tow FORD MUSTANG 1969 Volume One Chassis

07-03-28
FMX Transmission

07-03-28

CENTER

SUPPORT
ROTATE

CARRIER

COUNTER

CLOCKWISE

SAWTEETH IN

CLOCKWISE

DIRECTION

MOVE ROLLER

TOWARD CENTER

D 1291-D

FIG. 56—Planetary Clutch Installation in Carrier—Center Support

Not Chamfered
er between the large internal gear and

the transmission case. Note the indi-

cator reading. End play should be

0.010-0.029 inch (minimum end play

is preferred).

4.
Remove the indicator and the

tool from the extension housing.

5.
Install the one remaining front

pump attaching bolt and torque it to

specification.

FRONT SERVO

1.
Position the front band forward

in the case with the band ends up.

2.
Position the servo strut with the

slotted end aligned with the servo act-

uating lever, and with the small end

aligned with the band end. Rotate the

band, strut, and servo into position

engaging the anchor end of the band

with the anchor pin in the case.

3.
Locate the servo on the case, and

install the attaching bolts. Tighten the

attaching bolts only two or three

threads.

4.
Install the servo release tube.

REAR SERVO

12.
Install the output shaft, careful-

ly meshing the internal gear with the

pinions.

REAR SUPPORT

1.
Position the needle bearing and

retainer on the rear support (Fig. 24).

2.
Position a new rear support to

case gasket on the rear support. Re-

tain the gasket with transmission

fluid.

3.
Install the rear support. As the

support is installed, insert the tubes

into the case.

GOVERNOR

1.
Position the governor drive ball

in the pocket in the output shaft. Re-

tain the ball with transmission fluid.

2.
Install the governor assembly, al-

igning the groove with the ball in the

output shaft.

3.
Install the governor with the gov-

ernor body plate toward the front of

the vehicle (Fig. 23). Install the gover-

nor snap ring

EXTENSION HOUSING

1.
Insert the extension housing oil

seal re placer and pilot in the housing.

Position a new gasket to the extension

housing and install the extension

housing on the transmission case.

Coat the bolt threads with B5A-
19554-A sealer and install the exten-

sion housing attaching bolts, breather

tube clip, vacuum tube clip, and exter-

nal tooth lock washer. The lock wash-

ers must be installed with the rolled

edge toward the transmission case to

insure a tight seal.

2.
Torque the extension housing at-

taching bolts to specification.

3.
Install the lubrication tube.

FRONT PUMP

1.
Position a new front pump gask-

et in the counterbore of the transmis-

sion case.

2.
Install the front pump, aligning

the pump bolt holes with the holes in

the case. Install three of the front

pump attaching bolts and torque them

to specification.

TRANSMISSION END

PLAY CHECK

1.
Mount the dial indicator support

in a front pump bolt hole. Mount a

dial indicator on the support so that

the contact rests on the end of the tur-

bine shaft.

2.
Use a large screwdriver to pry

the front of the clutch drum toward

the rear of the transmission. Set the

dial indicator at zero.

3.
Remove the screwdriver and pry

the units toward the front of the

transmission by inserting a screwdriv-
1.
Position the servo anchor strut,

and rotate the rear band to engage the

strut.

2.
Position the servo actuating lever

strut with a finger, and then install the

servo and attaching bolts. Torque the

bolts to specification.

3.
Install the front servo apply

tube.

PRESSURE REGULATOR

BODY

1.
Install the pressure regulator

body and attaching bolts, and torque

the bolts to specifications.

2.
Install the control and converter

valve guides and springs. Install the

spring retainer.

CONTROL VALVE BODY

1.
Install the control valve assem-

bly, carefully aligning the servo tubes

with the control valve. Align the inner

downshift lever between the stop and

the downshift valve. Shift the manual

lever to the 1 position. Align the man-

ual valve with the actuating pin in the

manual detent lever. Do not tighten

the attaching bolts.

