Citroen C4 2016 2.G Owner's Manual

189
C4-2_en_Chap06_conduite_ed02-2015
Deactivation
Going into engine START mode
At any time, press the "ECO OFF" switch to
d eactivate   the   system.
This
  is   confirmed   by   the   switch   warning   lamp  
c

oming   on   accompanied   by   the   display   of   a  
m

essage.
Special cases: START invoked
automatically
The "ECO"  warning   lamp   goes   off  a
nd   the   engine   starts   automatically:
-

w

ith a manual gearbox , when you fully
depress the clutch pedal,
-

w

ith an automatic gearbox:
●
 
g

ear   selector   in   position   D or M, when
you
  release   the   brake   pedal,
●
 
o

r
 
gear   selector   in   position   N   and   brake  
p

edal   released,   when   you   place   the   gear  
s

elector in position D or M ,
●
 
o

r
 
when   you   engage   reverse   gear.For
  safety   reasons   or   to   ensure   smooth  o
peration,   START   mode   is   invoked  
a

utomatically
 w
hen:
-
 
y
ou   open   the   driver's   door,
-
 
y
ou   unfasten   the   driver's   seat   belt,
-
 
t
he   speed   of   the   vehicle   exceeds   15   mph  
(

25   km/h)   with   a   manual   gearbox   (3   km/h  
(

2   mph)   with   PureTech   130   petrol   and  
B

lueHDi   Diesel   115   and   120   versions)   or  
2 m

ph   (3   km/h)   with   an   automatic   gearbox,
-
 
t
he   electric   parking   brake   is   being   applied,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
In this case the "ECO"
 

warning   lamp  
f

lashes   for   few   seconds,   then   goes  
o

f f.
This operation is perfectly normal.
With
  a   manual   gearbox   in   STOP   mode,  
i

f
 
a
  gear   is   engaged   without   fully  
d

epressing   the   clutch   pedal,   a   warning  
l

amp   comes   on   or   an   alert   message  
i

s
 
displayed   asking   you   to   depress   the  
c

lutch   pedal   to   restart   the   engine. If
  the   system   has   been   deactivated  
i

n   STOP   mode,   the   engine   restarts  
i

mmediately.
6
Driving

190
C4-2_en_Chap06_conduite_ed02-2015
Maintenance
In the event of a malfunction with the system, the "ECO OFF"   switch   warning   lamp   flashes,  
t

hen   comes   on   continuously.
have
  it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
Operating fault
This system requires the use of a 12 V battery of   specific   technology   and   characteristics  
(

reference   numbers   available   from   a   CITROËN  
d

ealer   or   a   qualified   workshop).
Fitting
  a   battery   not   listed   by   CITROËN would  
i

ntroduces   the   risk   of   faults   with   the   system.
Before
  doing   any   work   under   the  
b

onnet, deactivate the Stop & Start
system   to   avoid   the   risk   of   injury   related  
t

o   an   automatic   change   to   START  
m

ode.
The   Stop   &   Start   system   makes   use   of  
a

n   advanced   technology.   All   work   on  
t

his   type   of   battery   must   only   be   carried  
o

ut   by   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 
mode,
 
t

he
 
vehicle
 
may
 
stall.
 
All
 
of
 
the
 
i

nstrument
 
panel
 
warning
 
lamps
 
come
 
o

n.
Depending
 
on
 
version,
 
an
 
alert
 
m

essage
 
may
 
also
 
be
 
displayed
 
asking
 
y

ou
 
to
 
put
 
the
 
gear
 
lever
 
into
 
position
 
N
and
 
put
 
your
 
foot
 
on
 
the
 
brake
 
pedal.
It is then necessary to switch off the
ignition,
 
then
 
restart
 
the
 
engine
 
using
 
t

he
 
key
 
or
 
the
 
"START/STOP"
 
button.
Reactivation
The system is reactivated automatically a t   every   new   start   using   the   key   or   the  
"

