torque CHRYSLER VOYAGER 1996 User Guide

(11) When vehicle is at correct camber setting
torque both front strut to steering knuckle attaching
bolts to 90 N´m (65 ft. lbs.) plus an additional 1/4
turn after required torque is met.
(12) If Toe readings obtained are not within the
required specification range, adjust Toe to meet the
preferred specification setting. Toe is adjustable
using the following Toe setting procedure.
FRONT TOE SETTING PROCEDURE
(1) Prepare vehicle as described in the Pre-Align-
ment Vehicle Inspection procedure.
(2) Center steering wheel and lock in place using a
steering wheel clamp.
CAUTION: Do not twist front inner tie rod to steer-
ing gear rubber boots during front wheel Toe
adjustment.(3) Loosen front inner to outer tie rod end jam
nuts (Fig. 7). Grasp inner tie rods at serrations and
rotate inner tie rods of steering gear (Fig. 7) to set
front Toe to the preferred Toe specification. See
Alignment Specifications in this group of the service
manual for preferred specification.
(4) Tighten tie rod jam nuts (Fig. 7) to 75 N´m (55
ft.lbs.) torque.
(5) Adjust steering gear to tie rod boots at tie rod.
(6) Remove steering wheel clamp.
SPECIFICATIONS
ALIGNMENT SPECIFICATIONS
All alignment specifications are to be checked and
adjusted with the vehicle at its correct ride height.
Refer to the ride height specifications listed in the
following alignment specifications chart.
Fig. 6 Camber Adjustment Cam Bolt
Fig. 7 Front Wheel Toe Adjustment
NSSUSPENSION 2 - 7
SERVICE PROCEDURES (Continued)

FRONT SUSPENSION
INDEX
page page
DESCRIPTION AND OPERATION
BALL JOINT............................ 11
COIL SPRING........................... 11
FRONT SUSPENSION DESCRIPTION......... 9
HUB AND BEARING ASSEMBLY............ 10
LOWER CONTROL ARM.................. 10
Mc PHERSON STRUT ASSEMBLY........... 10
STABILIZER BAR ATTACHING LINK.......... 10
STABILIZER BAR........................ 10
STEERING KNUCKLE.................... 10
SUSPENSION CRADLE (CROSSMEMBER)..... 9
WHEEL MOUNTING STUDS................ 11
DIAGNOSIS AND TESTING
BALL JOINT (LOWER).................... 12
HUB AND BEARING ASSEMBLY............ 12
LOWER CONTROL ARM.................. 12
Mc PHERSON STRUT.................... 11
STABILIZER BAR........................ 12
STEERING KNUCKLE.................... 12SERVICE PROCEDURES
SUSPENSION CRADLE THREAD REPAIR
PROCEDURE......................... 12
REMOVAL AND INSTALLATION
BALL JOINT............................ 22
FRONT WHEEL MOUNTING STUDS......... 28
HUB AND BEARING ASSEMBLY............ 25
LOWER CONTROL ARM.................. 19
Mc PHERSON STRUT.................... 13
REAR WHEEL MOUNTING STUDS.......... 29
STABILIZER BAR........................ 23
STEERING KNUCKLE.................... 14
DISASSEMBLY AND ASSEMBLY
BALL JOINT SEAL BOOT.................. 33
LOWER CONTROL ARM FRONT BUSHING.... 34
LOWER CONTROL ARM REAR BUSHING..... 35
Mc PHERSON STRUT.................... 30
STABILIZER BAR BUSHING................ 35
SPECIFICATIONS
FRONT SUSPENSION FASTENER TORQUES . . 36
SPECIAL TOOLS
FRONT SUSPENSION.................... 37
DESCRIPTION AND OPERATION
FRONT SUSPENSION DESCRIPTION
An independent Mc Pherson Strut type front sus-
pension is used on these vehicles. Vertical shock
absorbing Mc Pherson Struts attach to the top of the
steering knuckle and to the front strut tower. This
interconnection between the steering knuckle and the
body of the vehicle, provides for the correct steering
knuckle position. This steering knuckle position pro-
vides for the correct front Caster and Camber set-
tings for the vehicle, at the time the vehicle is
designed.
Lower control arms are attached inboard to the
cast aluminum front suspension cradle and outboard
to the bottom of the steering knuckle. Attachment of
the lower control arm to the steering knuckle is done
through a ball joint in the lower control arm.
During steering maneuvers, the strut and the
steering knuckle (through the ball joint and a pivot
bearing in the strut's upper retainer) turn as an
assembly.