2.
Move the control valve body

toward the center of the case until the

clearance is less than 0.050 inch be-

tween the manual valve and the act-

uating pin on the manual detent lever.

3.
Torque the attaching bolts toprocarmanuals.com

07-04-14
C-6 Automatic Transmission
07-04-14

taching bolt to turn the converter to

gain access to the nuts.

5.
Remove the rear mount to

crossmember attaching bolt.

6. Remove the two crossmember-

to-frame attaching bolts.

7.
Remove the two engine rear

support-to-extension housing attaching

bolts.

8. Disconnect the downshift rod

from the transmission downshift lever.

9. Disconnect the manual linkage

rod from the lever at the transmission.

On a column shift, use tool T67P-

7341-A to remove the rod.

10.
Remove the two bolts securing

the bellcrank bracket to the converter

housing.

11.
Raise the transmission with a

transmission jack to provide clearance

to remove the crossmember.

12.
Remove the rear mount from

the crossmember and remove the

crossmember from the side supports.

13.
Lower the transmission to gain

access to the oil cooler lines.

14.
Disconnect each oil line from

the fittings on the transmission.

15.
Disconnect the vacuum line

from the diaphragm located at the

right rear of the transmission. Remove

the metal line from the retaining clip

on the transmission.

16.
Disconnect the speedometer

cable from the extension housing.

17.
Remove the bolt that secures

the transmission fluid filler tube to the

cylinder block. Lift the filler tube and

the dipstick from the transmission.

18.
Secure the transmission to the

jack with the chain.

19.
Remove the converter housing-

to-cylinder block attaching bolts.

20.
Carefully move the transmission

away from the engine and, at the

same time, lower it to clear the und-

erside of the vehicle.

21.
Remove the converter and

mount the transmission in a holding

fixture.

INSTALLATION—FORD

MERCURY AND METEOR

1.
Torque the two converter drain

plugs to specification.

2.
Install the converter on the sta-

tor support.

3.
Secure the transmission to the

jack with the chain.

4.
Rotate the flywheel to place two

converter mounting stud holes that are

adjacent to the drain plug holes in a

vertical position.

5.
Rotate the converter so that the

studs and drain plugs are in alignment

with those in the flywheel.
6. Move the transmission toward

the cylinder block until they are in

contact. Install and torque the attach-

ing bolts to specification making sure

that the vacuum tube retaining clips

are properly positioned.

7.
Remove the transmission jack

chain from around the transmission.

8. Install a new Oring on the lower

end of the transmission filler tube. In-

sert the tube in the transmission case

and secure the tube to the engine with

the attaching bolt.

9. Connect the speedometer cable

to the extension housing.

10.
Connect the oil cooler lines to

the right side of transmission case.

11.
Connect the vacuum line to the

vacuum diaphragm making sure that

the metal tube is secured in the retain-

ing clip.

12.
Position the cross member on

the side supports. Position the rear

mount on the crossmember and install

the attaching bolt and nut.

13.
Secure the engine rear support

to the extension housing and torque

the bolts to specification.

14.
Lower the transmission and re-

move the jack.

15.
Secure the crossmember to the

side supports with the attaching bolts

and torque them to specification.

16.
Position the bellcrank bracket

to the converter housing and install

the two attaching bolts.

17.
Connect the downshift rod to

the transmission downshift lever.

18.
Connect the selector rod to the

manual lever at the transmission. On

a column shift, use tool T67P-7341-A

and install a new grommet in the

manual lever. Then, secure the manual

selector rod to the lever.

19.
Secure the converter-to-flywheel

attaching nuts and torque them to

specification. Use a wrench on the

crankshaft pulley attaching nut to ro-

tate the flywheel. Do not use a wrench

on the converter attaching nuts to ro-

tate it.

20.
Install the converter housing

dust shield and secure it with the at-

taching bolts.

21.
Secure the starter motor in

place with the attaching bolts. Con-

nect the cable to the terminal on the

starter.

22.
Install the driveshaft.

23.
Adjust the shift linkage as de-

tailed in Section 2.

