lock FORD MUSTANG 1969 Volume One Chassis

02-02-38
Brake System

02-02-38

2.
Disconnect the actuator solenoid

and warning switch harness connectors

from the control module.

3.
Remove the two wiring harness

grommets from the dash panel and

push the wiring harness and connec-

tors through the openings in the dash

panel.

4.
Working in the engine compart-

ment loosen the hose clamp and re-

move the air hose from the air filter.

5.
Remove the engine air cleaner-

Loosen the hose clamp and remove

the vacuum hose from the vacuum

manifold fitting.

6. Raise the vehicle on a hoist.

7.
Disconnect the exhaust pipes

from the exhaust manifold and sup-

port with wire to provide access to the

actuator assembly.

8. Remove the bolt retaining the

actuator ground wire to the rear outer

corner of the engine right bank.

9. Loosen the tube nuts and discon-

nect the brake system hydraulic tubes

from the hydraulic valve housing.

10.
Remove the three nuts retaining

the actuator assembly to the actuator

support bracket.

11.
Remove the three bolts that re-

tain the actuator mounting bracket to

the side rail and remove the mounting

bracket.

12.
Remove the actuator assembly

from the vehicle and place it on a

bench.

13.
Remove the air and vacuum

hoses from the actuator.

INSTALLATION

1.
Install the air and vacuum hoses

on the new actuator.

2.
Place the actuator assembly into

position under the vehicle, routing the

air and vacuum hoses up between the

engine and fender apron and inserting

the solenoid leads through the holes in

the firewall.

3.
Position the ground wire to the

rear of the engine block and install re-

taining bolt.

4.
Position the actuator mounting

bracket to the frame side rail and in-

stall the three retaining bolts.

5.
Position the actuator assembly

to the mounting bracket and install

the three retaining nuts.

6. Connect the hydraulic tubes to

the hydraulic valve assembly and

tighten the tube nuts to specifications.

7.
Connect the exhaust pipes to the

exhaust manifolds.

8. Lower the vehicle.

9. Pull the actuator solenoid and

brake warning switch wiring harness
through the two holes in the dash

panel from inside the car. Seat the

wiring harness grommets in the dash

panel.

10.
Connect the actuator solenoid

and brake warning switch wiring har-

ness connectors to the control mo-

dules.
'

11.
Position the control module in

the bracket under the glove box and

install the retaining screw.

12.
In the engine compartment con-

nect the air hose to the air filter and

position the hose clamp.

13.
Connect the vacuum hose to the

engine vacuum manifold fitting. In-

stall the engine air cleaner.

14.
Bleed the rear brake system and

centralize the pressure differential

valve.

15.
Raise the rear wheels. Apply

the brakes with the rear wheels turn-

ing to verify proper operation of the

anti-skid control system.

ANTI-SKID CONTROL MODULE

REMOVAL

Refer to Fig. 39.

1.
Remove the retaining strap hold-

ing the harnesses.

2.
Remove the screw that attaches

the forward end of the control module

retainer to the support assembly.

3.
Lower the forward end of the

control module and retainer from the

support assembly; move the module

and retainer forward slightly until the

flange clears the slot in the support

assembly.

4.
Disconnect the five wiring har-

ness plugs from the control module.

5.
Remove the control module from

the vehicle.

INSTALLATION

1.
Connect the five wiring harness

plugs to the control module. Only one

arrangement is possible.

2.
Position the control module in

the retainer, orienting the module per

the markings on it, and insert the re-

tainer flange into the slot at the rear

of the support assembly.

3.
Pivot the retainer and control

module upward and align the screw

hole in the forward end of the retainer

with the hole in the support bracket

assembly. Install the retaining screw.

4.
Test the vehicle on the hoist to

verify correct operation of the skid

control system.
5.-
Secure the wiring to the module

support extension with the retaining

strap.

ANTI-SKID CONTROL SENSOR

REMOVAL

Refer to Fig. 39.

1.
Raise the vehicle on a hoist.

2.
Remove the rear wheel and tire

assembly.

3.
Remove the three Tinnerman

nuts (3) and remove the brake drum.

4.
Disconnect the sensor lead from

the rear wiring harness.

5.
Unseat the sensor lead grommet

pushing it to the inside of the brake

assembly.

6. Remove the four nuts that retain

the sensor to the backing plate and

pull the axle shaft, sensor assembly

and wheel bearing assembly from the

axle housing.

7.
Press the wheel bearing retainer

and wheel bearing off the axle shaft

(Refer to Part 4-2).

8. Remove the sensor assembly and

press the rotor off the shaft with tool

T69P-2B384-A Detail 2 and TOOL

1225-DA.

INSTALLATION

1.
Press a new rotor onto the axle

shaft. Install a new sensor assembly

on the shaft with tool T69P-

2B384-ADetail 1 and TOOL 1225-

DA, and press the bearing and bear-

ing retainer onto the shaft (Refer to

Part 4-2).

2.
Insert the axle shaft assembly in

the rear axle housing onto the four

backing plate retaining bolts, feeding

the sensor lead through the hole in the

backing plate.

