FIAT DOBLO 2008 1.G Owners Manual

130IN AN EMERGENCY
IF A BULB BURNS OUT
Modifications or repairs
to the electrical system
carried out incorrectly
and without bearing the features
of the system in mind can cause
malfunctions with the risk of fire.Only touch the metal
part when handling halo-
gen bulbs. If the transpar-
ent bulb is touched it reduces the
intensity of the light emitted and
can also reduce the life of the
bulb. If you touch the bulb acci-
dentally, rub it with a cloth moist-
ened with alcohol and leave it to
dry.
You should have the
bulbs replaced at a Fiat
Dealership. Always check
the height of the headlight beam
after changing a bulb.
Halogen bulbs contain
pressurised gas which, if
broken, may cause small
fragments of glass to be project-
ed outwards.
GENERAL INSTRUCTIONS
– When a light is not working, check
that it has not fused before changing
the bulb.
– For the location of the fuses, re-
fer to “If a fuse blows” in this chap-
ter.
– Before replacing a bulb that does
not work, check that the contacts are
not oxidised.
– Burnt-out bulbs must be replaced
with ones of the same type.
– Always check the height of the
headlight beam after changing a bulb.
IMPORTANTThe headlight inner
surface may be lightly misted over: this
is not a fault but a natural fact due to
low temperature and the level of air
humidity. It will disappear as soon the
headlights are turned on. The pres-
ence of drops inside the headlights
means water infiltration, therefore
contact Fiat Dealership.
119-148 Doblo GB 9-05-2008 12:09 Pagina 130

131IN AN EMERGENCY
TYPES OF BULBS
Several types of bulbs are installed in
the vehicle fig. 17:
A Glass bulbs
Clipped into position.
To remove them, pull.B Bayonet connection bulbs
Remove from the bulb holder by
pressing the bulb and turning it
anticlockwise.
C Cylindrical bulbs
Remove by pulling away from
terminals.D-E Halogen bulbs
To remove the bulb, release
the clip holding the bulb in
place.
A
B
C
E
D
fig. 17
F0A098b
Fig. 17
E
D
A
B
A
E
B
B
B
B
B
A
C
APower
55W
55W
5W
21W
5W
55W
21/5W
21W
21W
21W
21W
5W
10W
10W
5W Type
H1
H7
W5W
PY21W
W5W
H1
P21W/5W
P21W
PY21W
P21W
P21W
W5W
C10W
W5WBulb
Main beam headlights
Dipped beam headlights
Front sidelights
Front direction indicators
Side direction indicators
Front fog lights
Taillights and brake lights
Third brake light
(supplementary brake lights)
Rear direction indicators
Reversing light
Rear fog light
Number plate light
Ceiling light:
– with toggle lens
– with map reading light
Boot
119-148 Doblo GB 9-05-2008 12:09 Pagina 131

132IN AN EMERGENCY
See “If a bulb burns out” in this chap-
ter for bulb type and power.MAIN BEAM HEADLIGHTS
To change the halogen bulb, proceed
as follows:
1)Remove the protection cover C-
fig. 18turning it counterclockwise;
2)Release clip A-fig. 19, remove
connector Band remove the bulb C.DIPPED BEAMS
To change the halogen bulb, proceed
as follows:
1)Remove the protection cover B-
fig. 18turning it counterclockwise;
2)Release clip A-fig. 20, remove
connector Band remove the bulb C.
IF AN EXTERIOR LIGHT BURNS OUT
Alterations or repairs to
the electric system not
carried out correctly and
without taking into account the
system specifications may cause
failures and the risk of fire.
fig. 18
F0A0523b
fig. 19
F0A0521b
fig. 20
F0A0522b
119-148 Doblo GB 9-05-2008 12:09 Pagina 132

133IN AN EMERGENCY
FRONT SIDELIGHTS
To change the bulb, proceed as fol-
lows:
1)Remove the protection cover B-
fig. 18turning it counterclockwise;
2)Press tabs A-fig. 21, remove the
bulb holder from housing Band re-
move the bulb C(clipped in).FRONT DIRECTION
INDICATORS
To change the bulb, proceed as fol-
lows:
1)Turn the bulb holder A-fig. 18
and remove it.
2)Remove bulb by pushing it slight-
ly and turning it anticlockwise (bayo-
net coupling).
AA
B
fig. 21
F0A0123b
FRONT FOG LIGHTS
(where provided)
Contact Fiat Dealershipto have
front fog lights A-fig. 22replaced.
A
fig. 22
F0A0121b
119-148 Doblo GB 9-05-2008 12:09 Pagina 133

134IN AN EMERGENCY
REAR LIGHT CLUSTER
To replace a bulb, proceed as fol-
lows:
Versions equipped with rear
brackets:
1)Working inside the vehicle: re-
move the plastic cover fig. 25set on
the speaker seat fitting the screwdriv-
er under the plastic and making it slide
in parallel with the slot to spring the
2 front catches, pull the plastic cover
parallel with the supporting surface to
spring the rear catch and then remove
the upper plastic cover A-fig. 26us-
ing the screwdriver provided, in order
to make visible the fastening bolt Bof
the light unit.Versions not equipped with rear
brackets:
1)Act from inside the vehicle to re-
move upper plastic cap C-fig. 27by
means of the screwdriver available, so
that light cluster fastening bolt Dis
made visible.
AB
fig. 26
F0A0146b
DC
fig. 27
F0A0147b
fig. 25
F0A0149b
SIDE DIRECTION
INDICATORS
To change the bulb, proceed as fol-
lows:
1)Press the lens A-fig. 24in the di-
rection of the arrow so to compress
the clip and remove the cluster.
2)Turn the bulb holder counter-
clockwise, remove the snap-fitted bulb
and replace it.
fig. 24
F0A0524b
119-148 Doblo GB 9-05-2008 12:09 Pagina 134