START/STOP"   button.
Press the "ECO OFF"
  switch   again.
The
 
system   is   active   again;   this   is   confirmed  
b

y
 
the
  switch   warning   lamp   going   off   and   the  
d

isplay   of   a   message.
Driving

191
C4-2_en_Chap06_conduite_ed02-2015
Hill start assist
On an ascending slope, with the vehicle
stationar y, the vehicle is held for a brief
moment when you release the brake pedal:
- 
i
f   you   are   in   first   gear   or   neutral   with   a  
m

anual
 g
earbox,
-

i
f you are in position D or M with an
automatic
  gearbox.
Operation
On a descending slope, with the vehicle
stationary and reverse gear engaged, the
vehicle is held for a brief moment when you
release the brake pedal.
Operating fault
If a fault occurs with the system, these warning lamps   come   on.   Contact   a   CITROËN   dealer  
o

r   a   qualified   workshop   to   have   the   system  
c

hecked.
System
 
which
 
keeps
 
your
 
vehicle
 
immobilised
 
t

emporarily
 
(approximately
 
2
 
seconds)
 
when
 
s

tarting
 
on
 
a
 
gradient,
 
the
 
time
 
it
 
takes
 
to
 
m

ove
 
your
 
foot
 
from
 
the
 
brake
 
pedal
 
to
 
the
 
a

ccelerator
 ped

al.
This
 
function
 
is
 
only
 
active
 
when:
-
 
t

he
 
vehicle
 
is
 
completely
 
stationary,
 
with
 
y

our
 
foot
 
on
 
the
 
brake
 
pedal,
-
 
w

hen
 
certain
 
conditions
 
of
 
gradient
 
are
 
m

et,
-
 
w

ith
 
the
 
driver’s
 
door
 
closed.
The hill start assist function cannot be
deactivated.
Do
 
not
 
leave
 
the
 
vehicle
 
while
 
it
 
is
 
being
 
h

eld
 
in
 
the
 
hill
 
start
 
assist
 
phase.
If you need to leave the vehicle while
the
 
engine
 
is
 
running,
 
apply
 
the
 
parking
 b
rake
 
manually
 
then
 
ensure
 
that
 
the
 p
arking
 
brake
 
warning
 
lamp
 
is
 
on
 
(not
 
f

lashing)
 
in
 
the
 
instrument
 
panel.
6
Driving

192
C4-2_en_Chap06_conduite_ed02-2015
Tyre under-inflation detection
System which automatically checks the p
ressures   of   the   tyres   while   driving.
The
  system   continuously   monitors   the  
p

ressures of the four tyres, as soon as the
vehicle
  is   moving.
A pressure sensor is located in the valve of
each
  tyre   (except   the   spare   wheel).
The
  system   triggers   an   alert   if   a   drop   in  
p

ressure   is   detected   in   one   or   more   tyres.
The
  tyre   under-inflation   detection   system   is   an  
a

id   to   driving   which   does   not   replace   the   need  
f

or   vigilance   on   the   part   of   the   driver.This
  system   does   not   avoid   the   need  
t

o   check   the   tyre   pressures   regularly  
(

including   the   spare   wheel)   and   before  
a

  long   journey.
Driving   with   under-inflated   tyres  
a

dversely   affects   road   holding,  
e

xtends   braking   distances   and   causes  
p

remature   tyre   wear,   particularly   under  a
rduous   conditions   (vehicle   loaded,  h
igh   speed,   long   journey).The tyre pressures for your vehicle can
be
  found   on   the   tyre   pressure   label.
The   tyre   pressures   must   be   checked  
w

hen   the   tyres   cold   (vehicle   stopped  
f

or   1   hour   or   after   driving   for   less   then  
6

  miles   (10   km)   at   moderate   speed).  
O

ther wise,   add   0.3   bar   to   the   values  
i

ndicated   on   the   label.
For m ore i nformation o n id entification m
arkings,   including   the   tyre   pressure  
l