3.
Seat the sensor lead grommet in

the backing plate.

4.
Install the four nuts on the re-

taining bolts and tighten to specifica-

tions.

5.
Connect the sensor lead to the

rear wiring harness and install two re-

taining straps.

6. Install the rear brake drum and

retain with the Tinnerrhan drum re-

taining nuts.

7.
Install the rear wheel and tire as-

sembly and tighten the wheel nuts to

specifications.

8. Test the vehicle on the hoist to

verify proper operation of the skid

control system.procarmanuals.com

02-02-41
Brake System

02-02-41

bolt and G-ring in the bottom of the

master cylinder.

8. Install the bleed screw (if so

equipped). Install the gasket (dia-

phragm) in the master cylinder filler

cover. Position the gasket as shown in

Figs.
40 and 41. Make sure the gasket

is securely seated.

9. Install the cover and gasket on

the master cylinder and secure the

cover into position with the retainer.

DISC BRAKE CALIPER

ALL MODELS EXCEPT

LINCOLN CONTINENTAL

Disassembly

1.
Remove the caliper assembly

from the vehicle as outlined in Section

2.

2.
Remove the caliper locating pins

from the caliper assembly and lift the

anchor plate from the caliper.

3.
Slide the two outer shoe retain-

ing clips off the retaining pins (Fig.

43).

4.
Remove the two retaining pins,

then remove the outer brake shoe

from the caliper.

5.
Slide the inner brake shoe out-

ward until it is free of the hold-down

springs, then remove the brake shoe.

6. Apply air pressure to the fluid

port in the caliper with a rubber

tipped nozzle (Tool 7000-DD) as

shown in Fig. 44 to remove the piston.

Place a cloth over the piston before

applying air pressure to prevent dam-

age to the piston. If the piston is

seized and cannot be forced from the

FIBER

BLOCK

CALIPER

PISTON

H 1574-B

FIG. 44 —Removing Piston From

Caliper —
All
Models Except

Lincoln Continental
caliper, tap lightly around the piston

while applying air pressure. Care

should be taken because the piston

can develop considerable force due to

pressure build-up.

7.
Remove the dust boot from the

caliper assembly.

8. Remove the rubber piston seal

from the cylinder and discard it.

Cleaning and Inspection

Clean all metal parts with isopropyl

alcohol or a suitable solvent. Use

clean, dry, compressed air to clean out

and dry the grooves and passage ways.

Be sure that the caliper bore and com-

ponent parts are completely free of

any foreign material.

Check the cylinder bore and piston

for damage or excessive wear. Replace

the piston if it is pitted, scored, or the

chrome plating is worn off.

Assembly

1.
Apply a film of clean brake fluid

to the new caliper piston seal and in-

stall it in the cylinder bore. Be sure

the seal does not become twisted and

that it is seated fully in the groove.

2.
Install a new dust boot by setting

the flange squarely in the outer groove

of the caliper bore.

3.
Coat the piston with the speci-

fied fluid and install the piston in the

cylinder bore. Spread the dust boot

over the piston as it is installed. Seat

the dust boot in the piston groove.

4.
Position the inner brake shoe so

that the ears of the shoe rests on the

top of the anchor plate bosses and be-

neath the hold-down springs.

5.
Install new caliper locating pin

insulators in the anchor plate.

6. Position the caliper on the an-

chor plate.

7.
Apply water or isopropyl alcohol

to the caliper locating pins and install

them loosely in the anchor plate. Be

sure the guide pins are free of oil,

grease or dirt.

8. Install the caliper on the spindle

as outlined under Disc Brake Caliper

Assembly.

LINCOLN CONTINENTAL

Disassembly

Do not remove the bridge bolts that

hold the two halves of the caliper to-

gether. The two caliper housings are

shown separated in Fig. 46 for illus-

tration purposes only.
1.
Remove the caliper assembly

from the car as outlined in Section 2.

2.
Remove the two attaching bolts

and the caliper splash shield (Fig. 46).

3.
Remove the two shoe and lining

assemblies.

4.
Remove the flexible brake hose

from the caliper.

5.
Remove the external transfer

tube.

6. Remove the four dust boots from

the caliper housings and piston

grooves.

7.
Clamp the caliper in a vise and

secure it by the mounting flanges on

the inboard housing (Fig. 45).

8. Remove the four pistons from

the cylinder bores with the special tool

shown in Fig. 45. To prevent cocking

with consequent damage to the piston

or bore, rotate the piston with the tool

while pulling it outward at the same

time.
Be careful to avoid scratching or

damaging the outside diameter surface

or dust boot retaining groove of the

piston. Such damage causes poor seal-

ing.

If a piston is so completely seized in

the cylinder bore that it can not be re-

moved with the special tool, the cali-

per housing must be replaced, by posi-

tioning two screwdrivers in the piston

dust boot retaining groove and prying

outward. To prevent cocking, tap the

end of the piston lightly around the

circumference with a hammer, while

the prying force is being applied. Be

careful to avoid damaging the dust

boot retainer in the caliper housing

(Fig. 46). If this method of removal is

used, the pistons must be replaced.