135IN AN EMERGENCY
2)Fit the wrench provided A-fig. 28
(used also to remove the wheel) to
the fastening bolt of the light unit.
3)Loosen the bolts, then undo the
light cluster fastening nuts by means of
extension B-fig. 28supplied with the
unit.
As regards the 7-seater version is
concerned, undo the light cluster fas-
tening bolt by means of extension B-
fig. 28 inserted onto the bolt through
slotted hole C-fig. 28a.
4)Undo, after removing the fasten-
ing bolt, the cluster fastening screws
(located outside), as illustrated in
fig. 29.5)Take out the pressure-fit con-
nector.
6)Undo the four fastening screws to
remove the bulb holder and get access
to the bulbs.
7)Remove the bulbs fig. 30by push-
ing them gently and turning them
counterclockwise (bayonet fitting)
A– brake light bulb
B– indicator light bulb
C– reversing light bulb
D– sidelight bulb
E– rear fog light bulb
fig. 28a
F0A0406b
fig. 29
F0A0525b
fig. 30
F0A0526b
fig. 28
F0A0401b
119-148 Doblo GB 9-05-2008 12:09 Pagina 135

136IN AN EMERGENCY
THIRD BRAKE LIGHTS
To replace a bulb, open either the
left-hand door or the tailgate and
loosen the screws A-fig. 31.
Remove the lens from its housing
from the outside.
Remove the clipped-on bulb B-fig.
32and replace it.NUMBER PLATE LIGHT
To replace a bulb, press the tab in
the point shown in fig. 33and remove
the cluster. Turn the bulb holder A-
fig. 34anticlockwise and remove bulb
B. IF AN INTERIOR
LIGHT BURNS OUT
fig. 31
F0A0528b
B
fig. 32
F0A0144b
fig. 33
F0A0527b
fig. 34
F0A0529b
Modifications or repairs
to the electrical system
carried out incorrectly
and without bearing the features
of the system in mind can cause
malfunctions with the risk of fire.
See “If a bulb burns out” in this chap-
ter for bulb type and power.
119-148 Doblo GB 9-05-2008 12:09 Pagina 136

137IN AN EMERGENCY
CEILING LIGHTS
With toggling lens
To replace a bulb:
1)Remove the ceiling lightfig. 35by
releasing the clipped on lens frame in
the point shown by the arrow.
2)Open the container A-fig. 36and
replace the burnt-out bulb.With map reading lights
To replace a bulb:
1)Remove the ceiling lightA-fig. 37
by releasing the clipped on lens frame
in the point shown by the arrow.
2)Open the bulb container A-fig.
38.
3)Replace the burnt out bulb.BOOT LIGHT
To replace the bulb:
1)Remove the lens A-fig. 39as
shown by the arrow.
2)Open the bulb holder Band re-
move the bulb C(clipped in).
fig. 35
F0A0142b
A
fig. 36
F0A0200b
A
fig. 37
F0A0140b
A
fig. 38
F0A0172b
ABC
fig. 39
F0A0138b
119-148 Doblo GB 9-05-2008 12:09 Pagina 137

138IN AN EMERGENCY
IF A FUSE BLOWS
GENERAL
A fuse is an element for protecting
the electrical system. A fuse will trip
(i.e. it will blow) in the event of a fail-
ure or improper interventions in the
electrical system.
If an electrical device is not working,
check whether the respective fuse is
blown. The conductor A-fig. 40
should be intact. If it is not, replace the
fuse with another with the same am-
perage (same colour).
B- Undamaged fuse.
C- Fuse with broken filament.Remove the blown fuse with the
tongs provided D, which can be found
in the fusebox.
D
B
C
A
fig. 40
F0A0118b
Never replace a broken
fuse with anything other
than a new fuse. Always
use a fuse of the same colour.
Never change a fuse
with another amperage:
FIRE RISK.
Do not attempt to re-
pair a blown MAXI-FUSE.
Go to a Fiat Dealership.
Before changing a fuse,
check the ignition key has
been removed and that
all the other electric devices have
been turned off/disabled.
If the fuse blows again,
have the vehicle inspect-
ed at a Fiat Dealership.
119-148 Doblo GB 9-05-2008 12:09 Pagina 138

139IN AN EMERGENCY
The fuses in the Fiat Doblò are
grouped in two fuseboxes, one locat-
ed in the dashboard and the other in
the engine compartment.
Press in the points shown in fig. 41
to remove the cover and reach the
fuses.
Refer to the table on the following
pages to identify the fuses.
fig. 41
F0A0151b
F48F49F35F13
F46F37F42F12
F45F47F32F50F51
F52F41F43F40F44
F36F39F38F53F31F34
F33
119-148 Doblo GB 9-05-2008 12:09 Pagina 139