abel,   refer   to   the   corresponding  
s

ection.
Driving
  with   under-inflated   tyres  
i

ncreases   fuel   consumption.
Driving

193
C4-2_en_Chap06_conduite_ed02-2015
The flashing and then fixed illumination   of   the   under-inflation w

arning   lamp   accompanied   by   the
 i

llumination   of   the   service   warning
 l

amp   indicates   a   fault   with   the   system.
Operating fault
The alert is given by the fixed illumination   of   this   warning   lamp,  
a

ccompanied   by   an   audible   signal,  
a

nd   depending   on   equipment,   the  
d

isplay   of   a   message.
Under-inflation alert
In the event of a problem on one of the tyres, the   symbol   or   the   message   appears,   according  
t

o   equipment,   to   identify   it.
F
 
R
educe   speed,   avoid   sudden   steering  
m

ovements   or   harsh   brake   applications.
F
 
S
top   as   soon   as   it   is   safe   to   do   so. In
  this   case,   monitoring   of   the   tyre   pressures   is  
n

ot   assured.
F  
I
f   you   have   a   compressor   (the   one   in   the  
t

emporary   puncture   repair   kit   for   example),  
c

heck   the   four   tyre   pressures   when   cold.
 I

f   it   is   not   possible   to   check   the   tyre  
p

ressures   at   the   time,   drive   carefully   at  
r

educed
 s
peed.


or
F
I
n the event of a puncture, use the
temporary   puncture   repair   kit   or   the   spare  
w

heel   (according   to   equipment).
Go   to   a   CITROËN   dealer   or   a   qualified  w
orkshop to   have   the   system   checked   or,  
f

ollowing   the   repair   of   a   puncture,   to   have   the  
o

riginal   wheel,   equipped   with   a   sensor,   refitted.
Any
  tyre   repair   or   replacement   on   a   wheel  
f

itted   with   this   system   must   be   carried   out   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
If
  after   changing   a   tyre,   a   wheel   is   not   detected  
b

y   your   vehicle   (fitting   snow   tyres   for   example),  
y

ou   must   have   the   system   reinitialised   by   a  
C

ITROËN   dealer   or   a   qualified   workshop.
The loss of pressure detected does not
always
  lead   to   visible   deformation   of  
t

he   tyre.
Do
  not   rely   on   just   a   visual   check.This alert is also displayed when one or
more
  wheels   is   not   fitted   with   a   sensor  
(

for   example,   a   space-saver   or   steel  
spar

e
 w
heel).
The   alert   is   maintained   until   the   tyre   or  t
yres concerned is reinflated, repaired
or   replaced.
The
  spare   wheel   (space-saver   type   or   a  
s

teel   rim)   does   not   have   a   sensor.
6
Driving

194
C4-2_en_Chap06_conduite_ed02-2015
Lane departure warning system
Activation
Deactivation
DetectionOperating fault
System which detects the involuntary crossing o
f   longitudinal   traffic   lane   markings   on   the  
g

round   (solid   or   broken   line).
Sensors,
  fitted   below   the   front   bumper,   trigger  
a

  warning   if   the   vehicle   drifts   over   a   lane  
m

arking   (speed   higher   than   50   mph   (80   km/h)).
This
  system   is   particularly   useful   on   motor ways  
a

nd   main   roads. In
  the   event   of   a   malfunction,   the  
s

ervice   warning   lamp   comes   on,  
a

ccompanied   by   an   audible   signal  
a

nd   a   message   in   the   screen.
Contact   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
The   lane   departure   warning   system  
c

annot   in   any   circumstances   replace  
t

he   need   for   vigilance   on   the   part   of   the  
d

river.
It
  is   necessary   to   observe   driving  
r

egulations   and   take   a   break   every  
t

wo hours. The
  detection   may   be   impeded:
- i f   the   sensors   are   dirty   (mud,   snow...),
-
 
i
f   the   markings   on   the   ground   are  
w

orn,
-

i
f there is little contrast between the
markings
  on   the   ground   and   the  
r

oad   sur face.
You
  are   warned   by   the   vibration   of   the   driver's  
s