If the caliper dust boot retainer or

retaining groove is damaged or

scratched, pry the retainer out of the

caliper housing with screwdrivers.

Too/-T65P-2
J
18- A

H 1652-A

FIG. 45—Removing or Installing

Pistons —
Lincoln
Continentalprocarmanuals.com

02-03-02
Specifications

02-03-02

BORE DIAMETERS-BRAKE DRUM, WHEEL CYLINDER AND MASTER

Models

Ford,

Mercury

and

Meteor

Mont ego

and

Fairlane

Falcon

Mustang

and Cougar

Thunderbird

Continental Mark
III

Lincoln Continental
Taxi and Station Wagon

Other

Pass, except Conv. 250, 302 CID Engines

Pass, and Conv. 351, 390, 428 CID Eng.

Convertible 250, 302 CID Engines

Station and Ranchero

9 Inch Brake
-
Passenger Car

10 Inch Brake
•
Station Wagon

10 Inch Brake
•
Passenger Car

200 CID Engine

351,
390, 428 CID Engine

250,
302, CID Engine
CYLINDER

Brake Drum

Inside

Diameter

11.030

11.030

10.000

10.000

10.000

10.000

9.000

10.000

10.000

9.000

10.000

10.000

11.030

11.030

11.090
Boring Umit

(Max.)
®

11.090

11.090

10.060

10.060

10.060

10.060

9.060

10.060

10.060

9.060

10.060

10.060

11.090

11.090

11.130
Wheel Cylinder Bore Dia.

Front
0

1.094

L_ U25

1.125

1.094

1.094

1.094

1.062
0

1.094

1.125

1.062
®

1.094

1.125

N/A

N/A

N/A
Rear
®

0.938

0.938

0.875

0.875

0.875

0.938

0.844®

0.938

0.875

0.844®

0.875

0.875

0.938

0.938

0.938
Master Cylinder Bore Dia.

With Power

Brake
®

1.000

1.000

0.9375

0.9375

0.9375

0.9375

0.9375

0.9375

0.9375

1.000

1.000

1.000

1.000

1.000

1.000
Less Power

Brake
®

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

1.000

N/A

N/A

N/A

©Max. Runout
0.007

(DMax. Allowable Hone
0.003

CD2.755 For
Ford,
Mercury, Meteor with Disc Brakes.

2.381 For Fairlane, Montego, Falcon, Mustang, Cougar with Disc Brakes.

SHOE AND LINING DIMENSIONS-

DISC BRAKES-INCHES
® Front Wheel Cylinder cannot be honed on Falcon or Mustang with
9
inch Brakes.

Lining Material

Lining Size

Lining Area
-
Square Inches

per Segment

Lining Thickness • Nominal

Lining Wear Limit (Front

Surface
of
Shoe)
•
Max.

Lining Taper -Max.

Lining to Rotor Clearance

(Brakes Released)
Ford,
Mercury, Meteor

Thunderbird, Continen-

tal Mark
III

Bonded

7.38x2.27
Outer

5.36x2.03
Inner

12.25 Outer

8.44 Inner

0.394

0.030

0.125

0.000-0.010
Fairlane, Montego

Falcon,
Mustang,

Cougar

Bonded

6.82 x 1.80 Outer

4.90x1.84 Inner

11.30 Outer

8.80 Inner

0.333
Outer

0.362
Inner

0.030

0.125

0.000
• 0.010
Lining Material

Lining Size

Lining Area

Shoe and Lining Thickness

Lining Thickness

Shoe and Lining Maximum

Wear Limit

Lining Maximum Wear Limit

(from front surface
of
shoe)

Lining to Rotor Clearance

(brakes released)
Lincoln Continental

Riveted Fomoco

5.36x1.90

10.03 Sq. In/segment

0.600
nominal

0.436
nominal

0.231

0.066

0.000-0.010

CALIPER CYLINDER BORE DIAMETER -INCHES

TORQUE LIMITS-HUB TO SPINDLE

Ford,
Mercury, Meteor, Thunderbird, Continental Mark

2.755

Mustang, Cougar, Falcon, Fairlane and Montego

2.381

Lincoln Continental

1.938

ROTOR DIMENSIONS

Car Line

Ford,
Mercury, Meteor

Thunderbird, Continental Mark
III

Fairlane, Falcon, Montego, Mustang

and Cougar

Lincoln Continental
Norn.

Thickness

1.180

1.180

0.935

1.240
Diameter

Outside

11.72

11.72

11.29

11.960
Inside

7.785

7.785

7.355

7.785
Description

Hub and Drum or Rotor Assembly to

Front Wheel Spindle
Ft-Lbs

Rotate
hub
while torquing

to 17-25 ft-lbs. Backoff

the adjusting nut 1/2 turn

and retighten to 10-15

inch pounds while rotat-

ing wheel Selectively
posi-

tion
nut
retainer
on ad-

justing nut
so
that a set

of slots are in line with

cotter pin hole. Adjusting

nut should not be rotated

in this operation. Lock
ad-

justing nut and nut retain-

er with cotter pin so that

the cotter
pin end
does

not interfere with seating

of wheel static collector

in spindle hole.procarmanuals.com

03-01-03
Suspension — Steering, Wheels And Tires — General Service

03-01-03

4.
Connect a tachometer, start the

engine and operate it at idle speed

until the reservoir fluid temperature

reaches 165 to 175. This temperature

must be maintained throughout the

test. Valve B may be partially closed

to create a back pressure up to 350

psi to hasten the temperature rise. The

reservoir fluid must be at the proper

level.