SUSPENSION CRADLE (CROSSMEMBER)
This vehicle uses a one piece cast aluminum cradle
for the front suspension. The cradle is used as theattaching points for the lower control arms, stabilizer
bar and steering gear. The cradle also has the power
steering hoses and the chassis brake tubes attached
to it.
The cradle is mounted to the front frame rails at
four points, two on each side of the vehicle. The cra-
dle is isolated from the body of the vehicle using four
isolators, one located at each mounting bolt location.
WARNING: If a threaded hole in the suspension
cradle needs to be repaired, only use the type of
thread insert and installation procedure specified
for this application.
The threaded holes in the cradle that are
used for attachment of the lower control arm
rear bushing retainer, power steering hose and
chassis brake tubes can be repaired. The repair
is done by the installation of a Heli-Coilt
thread insert which has been specifically devel-
oped for this application. Refer to the Mopar
Parts Catalog for the specified Heli-Coil thread
insert to be used for this application. The pro-
cedure for installing the Heli-Coiltthread
insert is detailed in the Service Procedures sec-
tion in this group of the service manual.
NSSUSPENSION 2 - 9

instructions included with the thread insert for the
detailed procedure used for the installation of the
thread insert.
NOTE: The thread inserts for this application are
for the repair of M8x1.25 and M10x1.5 threads. Be
sure the correct tools are used for the required
thread insert size.
TOOL REQUIREMENT FOR M8x1.25 Thread
²8.3mm (5/16 in.) Drill Bit
²120É Countersink
²Heli-CoiltTap #4863-8
²Heli-CoiltGage #4624-8
²Heli-CoiltHand Inserting Tool 7751-8
²Needle Nose Pliers ± For Removal Of Thread
Insert Driving Tang
TOOL REQUIREMENT FOR M10x1.5 Thread
²10.5mm (25/64 in.) Drill Bit
²120É Countersink
²Heli-CoiltTap #4863-10
²Heli-CoiltGage #4624-10
²Heli-CoiltHand Inserting Tool 7751-10
²Needle Nose Pliers ± For Removal Of Thread
Insert Driving Tang
REMOVAL AND INSTALLATION
Mc PHERSON STRUT
REMOVAL
WARNING: DO NOT REMOVE THE NUT FROM THE
STRUT ROD WHILE STRUT ASSEMBLY IS
INSTALLED IN VEHICLE, OR BEFORE STRUT
ASSEMBLY SPRING IS COMPRESSED.
(1) Raise vehicle on jack stands or centered on a
frame contact type hoist. See Hoisting in the Lubri-
cation and Maintenance section of this service man-
ual, for the required lifting procedure to be used for
this vehicle.
(2) Remove the wheel and tire assembly from loca-
tion on front of vehicle requiring strut removal.
(3) If both strut assemblies are to be removed,
mark the strut assemblies right or left according to
which side of the vehicle they were removed from.
(4) Remove the hydraulic brake hose routing
bracket and the speed sensor cable routing bracket
from the strut damper brackets (Fig. 6).
NOTE: When removing nut from stud of stabilizer
bar attaching link, do not allow stud to rotate. Hold
stud from rotating by inserting a Torx Plus 40IP bit
in the end of the stud as shown in (Fig. 7).(5) Remove the stabilizer bar attaching link (Fig.
7) from the bracket on the strut assembly.
CAUTION: The steering knuckle to strut assembly
attaching bolts are serrated and must not be turned
during removal. Remove nuts while holding bolts
stationary in the steering knuckles.
(6) Remove the 2 strut assembly clevis bracket to
steering knuckle attaching bolts (Fig. 8).
(7) Remove the 3 nuts attaching the strut assem-
bly upper mount to the strut tower (Fig. 9).
INSTALLATION
(1) Install strut assembly into strut tower, aligning
and installing the 3 studs on the upper strut mount
into the holes in shock tower. Install the 3 upper
strut mount attaching nut/washer assemblies (Fig.
9). Then using a crow foot. tighten the 3 attaching
nuts to a torque of 28 N´m (250 in. lbs.).
Fig. 6 Brake Hose And Speed Sensor Cable Routing
Fig. 7 Stabilizer Bar Link To Strut Attachment
NSSUSPENSION 2 - 13
SERVICE PROCEDURES (Continued)

CAUTION: The steering knuckle to strut assembly
attaching bolts are serrated and must not be turned
during installation. Install nuts while holding bolts
stationary in the steering knuckles.