24.
Lower the vehicle.

25.
Fill the transmission to the cor-

rect level with the specified lubricant.

Start the engine and shift the trans-

mission to all ranges, then recheck the

fluid level.
REMOVAL—FAIRLANE,

MONTEGO, MUSTANG

AND COUGAR

1.
On Mustang and Cougar, dis-

connect the neutral switch wires from

the harness connector and the retain-

ing clip on the dash.

2.
Remove the bolt that secures the

filler tube to the rear of the right

cylinder head.

3.
Raise the vehicle on a hoist or

jack stands.

4.
Remove the converter drain plug

access cover from the lower end of the

converter housing.

5.
Place a drain pan under nhe con-

verter housing and remove the two

converter drain plugs. Install the plugs

after the fluid has drained.

6. Place the drain pan under the

transmission fluid pan. Starting at the

rear of the pan and working toward

the front, loosen the attaching bolts

and allow the fluid to drain. Finally

remove all of the pan attaching bolts

except two at the front, to allow the

fluid to further drain. After the fluid

has drained, install two bolts on the

rear side of the pan to temporarily

hold it in place.

7.
Disconnect the drive shaft from

the rear axle flange and remove it

from the transmission. Install tool

T61L-7657-A in the rear of the exten-

sion housing to prevent the fluid from

leaking.

8. Disconnect the downshift rod

from the transmission downshift lever.

9. Disconnect the shift rod from the

manual lever. On a column shift, use

tool T67P-7341-A to remove the rod.

10.
Disconnect the speedometer

cable from the extension housing.

11.
Disconnect the rubber hose

from the vacuum diaphragm at the

rear of the transmission. Remove the

vacuum tube from the retaining clip at

the transmission.

12.
Disconnect the starter cable

from the terminal on the starter. Re-

move the starter attaching bolts and

remove it from the housing.

13.
Lift the fluid filler tube from

the transmission case.

14.
Remove the four converter-

to-flywheel attaching nuts.

15.
On a Mustang or Cougar, dis-

connect the complete exhaust system

and allow it to hang on the rear axle.

16.
Remove the two nuts that at-

tach the engine rear support to the

crossmember.

17.
Raise the transmission with a

jack just enough to remove the weight

from the crossmember.

18.
Remove the cotter pins from

the crossmember-to-frame side sup-procarmanuals.com

07-04-16
C-6 Automatic Transmission

07-04-16

INSTALLATION—

THUNDERBIRD

1.
Torque the two converter drain

plugs to specification.

2.
Install the converter on the sta-

tor support.

3.
Secure the transmission on a

transmission jack.

4.
Rotate the converter so that the

studs and drain plugs are in alignment

with their holes in the flywheel.

5.
Move the transmission toward

the cylinder block until they contact

each other. Install and torque the at-

taching bolts to specification. Before

tightening the center bolt on the left

side,
make sure that the accelerator

linkage stop bracket is properly posi-

tioned so that the left upper bolt may

be installed later.

6. Connect the fluid cooler lines to

their fittings on the right side of the

transmission.

7.
Raise the transmission and in-

stall the engine rear support and tor-

que the bolts to specification. Make

sure that the hand brake equalizer is

positioned properly.

8. Lower the transmission and re-

move the jack.

9. Install the engine rear support-

to-extension housing attaching bolts.

10.
Install the drive shaft.

11.
Connect the speedometer cable

to the extension housing.

12.
Position the starting motor on

the converter housing and secure it

with the two lower bolts.

13.
Install the torque converter-

to-flywheel attaching nuts and torque

them to specification.

14.
Install the converter housing

dust shield.

15.
Secure the frame side rail sup-

port brace with the attaching bolts

and lock washers. Torque the bolts to

specification.

16.
Connect the downshift rod to

the transmission downshift lever.

17.
Connect the vacuum diaphragm

hose to the upper end of the vacuum

tube.

18.
Using Tool T67P-7341-A, in-

stall a new grommet in the manual

lever. Then, secure the manual selec-

tor rod to the lever.