5.
With the engine operating at rec-

ommended idle rpm and fluid temper-

ature noted in Step 4, close the manu-

al valve B. The minimum acceptable

pressure reading is 620 psi.

6. If the pressure gauge reading is

below the minimum specification, the

pump is at fault and should be re-

paired with necessary parts.

7.
If the reading is at or above the

minimum specification, the pump flow

is normal. Open manual valve B and

proceed to the Pump Fluid Pressure

Test.

PUMP FLUID

PRESSURE TEST

1.
Keep the lines and tools con-

nected as in the Pump Flow Test.

2.
With manual valves A and B

opened fully, operate the engine at

recommended idle speed (Fig. 2).

Close manual valve A, then manual

valve B. Do not keep both valves

closed for more than 5 seconds as this

would abnormally increase the fluid

temperature and cause undue pump

and/or gear wear.

3.
With the valves fully closed, the

pressure gauge should read 1000 psi

minimum for Ford, Mercury, Meteor

or Thunderbird and 750 psi minimum

for Cougar, Fairlane, Falcon, Monte-

go or Mustang.

4.
If the pressure gauge reading is

below the minimum specification, the

pump is at fault and should be re-

paired with necessary parts.

5.
If the pressure gauge reading is

at or above the minimum specifica-

tions,
the pump is normal and the

power steering gear or power assist

control valve is at fault.

FLUID PRESSURE TEST-

LINCOLN CONTINENTAL AND

CONTINENTAL MARK III

The pressure testing gauge set, tool

T56L-33610-D, requires modification

to make it adaptable for installation

in the power steering hydraulic sys-

tem. The parts required and the modi-

fication procedure are as follows:
OWER STEERING

PRESSURE LINE

INVERTED FLARE

CONNECTOR

%* TUBE x VA" PIPE

FLARED FEMALE COUPW

%' TUBE x VA" PIPE

G1544.A

FIG. 3—Modified Pressure Gauge

Assembly

a. Power Steering Pressure Line

(refer to the appropriate Parts Catal-

og).

b.
Inverted Flare Connector (3/8

inch OD Tube x 1/4 inch Pipe

Thread).

c. Inverted Flare Connector (5/16

inch OD Tube x 1/4 inch Pipe

Thread).

d. Flared Tube Female Coupling

(3/8 inch OD Tube x 1/4 inch Pipe

Thread).

The connectors and the coupling are

standard-type fittings and can be pur-

chased locally.

e. To modify tool T56L-33610-D,

remove the hose from the hand shut-

off valve block. Install the 3/8 inch x

1/4 inch inverted flare connector in

the valve block, and assemble the

pressure line to the connector (Fig. 3).

Assemble the 3/8 x 1/4 inch coupling

and the 5/16-inch connector to the

free end of the hose leading to the.

pressure gauge.

1.
To check the pump pressure, dis-

connect the front and rear sections of

the pressure line over the number 6

cylinder. Connect the modified pres-

sure-testing gauge assembly, tool

T56L-3361O-D, between the two sec-

tions.

2.
Make sure the hand-valve at the

gauge is fully opened. Start the engine

and cycle the steering gear from stop

to stop to warm up the fluid. Check

the fluid level in the reservoir and add

fluid, if necessary.

3.
Turn the steering wheel to the

full right and full left turn positions

and observe the gauge readings.

Hold the wheels in this position

only long enough to obtain an accu-

rate reading. Do not exceed 5 seconds.

The gauge should read between

1120 and 1250 psi. If the pressure is
less than 1120 psi, close the valve at

the gauge and note the pump pressure.

If it is low with the valve closed, it in-

dicates that the pump is not operating

properly. If the pressure goes up with

the valve closed, it indicates that the

low pressure in the system must be

due to internal leakage in the power

unit, providing all connections are

tight.

4.
Remove the pressure testing

gauge set, and connect the pressure

line at the steering gear. Fill and bleed

the system.

FRONT WHEEL ALIGNMENT

CHECKS

Do not attempt to check and adjust

front wheel alignment without first

making a preliminary inspection of

the front-end parts. Refer to Section

3.

Check all the factors of front wheel

alignment except the turning angle

before making any adjustments. The

turning angle should be checked only

after caster, camber, and toe-in have

been adjusted to specifications.

The front wheel alignment specifica-

tions given in Part 3-13, are correct

only when the vehicle is at curb load.

Before checking or adjusting the

alignment factors, the suspension

alignment spacers must be installed to

obtain the curb Height.