(2) Align strut assembly with steering knuckle.
Position arm of steering knuckle into strut assembly
clevis bracket. Align the strut assembly clevis
bracket mounting holes with the steering knuckle
mounting holes. Install the 2 strut assembly to steer-
ing knuckle attaching bolts (Fig. 8).If strut assem-
bly is attached to steering knuckle using a cam
bolt, the cam bolt must be installed in the lower
slotted hole on strut clevis bracket. Also,
attaching bolts should be installed with the
nuts facing the front of the vehicle (Fig. 8).
Tighten the strut assembly to steering knuckle
attaching bolts to a torque of 88 N´m (65 ft. lbs.)
plus an additional 1/4 turn after specified
torque is met.(3) Install stabilizer bar attaching link (Fig. 7) on
bracket of strut assembly. Install stabilizer bar
attaching link to strut bracket attaching nut.
NOTE: When torquing nut on stud of stabilizer bar
attaching link, do not allow stud to rotate. Hold stud
from rotating by inserting a Torx Plus 40IP bit in the
end of the stud as shown in (Fig. 10).
(4) Tighten the stabilizer bar link to strut attach-
ing nut using a Torx Plus 40IP bit and crowfoot as
shown in (Fig. 10) to a torque of 88 N´m (65 ft. lbs.).
(5) Install hydraulic brake hose and speed sensor
cable routing brackets on the strut assembly brackets
(Fig. 6). Tighten the routing bracket attaching bolts
to a torque of 13 N´m (10 ft. lbs.).
(6) Install the wheel/tire assembly on the vehicle.
(7) Install and tighten the wheel mounting stud
nuts in proper sequence until all nuts are torqued to
half specification. Then repeat the tightening
sequence to the full specified torque of 135 N´m (100
ft. lbs.).
STEERING KNUCKLE
REMOVE
(1) Raise vehicle on jack stands or centered on a
frame contact type hoist. See Hoisting in the Lubri-
cation And Maintenance Section of this manual for
the required lifting procedure to be used for this
vehicle.
(2) Remove the cotter pin and nut lock (Fig. 11)
from the end of the stub axle.
(3) Remove the wheel and tire assembly from the
vehicle.
(4) Remove the wave washer (Fig. 12) from the
end of the stub axle
Fig. 8 Strut Damper Attachment To Steering
Knuckle
Fig. 9 Strut Assembly To Strut Tower Attaching
Nuts
Fig. 10 Torquing Stabilizer Bar Link To Strut
Attaching Nut
2 - 14 SUSPENSIONNS
REMOVAL AND INSTALLATION (Continued)

CAUTION: If the vehicle being serviced is
equipped with eccentric strut assembly attaching
bolts, the eccentric bolt must be installed in the
bottom (slotted) hole on the strut clevis bracket
(Fig. 25).
(2) Install steering knuckle back in clevis bracket
of strut damper assembly (Fig. 24). Install the strut
damper to steering knuckle attaching bolts. Tighten
both attaching bolts to a torque of 90 N´m (65 ft. lbs.)
plus an additional 1/4 turn.
(3) Slide drive shaft back into front hub and bear-
ing assembly. Then install steering knuckle onto the
stud of the ball joint assembly (Fig. 23).
(4) Install aNEWsteering knuckle to ball joint
stud, clamping bolt and nut (Fig. 21). Tighten the
clamping bolt and nut to a torque of 145 N´m (105 ft.
lbs.).
(5) Install tie rod end into steering knuckle. Start
attaching nut onto stud of tie rod end. While holding
stud of tie rod end stationary using a 11/32 socket,
(Fig. 17) tighten tie rod end to steering knuckle
attaching nut. Then using a crowfoot and 11/32
socket (Fig. 26), tighten the tie rod end attaching nut
to a torque of 54 N´m (40 ft. lbs.).
(6) Install braking disc on hub and bearing assem-
bly (Fig. 16).
(7) Install disc brake caliper assembly on steering
knuckle. Caliper is installed by first sliding bottom of
caliper under abutment on steering knuckle, and
then rotating top of caliper against top abutment
(Fig. 14).
(8) Install disc brake caliper assembly to steering
knuckle attaching bolts (Fig. 13). Tighten the disc
brake caliper assembly attaching bolts to a torque of
35 N´m (30 ft. lbs.).
(9) Clean all foreign matter from the threads of
the outer C/V joint stub axle. Install the washer and
stub axle to hub/bearing assembly nut on stub axle
and securely tighten nut.(10) Install wheel speed sensor and mounting bolt
(Fig. 19) on steering knuckle. Tighten the speed sen-
sor attaching bolt to a torque of 7 N´m (60 in. lbs.).
