-m ,16 Ib-ft ) O-RING S
Replace . Replace .
OI L PAS S
PIPE
SPECIA L BOLT S6 x 1. 0 m m12 N- m(1.2 kg-m , 9 Ib-ft )
Replace .
6 x 1. 0 m m12 N- m (1. 2 kg-m , 9 Ib-ft )
DOWE
L PI N O-RING
S
Replace .
8 x 1.2 5 mm12 N- m (2. 2 kg-m ,16 Ib-ft )
OILSCREE N
WASHE R
Replace .
ProCarManuals.com

Page 149 of 1640


Engine Oil

Inspection

1. Check engine oil with the engine off and the car

parked on level ground.

2. Make certain that the oil level indicated on the

dipstick is between the upper and lower marks.

3. If the level has dropped close to the lower mark,

add oil until it reaches the upper mark.

CAUTION: Insert the dipstick carefully to avoid

bending it.ProCarManuals.com

Page 150 of 1640

Oil Filte r
Replacemen t
CAUTION: Loose n th e oi l filte r carefull y whil e th e
engin e is hot , th e ho t oi l ma y caus e scalding .
1 . Remov e th e oi l filte r wit h th e specia l too l a s shown .
2 . Inspec t th e thread s an d rubbe r sea l o n th e ne w filter .
Wip e of f th e sea t o n oi l filte r base , the n appl y a ligh t
coa t o f oi l t o th e rubbe r sea l an d instal l th e filter .
3 . Afte r th e rubbe r sea l i s seate d agains t th e base ,
tighte n th e oi l filte r b y turnin g i t approximatel y on e
turn .
Torque : On e tur n (2 2 N- m (2. 2 kg-m , 1 6 lb-ft)) .
OIL FILTE R WRENC H
0791 2-611000 1
Torque : On e tur n
(2 2 N- m (2. 2 kg-m , 1 6 lb-ft) )
4. Star t th e engine , an d chec k th e filte r fo r oi l leakage .
ProCarManuals.com

Page:   < prev 1-10 ... 101-110 111-120 121-130 131-140 141-150 151-160 161-170 171-180 181-190 ... 1640 next >