EQUIPMENT INSTALLATION

Equipment used for front wheel

alignment inspection must be accu-

rate.
Whenever possible, front wheel

alignment checks should be performed

on stationary wheel aligning equip-

Too/
- T65P3000-A or S

FIG. 4—Typical Front Alignment

Spacer Installation—Cougar,

Fairlane, Falcon,
Montego,
Mustangprocarmanuals.com

03-01-06
Suspension — Steering, Wheels And Tires — General Service

03-01-06

SUSPENSION UPPER

ARM MOVEMENT

Front Bolt Outboard

Rear Bolt Outboard

Front Bolt Inboard

Rear Bolt Inboard
CASTER CHANGE

Tilt Backward

Increase Positive Caster

or

Decrease Negative Caster

Tilt Forward

Decrease Positive Caster

or

Increase Negative Caster

Tilt Forward

Decrease Positive Caster

or

Increase Negative Caster

Tilt Backward

Increase Positive Caster

or

Decrease Negative Caster
CAMBER CHANGE

Tilt Outward

Increase Positive Camber

or

Decrease Negative Camber

Tilt Inward

Decrease Positive Camber

or

Increase Negative Camber

FIG. 14—Caster and Camber Adjustments

sary. Then, tighten the upper arm

inner shaft attaching bolts to specifi-

cation. Remove the adjusting bar

(Tool T65P-3OOO-D) and the align-

ment spacers (Tool T65P-3O00-E or

F).

Camber

To adjust the camber angle, install

the tool as outlined above (Fig. 13).

Loosen both inner shaft attaching

bolts and tighten or loosen the hook

nuts to move the inner shaft inboard

or outboard as necessary with Tool

T65P-3OOO-D to increase or decrease

camber (Fig. 13). The camber angle

can be checked without tightening the

inner shaft attaching bolts.

COUGAR, FAIRLANE, FALCON,

MONTEGO, MUSTANG

Be sure all the equipment listed in

Equipment Installation is installed be-

fore adjusting the caster and camber.

Caster is controlled by the front

suspension strut (Fig. 15). To obtain

positive caster, loosen the strut rear

nut and tighten the strut front nut

against the bushing. To obtain nega-

tive caster, loosen the strut front nut

and tighten the strut rear nut against

the bushing.

Camber is controlled by the eccen-

tric cam located at the lower arm at-

tachment to the side rail (Fig. 13).

To adjust the camber, loosen the

camber adjustment bolt nut at the

rear of the body bracket. Spread the

body bracket at the camber adjust-
TER ADJUSTMENT NUTS

EAR INSULATOR

WASHER
FRONT ADJUSTMENT NUT

INNER SLEEVE

TURN NUTS

REARWARD

TO OBTAIN

POSITIVE

CASTER
OUTER SLEEVE

RONT INSULATOR

WASHER

CASTELLATED

NUT

TURN NUTS

FORWARD

TO OBTAIN

NEGATIVE

CASTER

NEGATIVE

CAMBER

SPREAD THIS MEMBER AT

LOWER ARM PIVOT

BUSHING

PRY AT THESE POINTS'

F1371-A

FIG. J5—Caster and Camber Adjustments

ment bolt area just enough to permit

lateral travel of the arm when the ad-

justment bolt is turned. Rotate the

bolt and eccentric clockwise from the

high position to increase camber or

counterclockwise to decrease camber.

After the caster and camber has

been adjusted to specification, torque

the lower arm eccentric bolt nut and

the strut front nut to specification.
LINCOLN CONTINENTAL

Preliminary Steps

1.
With the car properly positioned

and wheel alignment measuring equip-

ment properly installed, raise the hood

and scribe chalk marks around the

bolts and lock washers that secure theprocarmanuals.com

03-02-09
Suspension

03-02-09

WOOD BLOCK
F
1287-A

FIG. 9—Upper
Arm
Support—

Montego, Falcon
and
Fairlane

Tool-T62F-3006-A

ARM SUPPORT

LOWER BALL JOINT
SLEEVE

Too/-T57P-3006-A

F 1157-C

FIG. TO—Loosening Ball Joint

Studs
in
Spindle—Typical

from
the
spindle.
Do not
loosen
the

stud with tool pressure alone. Raise

the stud
out of the
spindle bore.

6. Using
a
large chisel,
cut off the

three upper ball joint retaining rivets

and remove
the
ball joint.

7.
Clean
the end of the arm, and

remove
all
burrs from
the
hole edges.

Check
for
cracks
in the
metal
at the

holes,
and
replace
the arm if it is

cracked.

8. Attach
the new
ball joint
to the

upper
arm. Use
only
the
specified

bolts,
nuts,
and
washers.
Do not
rivet

the
new
ball joint
to the
arm. Torque

the nuts
to
specification (Part 3-13).

9. Position
the
lower ball joint stud

in
the
spindle bore,
and
torque
the at-

taching
nut to
specification. Install
a

new cotter
pin and
tighten
the nut if

necessary
to
line
up the
cotter
pin

hole.
Install
a new
cotter
pin in the

lower ball joint
if it was
removed.
1495-A

FIG. 11 —Shaft Centered
in

Arm—Typical

F 1494- A

FIG. 12—Torque Upper
Arm

Inner Shaft Bushings—Typical

10.
Lubricate
the
ball joint,
and in-

stall
the
wheel
and
tire. Torque
the

lug nuts
to
specification (Part 3-13).