(11)
Install front wheel and tire assembly. Install
and tighten the wheel mounting stud nuts in proper
sequence until all nuts are torqued to half the required
specification. Then repeat the tightening sequence to
the full specified torque of 135 N´m (100 ft. lbs.).
(12) Lower vehicle.
(13) With the vehicle's brakes applied to keep hub
from turning, tighten the hub nut to a torque of 203
N´m (150 ft. lbs.) (Fig. 27).
(14) Install the spring wave washer on the end of
the stub axle.
(15) Install the hub nut lock, and anewcotter pin
(Fig. 11). Wrap cotter pin prongs tightly around the
hub nut lock as shown in (Fig. 11).
(16) Set front Toe on vehicle to required specifica-
tion. Use procedure listed under Wheel Alignment, in
the Front Suspension Service Procedures section of
this service manual.
Fig. 25 Correctly Installed Eccentric Attaching Bolt
Fig. 26 Torquing Tie Rod End Attaching Nut
Fig. 27 Torquing Front Stub Axle To Hub Nut
2 - 18 SUSPENSIONNS
REMOVAL AND INSTALLATION (Continued)

suspension cradle (Fig. 36).Do not tighten or
torque pivot bolt at this time.
(2) Install retainer (Fig. 37) attaching rear bush-
ing of lower control arm to front suspension cradle.
When installing retainer, be sure raised rib on
rear bushing (Fig. 37) is positioned in the
groove on the retainer. Do not torque attaching
bolts at this time.
NOTE: If reference marks were not put on the
frame rails prior to lowering the suspension cradle,
Refer to group 13 Frame And Bumpers for the cra-
dle positioning procedure.
(3) Raise the front suspension cradle against the
front frame rails. Align the cradle with the reference
marks on the frame rails.
(4) Tighten the 4 mounting bolts for the front sus-
pension cradle to a torque of 163 N´m (120 ft. lbs.).(5) Install lower control arm ball joint stud into
steering knuckle. Then install the bolt and nut,
clamping the steering knuckle to the ball joint stud
(Fig. 29). Tighten the clamping bolt to a torque of
145 N´m (105 ft. lbs.).
(6) Install the cradle plate on front suspension cra-
dle and then install the 10 cradle plate to cradle
attaching bolts (Fig. 30). Tighten the 9 M-14 attach-
ing bolts (Fig. 30) to a torque of 165 N´m (123 ft.
lbs.). Tighten the 1 M-12 attaching bolt (Fig. 30) to a
torque of 108 N´m (80 ft. lbs.).
CAUTION: When locating jack stands under lower
control arm, do not place the jack stands under the
ball joints (Fig. 38).
(7) Position jack stands under the lower control
arms as close to the ball joints as possible (Fig. 38).
Lower the vehicle onto the jack stands, until the jack
stands are supporting the total weight of the vehicle
(Fig. 38).
(8) Tighten front lower control arm pivot bolt (Fig.
36) to a torque of 183 N´m (135 ft. lbs.) first, then
tighten rear lower control arm bushing retainer
attaching bolts (Fig. 33) to a torque of 68 N´m (50 ft.
lbs.).
(9) Install the wheel/tire assembly on the vehicle.
(10) Install and tighten the wheel mounting stud
nuts in proper sequence until all nuts are torqued to
half specification. Then repeat the tightening
sequence to the full specified torque of 135 N´m (100
ft. lbs.).
(11) Remove jack stands and lower vehicle to the
ground.
Fig. 36 Lower Control Arm Bushing Pivot Bolt
Correctly Installed
Fig. 37 Installing Lower Control Arm Rear Bushing
Retainer
Fig. 38 Jack Stands Supporting Vehicle Weight
NSSUSPENSION 2 - 21
REMOVAL AND INSTALLATION (Continued)

NOTE: When torquing nut on stud of stabilizer bar
attaching link, do not allow the stud to rotate. Hold
stud from rotating by inserting a Torx Plus 40 IP bit
in the end of the the stud (Fig. 47).
(5) Tighten the stabilizer bar attaching link nuts
(Fig. 47) to a torque of 88 N´m (65 ft. lbs.).
(6) Tighten the stabilizer bar bushing retainer to
cradle attaching bolts (Fig. 48) to 68 N´m (50 ft. lbs.)
torque.