19.
Position the vibration absorber

to the transmission extension housing

and secure it with the three attaching

bolts.

20.
Connect the muffler inlet pipes

to the exhaust manifolds.

21.
Lower the vehicle and install

the two converter housing upper bolts

and torque them to specification.
22.
Install the starting motor upper

bolt.

23.
Place a new O-ring on the end

of the fluid filler tube and insert it in

the transmission case. Secure the tube

to the rear of the right cylinder head

with the attaching screw and lock

washer.

24.
Fill the transmission to the

proper level with the specified fluids.

25.
Adjust the manual and throttle

linkage as required.

REMOVAL-

CONTINENTAL MARK III

1.
Working from the engine com-

partment, lift the fluid filler tube dio-

stick from the transmission.

2.
Raise the vehicle on a hoist or

stands.

3.
Remove the dust shield from the

front lower end of the converter hous-

ing.

4.
Crank the engine until one of the

converter drain plugs is accessible.

Then, remove the plug.

5.
Crank the engine until the other

plug is at the bottom. Place a drain

pan to catch the fluid, then remove

the pan and allow the fluid to drain.

6. Remove the driveshaft.

7.
Remove the frame side rail sup-

port brace attaching bolts and remove

the brace.

8. After the fluid has been drained

from the converter, install the plug.

9. Place the drain pan under the

transmission pan and loosen the at-

taching bolts and allow the fluid to

drain. Finally remove all of the pan

attaching bolts except two, to allow

the oil to further drain. After the fluid

has drained, install two bolts on the

opposite side of the pan to temporari-

ly hold it in place.

10.
Remove the. converter-

to-flywheel attaching nuts.

11.
Disconnect the downshift link-

age from the transmission downshift

lever.

12.
Using tool T67P-7341-A, re-

move the selector rod from the manu-

al lever.

13.
Remove the two screws that at-

tach the shift rod bellcrank bracket to

the converter housing and remove the

bracket.

14.
Disconnect the vacuum dia-

phragm hose at the transmission.

15.
Disconnect the speedometer

cable from the extension housing and

place it to one side.

16.
Remove the two idler arm

bracket retaining bolts at the frame

side rail and allow the linkage to

hang.
17.
Disconnect the starter cable

from the terminal on the starter. Re-

move the starter attaching bolts and

remove it from the housing.

18.
Remove the clip securing the oil

cooler lines to the support bracket.

19.
Disconnect the two oil cooler

lines from the right side of the trans-

mission.

20.
Disconnect the muffler inlet

pipes at the exhaust manifolds and

allow the pipes to hang.

21.
Remove the vibration absorber

from the extension housing.

22.
Remove the engine rear support

to extension housing attaching bolts.

23.
Place a transmission jack under

the transmission and raise it just

enough to remove the weight from the

support.

24.
Remove the two support attach-

ing bolts and remove the support.

25.
Lower the jack and secure the

transmission to the jack with a safety

chain.

26.
Remove the bolt that secures

the filler tube to the rear of the right

cylinder head and lift the tube from

the transmission case.

27.
Remove the six converter

housing-to-cylinder block attaching

bolts.

28.
Carefully lower the transmis-

sion and remove it from under the ve-

hicle.

29.
Remove the converter and

mount the transmission in a holding

fixture.

INSTALLATION—

CONTINENTAL MARK III

1.
Torque the two converter drain

plugs to specification.

2.
Install the converter on the sta-

tor support.

3.
Secure the transmission on a

transmission jack.

4.
Rotate the converter so that the

studs and drain plugs are in alignment

with their holes in the flywheel.

5.
Move the transmission toward

the cylinder block until they contact

each other. Install and torque the at-

taching bolts to specification

6. Remove the jack safety chain

from the transmission.

7.
Connect the fluid cooler lines to

their fittings on the right side of the

transmission.