11.
Remove
the
safety stands,
and

lower
the
vehicle.

12.
Remove
the
support from
be-

tween
the
upper
arm and
frame.

13.
Check
and, if
necessary, adjust

caster, camber,
and
toe-in.

UPPER ARM SHAFT AND/OR

BUSHING REPLACEMENT

COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

1.
Remove
the
shock absorber
and

upper mounting bracket
as an
assem-

bly.

2.
Raise
the
vehicle
on a
hoist,
in-

stall safety stands,
and
remove
the

wheel cover
or hub cap.

3.
Remove
the
grease
cap
from
the

hub;
then, remove
the
cotter
pin, nut

lock, adjusting
nut and
outer bearing

from
the hub.

4.
Pull
the
wheel, tire,
and the hub

and drum
off the
spindle
as an
assem-

bly.
5.
Install
the
spring compressor

tool (Figs.
20, 21 and 22).

6. Remove
2
upper arm-to-spring

tower attaching nuts
and
swing
the

upper
arm
outboard from
the
spring

tower.

7.
Rotate
the
inner shaft
so
that
the

studs
can be
removed. Remove
the

studs with
a
soft mallet.

8. Unscrew
the
bushings from
the

shaft
and
suspension
arm;
then,
re-

move
the
shaft from
the arm.

9. Position
the
shaft
in the. arm,

apply grease
to the new
bushings
and

O-rings,
and
install
the
bushings loose

on
the
shaft
and
arm. Turn
the
bush-

ings
so
that
the
shaft
is
exactly
cen-

tered.
The
shaft will
be
properly
cen-

tered when dimensions
A and B in

Fig.
11 are
equal.

10.
Fabricate
a
spacer from
a sec-

tion
of
3/4-inch diameter pipe
or

metal
of
comparable size
and

strength.
The
spacer should
be 6

15/16 inches long.

11.
Position
the
spacer parallel with

the inner shaft,
and
force
the
spacer

between
the
flanges
of the
upper
arm

(Fig.
12).

If
the
spacer cannot
be
forced
be-

tween
the arm
flanges due
to
excessive

distortion, replace
the
upper
arm as-

sembly.

12.
With
the
spacer positioned
in

the
arm,
torque
the
bushings
to
speci-

fication. Move
the arm on the
shaft
to

be sure that
no
binding exists, then
re-

move
the
spacer.

13.
Attach
the
suspension upper

arm
to the
underbody. Release
the

front spring.

14.
Remove
the
spring compressor

and position
the
wheel, tire,
and hub

and drum
on the
spindle.

15.
Install
the
bearing, washer,
ad-

justing
nut and nut
lock. Adjust
the

wheel bearing
as
outlined
in
Part
3-12

and install
the
cotter
pin,
grease
cap

and
hub cap or
wheel cover.

16.
Lower
the
vehicle
and
install

the shock absorber
and
upper mount-

ing bracket.

17.
Check caster, camber,
and toe-

in,
and
adjust
as
necessary (Part 3-1).

LOWER BALL JOINT

REPLACEMENT-

ARM
IN
VEHICLE

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK
III

1.
Raise
the
vehicle high enough
to

provide working space, leaving
theprocarmanuals.com

03-02-13

Suspension

03-02-13

BALL JOINT BOLT HEAD

STABILIZER

F1370-A

FIG. 18 —Removing or Installing Front Spring

TURN TO COMPRESS

NUT
•

Tool T 63 P-53J0-A

SHAFT SCREW

Lower Adapter Plate

CAVITY
Upper Adapter Plate

T67P-5370-A

FIG. 79—Spring Tool Installation

through the lower arm. Install and

torque the nut to specification.

3.
Secure the lower end of the

shock absorber to the lower arm with

the two attaching bolts.

4.
Secure the strut and the rebound

bumper to the lower arm with the two
F
1492.
A

attaching bolts. Torque the bolts to

specification

5.
Connect the sway bar to the

lower arm with the attaching washer

and insulators as shown in Fig. 1.

Torque the nut to specification.

6. Check the front end alignment
and adjust it to the recommended

specifications if required.

COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Removal

1.
Remove the shock absorber and

upper mounting bracket as an assem-

bly.

2.
Raise the vehicle on a hoist, in-

stall safety stands, and remove the

wheel cover or hub cap.

3.
Remove the grease cap from the

hub;
then, remove the cotter pin, nut

lock, adjusting nut and outer bearing

from the hub.

4.
Pull the wheel, tire and the hub

and drum off the spindle as an assem-

bly.

5.
Install the spring compressor

tool as shown in Figs. 19, 20 and 21.

6. Remove 2 upper arm-to-spring

tower attaching nuts and swing the

upper arm outboard from the spring

tower (Fig. 21).

7.
Release the spring compressor

tool and remove the tool from the

spring. Then, remove the spring from

the vehicle.

Installation

1.
Place the spring upper insulator

on the spring and secure in place with

tape.

2.
Position the spring in the spring

tower. Install the spring compressor,

(Fig. 19) and compress the spring.