(7) Install the cradle plate on front suspension cra-
dle and then install the 10 cradle plate to cradle
attaching bolts (Fig. 46). Tighten the 9 M-14 attach-
ing bolts (Fig. 46) to a torque of 165 N´m (123 ft.
lbs.). Tighten the 1 M-12 attaching bolt (Fig. 46) to a
torque of 108 N´m (80 ft. lbs.).
(8) Lower vehicle.
HUB AND BEARING ASSEMBLY
REMOVE
NOTE: Replacement of the Unit III front hub/bearing
assembly can be normally done without having to
remove the steering knuckle from the vehicle. In the
event that the hub/bearing is frozen in the steering
knuckle and cannot be removed by hand it will have
to be pressed out of the steering knuckle. The
steering knuckle will require removal from the vehi-
cle to allow the hub/bearing assembly to be
pressed out of the steering knuckle. Refer to Front
Steering Knuckle in this section of the service man-
ual for the required removal and installation proce-
dure.
(1) Remove the cotter pin, and nut lock from the
stub axle (Fig. 52).
(2) Remove the spring wave washer (Fig. 53) from
the end of the stub axle.
Fig. 50 Stabilizer Bar Bushing Retainer Installation
Fig. 51 Stabilizer Bar Correctly Positioned In Cradle
Fig. 52 Cotter Pin And Nut Lock
Fig. 53 Nut Lock Wave Washer
NSSUSPENSION 2 - 25
REMOVAL AND INSTALLATION (Continued)

INSTALL
CAUTION: Hub and bearing assembly mounting
surfaces on the steering knuckle and halfshaft (Fig.
60) must be smooth and completely free of foreign
material or nicks prior to installing hub and bearing
assembly.
CAUTION: When installing hub and bearing
assembly into steering knuckle, be careful not to
damage the bearing seal (Fig. 60) on the outer C/V
joint.
(1) Install hub/bearing assembly onto stub axle
and into steering knuckle until squarely seated on
the face of the steering knuckle.
(2) Install the 4 hub/bearing assembly to steering
knuckle attaching bolts (Fig. 58). Equally tighten all
4 mounting bolts in a criss-cross pattern until hub/
bearing assembly is squarely seated against front ofsteering knuckle. Then tighten the 4 hub and bearing
assembly mounting bolts to a torque of 65 N´m (45
ft.lbs.)
(3) Install the hub/bearing assembly to stub shaft
washer and retaining nut (Fig. 61).Tighten, but do
not torque the hub nut at this time.
(4) Install the braking disk on the hub and bearing
assembly.
(5) Install front brake caliper back over braking
disc and align with caliper mounting holes on steer-
ing knuckle (Fig. 55). Caliper is installed by first
installing bottom of caliper under machined abut-
ment on bottom of steering knuckle and then rotat-
ing top of caliper toward steering knuckle. Install the
disc brake caliper to steering knuckle attaching bolts
(Fig. 54) and tighten to a torque of 19 N´m (168 in.
lbs.).
(6) Install wheel and tire assembly on vehicle.
Tighten the wheel mounting stud nuts in proper
Fig. 58 Hub/Bearing Assembly Mounting Bolts
Fig. 59 Hub and Bearing Assembly Removal From
Steering Knuckle
Fig. 60 Hub And Bearing Assembly Mounting
Surfaces
Fig. 61 Hub/Bearing To Stub Axle Washer And
Retaining Nut
NSSUSPENSION 2 - 27
REMOVAL AND INSTALLATION (Continued)

sequence until all nuts are torqued to half specifica-
tion. Then repeat the tightening sequence to the full
specified torque of 129 N´m (95 ft. lbs.).
(7) Lower vehicle to the ground.
CAUTION: When tightening hub/bearing assembly
to stub shaft retaining nut, do not exceed the max-
imum torque of 244 N´m (180 ft. lbs.).
(8) With vehicle brakes applied to keep vehicle
from moving, torque stub shaft to hub/bearing assem-
bly retaining nut to 244 N´m (180 ft. lbs.).
(9) Check the Toe setting on the vehicle and reset
if not within specifications.
FRONT WHEEL MOUNTING STUDS
REMOVE
CAUTION: If a wheel attaching stud needs to be
replaced in the hub and bearing assembly the studs
CAN NOT be hammered out of the hub flange. If a
stud is removed by hammering it out of the bearing
flange, damage to the hub and bearing assembly
will occur leading to premature bearing failure.