8. Install a new O-ring on the lower

end of the fluid filler tube. Dip the

O-ring in clean automatic transmis-

sion fluid and insert the tube in the

transmission case. Install the attach-

ing bolt.procarmanuals.com

07-04-17
C-6 Automatic Transmission
07-04-17

9. Raise the transmission and in-

stall the engine rear support and tor-

que the bolts to specification.

10.
Lower the transmission and re-

move the jack.

11.
Install the engine rear support-

to-extension housing attaching bolts.

12.
Install the drive shaft.

13.
Connect the speedometer cable

to the extension housing.

14.
Connect the muffler inlet pipes

to the exhaust manifolds.

15.
Position the starting motor on

the converter housing and secure it

with the attaching bolts. Connect the

cable to the terminal on the starter.

16.
Position the idler arm bracket

to the frame side rail and install the

attaching bolts.

17.
Install the torque converter-

to-flywheel attaching nuts and torque

them to specification.

18.
Install the converter housing

dust shield.

19.
Secure the frame side rail sup-

port brace with the attaching bolts

and lock washers. Torque the bolts to

specification.

20.
Connect the downshift rod to

the transmission downshift lever.

21.
Using Tool T67P-7341-A, in-

stall a new grommet in the manual

lever. Then, secure the manual selec-

tor rod to the lever.

22.
Connect the vacuum hose to the

vacuum diaphragm.

23.
Install the oil cooler line retain-

ing clip at the transmission support.

24.
Position the vibration absorber

to the transmission extension housing

and secure it with the three attaching

bolts.

25.
Lower the vehicle.

26.
Fill the transmission to the

proper level with the specified fluids.

27.
Adjust the manual and throttle

linkage as required.

REMOVAL-

LINCOLN CONTINENTAL

1.
Raise the hood and remove the

transmission dipstick.

2.
Raise the vehicle on a hoist. Re-

move the bolt that secures the trans-

mission filler tube to the cylinder

head.

3.
Remove the bolts that attach the

reinforcement plate at the rear of the

transmission oil pan and remove the

plate.

4.
Remove the three bolts that at-

tach the manual and downshift control

rod splash shield to the side rail and

remove the shield.
5.
Place a drain pan under the

transmission. Loosen all transmission

pan attaching bolts and allow the fluid

to drain. Remove the bolts from the

rear and both sides of the pan to

allow further drainage; then, finally

remove the pan. After all fluid has

been drained, install the pan using

four attaching bolts.

6. Remove the two bolts that attach

the cover to the lower end of the con-

verter housing.

7.
Remove the two front support

bracket bolts at the converter housing.

8. Remove the two drain plugs

from the converter and allow it to

drain.

9. Remove the four nuts that attach

the converter to the flywheel.

10.
Lift the fluid filler tube from

the transmission case.

11.
Remove the two idler arm

bracket bolts from the frame side rail

and allow the idler arm to hang free.

12.
Disconnect the starter cable

from the starter. Remove the starter

attaching bolts and remove the starter.

13.
Disconnect the oil cooler lines

from the transmission.

14.
Disconnect the vacuum hose

from the diaphragm.

15.
Loosen the parking brake ad-

justing nut at the equalizer and re-

move the retracting spring. Disconnect

the rear brake cables and remove the

equalizer from the bracket.

16.
Disconnect the speedometer

cable from the extension housing.

17.
Disconnect the drive shaft from

the transmission flange and position

the shaft out of the way.

18.
Disconnect the downshift rod

from the transmission downshift lever.

19.
Using tool T67P-7341-A, re-

move the manual selector rod from

the manual lever.

20.
Remove the lower bellcrank at-

taching bolts and remove the bell-

crank.

21.
Pry the upper bellcrank out of

the converter housing and allow it to

hang free.

22.
Remove the cooler lines from

the clip at the cylinder head.

23.
Remove the converter housing-

to-cylinder block lower attaching

bolts.

24.
Remove the two nuts that at-

tach the engine rear mounts to the

crossmember.

25.
Place a transmission jack under

the transmission and raise it just high

enough to remove the weight from the

crossmember.