3.
Swing the upper arm inboard

and insert the bolts through the holes

in the side of the spring tower. Then,

install the attaching nuts and torque

them to specification.

4.
Release the spring pressure and

guide the spring into the upper arm

spring seat. The end o! the spring

must seat against the tab on the

spring seat.

5. Remove the spring compressor

and position the wheel, tire, and hub

and drum on the spindle.

6. Install the bearing, washer, ad-

justing nut and lock nut. Adjust the

wheel bearing as outlined in Part 3-12

and install the cotter pin, grease cap,

and hub cap or wheel cover.

7.
Lower the vehicle and install the

shock absorber and upper mounting

bracket.

8. Check caster, camber, and toe-in

and adjust as necessary (Part 3-1).procarmanuals.com

03-02-15

Suspension

03-02-15

BUSHING

BUSHING

WASHER

BOLT
K5s»

LOCKWASHER

STRUT

NUT
;Y'0lT-£ii *

' N
WASHER
>*V ©"*

LOCKWASHER #

NUT
SHER/
©^—
SLOWER
ARM
ASSY.

«
^PLUG

INSULATOR

WASHER

NUT

NUT

F1221-B

FIG. 22—Front Suspension Componentsprocarmanuals.com

03-02-18
Suspension

03-02-18

5.
Remove the cotter pin from the

upper ball joint stud nut.

6. Loosen the upper ball joint stud

nut one or two turns. Do not remove

the nut from the stud at this time.

7.
Install tool T57P-3006-A be-

tween the upper and lower ball joint

studs with the adapter screw on top

(Fig. 13). The tool should be seated

firmly against the ends of both studs

and not against the nuts or lower stud

cotter pin.

8. With a wrench, turn the adapter

screw until the tool places the stua

under tension. Tap the spindle near

the upper stud with a hammer to loos-

en the stud in the spindle. Do not

loosen the stud from the spindle with

tool pressure only.

9. Remove the tool from between

the ball joint studs and place a floor

jack under the lower arm.

10.
Raise the floor jack to relieve

the pressure from the upper ball joint

stud nut and remove the nut.

11.
Remove the upper arm inner

shaft attaching bolts. Remove the

upper arm and inner shaft as an as-

sembly (Fig. 1).

12.
Remove the bumpei from the

upper arm.

Installation

1.
Position the bumper to the upper

arm and install the nut and washer.

Torque the nut to specifications.

2.
Position the upper arm inner

shaft to the frame side rail and install

the 2 attaching bolts and washers

snug.

3.
Connect the upper ball joint stud

to the spindle and install the attaching

nut. Torque the nut to specification

and continue to tighten the nut until

the cotter pin hole in the stud is in

line with the nut slots. Then, install

the cotter pin.

4.
If equipped with drum type bra-

kes—Adjust the brakes as outlined in

Part 2-2. Install the wheel, tire, and

drum to the spindle and adjust the

wheel bearings as outlined in Part

3-12.

5.
If equipped with disc brak-

es—Install the wheel and tire on the

hub and adjust the wheel bearings as

outlined in Part 3-12.

6. Install the hub cap or wheel

cover.

7.
Remove the safety stands and

lower the front of the vehicle.

8. Check caster, camber, and toe-in

and adjust as required (Section 2, Part

3-D.
COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Removal

1.
Raise the front of the vehicle,

position safety stands under the

frame, and lower the vehicle slightly.

2.
Remove the wheel and tire.

3.
Remove the shock absorber

lower attaching nuts and washers.

4.
Remove the shock absorber

upper mounting bracket attaching

nuts,
and remove the shock absorber

and bracket as an assembly (Fig. 26).

On all 8-cylinder vehicles, remove

the air cleaner to obtain access for

tool installation.

5.
Install the spring compressor

tool and compress the spring (Figs.

19,
20 and 21).

6. Position a safety stand under the

lower arm.

7.
Remove the cotter pin from the

nut on the upper ball joint stud, and

loosen the nut one or two turns. Do

not remove the nut from the stud at

this time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs as shown in Fig. 10. The

tool should seat firmly against the

ends of both studs and not against the

stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension; then, hit the spindle

smartly near the upper stud with a

hammer to break the stud loose in the

spindle. Do not loosen the stud in the

spindle with tool pressure only. If

both arms are being removed, loosen

the lower stud in the same manner as

the upper stud.

10.
Remove the nut from the upper

stud and lift the stud out of the

spindle.

11.
Remove the upper arm inner

shaft attaching nuts from the engine

compartment, and remove the upper

arm.

12.
Wipe off all loose dirt from the

upper arm parts. Do not wash the ball

joint with a solvent.

Installation

1.
Position the upper arm on the

underbody mounting bracket, and in-

stall the nuts and lock washers on the

two inner shaft attaching bolts. The

specified keystone-type lock washers

must be used. Torque the nuts to

soecification.
2.
Position the upper ball joint stud

in the top of the wheel spindle, and in-

stall the stud nut. Torque the nut to

specification, and continue to tighten

it until the cotter pin hole and slots

line up. Install a new cotter pin.