eat   cushion:
-
 
o
n   the   right-hand   side,   if   the   marking   on  
t

he   ground   has   been   crossed   on   the   right,
-
 
o
n   the   left-hand   side,   if   the   marking   on   the  
g

round   has   been   crossed   on   the   left.
No
  warning   is   transmitted   while   the   direction  
i

ndicator   is   active   and   for   approximately  
2

0 seconds after the direction indicator is
switched
  off.
A
  warning   may   be   transmitted   if   a   direction  
m

arking   (e.g.   arrow)   or   non-standard   marking  
(

e.g.   graffiti)   is   crossed.
F
 
W
hen   switching   the   ignition   on   or   with  
t

he   engine   running,   press   this   button;   the  
i

ndicator   lamp   comes   on.
F  
P
ress   this   button   again,   the   indicator   lamp  
g

oes   off.
The   status   of   the   system   remains   in   the  m
emory   when   the   ignition   is   switched   off.
Driving

195
C4-2_en_Chap06_conduite_ed02-2015
Blind spot sensors
This driving assistance system warns the driver of the presence of another vehicle in the blind
spot
  angle   of   their   vehicle   (areas   masked   from  
t

he   driver's   field   of   vision),   as   soon   as   this  
p

resents   a   potential   danger.
Operation
F On  switching   on   the   ignition,   or   engine  r
unning,   press   this   button   to   activate   the  
f

unction;   the   warning   lamp   comes   on.
Sensors
  fitted   in   the   front   and   rear   bumpers  
m

onitor   the   blind   spots.
A
 
warning
 
lamp
 
appears
 
in
 
the
 
door
 
mirror
 
on
 t
he
 
side
 
in
 
question:
-
 i
mmediately,
 
when
 
being
 
overtaken,
-

a

fter a delay of about one second, when
overtaking
 
a
 
vehicle
 
slowly.
This
 
system
 
is
 
designed
 
to
 
improve
 
s

afety
 
when
 
driving
 
and
 
is
 
in
 
no
 
c

ircumstances
 
a
 
substitute
 
for
 
the
 
use
 
o

f
 
the
 
interior
 
rear
 
view
 
mirror
 
and
 
door
 
m

irrors.
 
It
 
is
 
the
 
driver's
 
responsibility
 
to
 
c

onstantly
 
check
 
the
 
traffic,
 
to
 
assess
 
t

he distances and relative speeds
of other vehicles and to predict their
movements
 
before
 
deciding
 
whether
 
to
 
c

hange
 lan

e.
The
 
blind
 
spot
 
sensor
 
system
 
can
 
never
 
r

eplace
 
the
 
need
 
for
 
vigilance
 
on
 
the
 
p

art
 
of
 
the
 
driver.
6
Driving

196
C4-2_en_Chap06_conduite_ed02-2015
No alert will be given in the following situations:
-  i n   the   presence   of   immobile   objects  
(