The following procedure and special tools shown
MUST BEused when replacing wheel attaching
studs.
The hub and bearing assembly does not require
removal from the steering knuckle to replace wheel
attaching studs in the hub and bearing assembly.
(1) Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubri-
cation and Maintenance section of this manual for
the required lifting procedure to be used for this
vehicle.
(2) Remove the front wheel and tire assembly from
the vehicle.
(3) Remove the front caliper assembly from the
front steering knuckle assembly. (Fig. 62) Refer to
Front Disc Brake Service in the Brake Section of this
service manual for caliper removal procedure.
(4) Remove front rotor from hub, by pulling it
straight off wheel mounting studs. (Fig. 63)
(5) Install a lug nut on the wheel stud to be
removed from the hub and bearing assembly, so the
threads on the stud are even with end of lug nut.
Install Remover, Special Tool C-4150A on hub and
bearing assembly flange and wheel stud (Fig. 64).
(6) Tightening down on special tool will push
wheel stud out of the hub and bearing assembly
flange. When shoulder of wheel stud is past flange
remove special tool from hub and bearing assembly.
Remove lug nut from stud and remove wheel stud
from flange.
INSTALL
(1) Install replacement wheel stud into flange of
hub and bearing assembly. Install washers on wheel
stud, then install a wheel lug nut on stud with flat
side of lug nut against washers (Fig. 65).
(2) Tighten the wheel lug nut, pulling the wheel
stud into the flange of the hub and bearing assembly.
When the head of the stud is fully seated against the
bearing flange, remove lug nut and washers from
wheel stud.
(3) Install the braking disk back on the hub and
bearing assembly. (Fig. 63)
Fig. 62 Disc Brake Caliper Mounting
Fig. 63 Removing Braking Disc
2 - 28 SUSPENSIONNS
REMOVAL AND INSTALLATION (Continued)

(4) Install front brake caliper back over braking
disc and align with caliper mounting holes on steer-
ing knuckle (Fig. 62). Refer to Front Disc Brake Ser-
vice in the Brake Section of this service manual for
caliper installation procedure. Install the caliper
adapter to steering knuckle attaching bolts and
torque to 19 N´m (168 in. lbs.).
(5) Install wheel and tire assembly on vehicle.
Tighten the wheel mounting stud nuts in proper
sequence until all nuts are torqued to half specifica-
tion. Then repeat the tightening sequence to the full
specified torque of 129 N´m (95 ft. lbs.).
(6) Lower vehicle to the ground.
REAR WHEEL MOUNTING STUDS
REMOVE
CAUTION: If a wheel attaching stud needs to be
replaced in the hub and bearing assembly the studs
CAN NOT be hammered out of the hub flange. If astud is removed by hammering it out of the bearing
flange, damage to the hub and bearing assembly
will occur leading to premature hub and bearing
failure.
The following procedure and special tools shown
MUSTbe used when replacing wheel attaching
studs.
The hub and bearing assembly does not require
removal from the rear axle for replacement of the
wheel attaching studs.
(1) Raise vehicle on jackstands or centered on a
frame contact type hoist. See Hoisting in the Lubri-
cation and Maintenance section of this manual, for
the required lifting procedure to be used for this
vehicle.
(2) Remove the rear wheel and tire assembly.
(3) Remove the rear brake drum.
(4) Install a lug nut on the wheel stud to be
removed from the hub and bearing assembly (Fig. 66)
so the threads on stud are even with end of lug nut.
Install Remover, Special Tool C-4150A on hub and
bearing assembly flange and wheel stud (Fig. 66).
(5) Tightening down on special tool will push
wheel stud out of the hub and bearing assembly
flange. Remove lug nut from stud and remove wheel
stud from flange.
INSTALL
(1) Install replacement wheel stud into flange of
hub and bearing assembly. Install washers on wheel
stud, then install a wheel lug nut on stud with flat
side of lug nut against washers (Fig. 67).
(2) Tighten the wheel lug nut, pulling the wheel
stud into the flange of the hub and bearing assembly.
When the head of the stud is fully seated against the
bearing flange, remove lug nut and washers from
wheel stud.
Fig. 64 Wheel Stud Removal From Hub/Bearing
Assembly
Fig. 65 Installing Wheel Stud Into Hub And Bearing
Fig. 66 Removing Wheel Stud From Hub And
Bearing
NSSUSPENSION 2 - 29
REMOVAL AND INSTALLATION (Continued)