3.
Release the coil spring, remove

the tool, and install the front shock

absorber and the wheel and tire.

LINCOLN CONTINENTAL

Removal

1.
Place a jack under the outer end

of the suspension lower arm and raise

the arm. Refer to Fig. 22.

2.
Remove the wheel and tire.

3.
Remove the cotter pin from the

upper ball joint stud. Loosen the nut

one or two turns.

4.
Place a box wrench over the

lower end of the ball joint remover

tool, and position the tool as in Fig.

13.
The tool should seat firmly against

the ends of both studs, and not

against the upper stud nut.

5.
Turn the wrench until both studs

are under tension, and then, tap the

spindle with a hammer near the upper

stud to loosen it from the spindle. Do

not loosen the stud with tool pressure

alone. Remove the nut.

UPPER MOUNTING BRACKET

LOWER RETAINING BOLTS F 1490-A

FIG. 26—Removing or Installing

Front Shock Absorber—Typicalprocarmanuals.com

03-02-19

Suspension

03-02-19

6. Raise the upper arm to free the

ball joint stud from the spindle. Wire

the upper end of the spindle to the un-

derbody to prevent damage to the

brake hose.

7.
Mark the position of the upper

arm shaft on the underbody member

to facilitate making caster and camber

adjustments after installation of the

upper arm.

8. Remove the suspension upper

arm-to-underbody attaching bolts,

lock washers, and attaching nuts.

Then, remove the upper arm.

Installation

1.
Position the upper arm shaft on

the underbody member. Line up the

shaft with the marks made before re-

moval of the arm.

2.
Install the attaching bolts and

lock washers. FABRICATE A

TOOL, AS SHOWN IN Fig. 27, to

hold the nut in place while starting the

attaching bolt into the nut. Remove

the tool; then, tighten the attaching

bolts to specification.

3.
Guide the ball joint stud into the

spindle. Install the attaching nut and

torque it to specification. Continue

tightening the nut to line up the cotter

pin hole. Install a new cotter pin.

4.
Install the wheel and tire, and

torque the wheel lug nuts to specifica-

tion.

5.
With the front end weight of the

car on the wheels, torque the bolts at

the ends of the upper arm shaft to

specification if the bushings were re-

placed.

6. Check the front wheel alignment.

FRONT WHEEL SPINDLE

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK III

Removal

1.
Raise the vehicle until the front

wheel clears the floor, and place a

support under the frame.

2.
Remove the hub cap or wheel

cover.

3.
If equipped with drum type

brakes—remove the wheel and tire

and brake drum as an assembly (Part

3-12). Remove the brake backing

plate attaching bolts and remove the

backing plate from the spindle. Wire

the backing plate to the underbody to

prevent damage to the brake hose.
1/16" GAUGE
-*.

STEEL (REFERENCE)

—3/16'
3/8'

1/2" DIAMETER PLUG WELD

F 1501-A

FIG. 27 -Upper Arm Shaft Installing Tool

4.
If equipped with disc brakes—re-

move the wheel and tire from the hub.

Remove 2 bolts and washers retaining

the caliper and brake hose to the

spindle. Remove the caliper from the

rotor and wire it to the underbody to

prevent damage to the brake hose.

Then, remove the hub and rotor from

the spindle (Part 3-12). Remove 3

bolts attaching the splash shield to the

spindle and remove the splash shield.

5.
Remove the steering connecting

rod from the spindle arm with tool

OTC462.

6. Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

7.
Install the ball joint remover tool

between the upper and lower ball joint

studs (Fig. 7). The tool sho.uld seat

firmly against the ends of both studs

and not against the stud nuts.

8. Turn the tool nut with a wrench

until the tool places the studs under

tension, and, with a hammer, tap the

spindle near the stud to loosen them

in the spindle. Do not loosen the studs

in the spindle with tool pressure only.

9. Position a floor jack under the

lower control arm.

10.
Remove the ball joint stud nuts

and lower the lower arm enough to re-

move the spring and the spindle.
Installation

1.
Position the spindle to the lower

ball joint stud and install the attaching

nut. Torque the nut to specification.

Continue to tighten the nut until the

cotter pin hole is in line with the slots

in the nut. Then, install the cotter pin.

2.
Position the spring and raise the

lower arm and guide and upper ball

joint stud into the spindle hole and in-

stall the attaching nut. Torque the nut

to specification and install the cotter

pin as outlined in the preceeding step.

3.
Remove the floor jack from

under the lower arm.

4.
Attach the steering connecting

rod to the spindle and install the nut.

Torque the nut to specification. Con-

tinue to tighten the nut until the cotter

pin hole is in line with the slots in the

nut. Then, install the cotter pin.

5.
If equipped with drum type

brakes—Position the brake backing

plate to the spindle and install the at-

taching bolts. Torque the bolts to spe-

cification. Adjust the brakes as out-

lined in Part 2-2. Install the wheel,

tire,
and drum to the spindle and ad-

just the wheel bearings as outlined in

Part 3-12).

6. If equipped with disc brak-

es—Install the splash shield on the

spindle and torque the attaching bolts

to specification (Part 3-13). Install theprocarmanuals.com