parked   vehicles,   barriers,   street   lamps,  
r

oad
 s
igns...),
-
 
w
ith   vehicles   moving   in   the   opposite  
d

irection,
-
 
d
riving   on   a   sinuous   road   or   a   sharp  
c

o r n e r,
The
 
alert
 
is
 
given
 
by
 
a
 
warning
 
lamp
 
which
 
c

omes
 
on
 
in
 
the
 
door
 
mirror
 
on
 
the
 
side
 
in
 
q

uestion
 
as
 
soon
 
as
 
a
 
vehicle
 
-
 
car,
 
lorry,
 

cycle
 
-
 
is
 
detected.
For
 
this,
 
the
 
following
 
conditions
 
must
 
be
 
met:
-
 
a

ll
 
the
 
vehicles
 
must
 
be
 
moving
 
in
 
the
 
sa

me
 d

irection,
-
 
t

he
 
speed
 
of
 
your
 
vehicle
 
is
 
between
 
7
 
and
 
7

5
 
mph
 
(12
 
and
 
140
 
km/h),
-
 
w

hen
 
you
 
overtake
 
a
 
vehicle
 
with
 
a
 
speed
 
d

ifference
 
of
 
less
 
than
 
6
 
mph
 
(10
 
km/h),
-
 
w

hen
 
a
 
vehicle
 
overtakes
 
you
 
with
 
a
 
speed
 
d

ifference
 
of
 
less
 
than
 
15
 
mph
 
(25
 
km/h),
-
 
t

he
 
traffic
 
must
 
be
 
flowing
 
normally,
-
 
i

n
 
the
 
case
 
of
 
an
 
overtaking
 
manoeuvre,
 i
f
 
this
 
is
 
prolonged
 
and
 
the
 
vehicle
 
being
 ov
ertaken
 
remains
 
in
 
the
 
blind
 
spot,
-
 
y

ou
 
are
 
driving
 
on
 
a
 
straight
 
or
 
slightly
 
c

urved road,
-
 
y

our
 
vehicle
 
is
 
not
 
pulling
 
a
 
trailer,
 
a
 
c

aravan... -
 w hen   overtaking   (or   being   overtaken   by)   a  v
ery   long   vehicle   (lorry,   coach...)   which   is  
a

t   the   same   time   detected   at   the   rear   in   the  
b

lind   spot   angle   and   present   in   the   driver's  
f

orward field of vision,
-
 
i
n   very   heavy   traffic:   vehicles   detected   in  
f

ront and behind are confused with a lorry
or
  a   stationary   object,
-
 
w
hen   overtaking   quickly.
Driving

197
C4-2_en_Chap06_conduite_ed02-2015
F To  deactivate   the   system,   press   this   button  a
gain;   the   warning   lamp   goes   off.
The
  state   of   the   system   remains   in   memory   on  
s

witching   off   the   ignition.
Operating fault
The system is automatically deactivated when   towing   with   a   towbar   approved   by  
CIT

ROËN. The
  system   may   suffer   temporary  
i

nterference in certain weather
conditions   (rain,   hail...).
In   particular,   driving   on   a   wet   sur face  
o

r   moving   from   a   dry   area   to   a   wet   area  
c

an   cause   false   alerts   (for   example,   the  
p

resence   of   a   fog   of   water   droplets   in  
t

he   blind   spot   angle   is   interpreted   as   a  
v

ehicle).
In bad or wintry weather, ensure that
the   sensors   are   not   covered   by   mud,   ice  
o

r   snow.
Take   care   not   to   cover   the   warning   zone  
i

n   the   door   mirrors   or   the   detection  
z

ones   on   the   front   and   rear   bumpers  
w

ith   adhesive   labels   or   other   objects;  
t

hey   may   hamper   the   correct   operation  o
f   the   system.
In   the   event   of   a   fault,   the   warning   lamp   in   the  
b

utton   flashes   then   goes   off.
Have   it   checked   by   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop.
6
Driving

198
C4-2_en_Chap06_conduite_ed02-2015
6. Speed  limiter   on   /   pause   indication.
7. S peed   limiter   mode   selection   indication.
8.
 P

rogrammed   speed   value.
9.
 S

election   of   a   memorised   speed   setting.
Displays in the instrument panel
Speed limiter
1. Speed  limiter   mode   selection   wheel.
2. P rogrammed   value   decrease   button.
3.
 P

rogrammed   value   increase   button.
4.
 S

peed   limiter   on   /   pause   button.
5.
 D

isplay   memorised   speed   settings   button.
Steering mounted controls
System which prevents the vehicle from exceeding the speed programmed by the driver.
The speed limiter is switched on manually.
The   minimum   programmed   speed   is 2

0 mph   (30   km/h).
The
  programmed   speed   remains   in   the
 s

ystem   memory   when   the   ignition   is
 s

witched   off.
The speed limiter is a driving aid that cannot,   in   any   circumstances,   replace   the n

eed   to   observe   speed   limits   or   the   need
 f

or   vigilance   on   the   part   of   the   driver.
Driving