26.
Remove the engine rear

support-to-extension housing attaching

bolts and remove the supports.
27.
Remove the crossmember-

to-frame attaching nuts and remove

the crossmember.

28.
Secure the transmission to the

jack with the safety chain. Lower the

transmission and remove the upper

converter housing-to-cylinder block at-

taching bolts.

29.
Move the transmission away

from the cylinder block.

30.
Carefully lower the transmis-

sion and remove it from under the ve-

hicle.

31.
Remove the converter and mount

the transmission in a holding fixture.

INSTALLATION-

LINCOLN CONTINENTAL

1.
Torque the two converter drain

plugs to specification.

2.
Install the converter on the sta-

tor support.

3.
Secure the transmission on a

transmission jack.

4.
Rotate the converter so that the

studs and drain plugs are in alignment

with those in the flywheel.

5.
Move the transmission toward the

cylinder block until they contact each

other. Install and torque the attaching

bolts to specification.

6. Secure the converter to the fly-

wheel with the four attaching nuts.

Torque the nuts to specification.

7.
Secure the converter access cover

to the converter housing with the at-

taching bolts.

8. Secure the two front support

brackets to the converter housing with

the attaching bolts.

9. Raise the transmission high en-

ough to position the crossmember. In-

stall the bolts, but do not tighten at

this time.

10.
Secure the engine rear support

to the extension housing and torque

the bolts to specification. At this time,

install and torque the crossmember-

to-frame attaching nuts to specifica-

tion.

11.
Lower the transmission and in-

stall the engine rear support-

to-crossmember attaching nuts and

plates.
Torque the •"its to specifica-

tion. Remove the transmission jack.

12.
Install the upper bellcrank in

the left side of the converter housing.

13.
Position the lower bellcrank to

the transmission and floor pan and se-

cure it with the two attaching bolts.

14.
Connect the downshift rod to

transmission downshift lever.

15.
Using tool T67P-7341-A, install

a new grommet in the manual lever.

Then, secure the manual selector rod

to the lever.procarmanuals.com

07-04-24

C-6 Automatic Transmission

07-04-24

CONVERTER PRESSURE RELIEF VALVE

THROTTLE PRESSURE

RELIEF BALL1/4 INCH

DIA. AND SPRING

CONVERTER

PRESSURE

RELIEF

SPRING

2-3 SHIFT

CHECK VALVE

D 1765-C

FIG. 39—Converter Pressure Relief Valve, Throttle Pressure Relief Valve,

and
2-3
Shift Check Valve Locations

FRONT PUMP

Tool
-
7775-AS

Tool -
T50T-
100-A

or 73-760

Tool
-T63L- 77837 -A

D 1636 -A

FIG. 40—Removing Front Pump

Seal

4.
Carefully position
the
separator

plate,
new
gasket
and the
lower valve

body
on the
upper valve body
and in-

stall
and
torque
the
attaching bolts
to

specification.

5.
Secure
the
screen
to the
lower

valve body with
the
attaching bolts

and torque them
to
specification.

6. Place
the
cutback control valve

(Fig.
38) in the
valve body.

7.
Place
the
coasting regulator

valve
in the
body.

8. Place
the
spring
D2
shift valve

and
the 1-2
shift valve
in the
body.

9. Place
the
throttle modulator

valve
and
spring
and the 2-3
shift

valve
in the
valve body.
D 1637-A

FIG. 41—Installing Front Pump

Seal

10.
Place
the
spring
and the 2-3

backout valve
in the
valve body.

11.
Place
the two
springs
and the

intermediate servo accumulator valve

in
the
valve body.

12.
Place
the
intermediate servo

modulator valve
and
spring
in the

body.

13.
Carefully place
the
valve retain-

ing plate
on the
body
and
secure
it

with
the
eight attaching screws. Tigh-

ten
the
screws
to
specification.

14.
Place
the
throttle booster valve

and spring
in the
valve body. Place

the manual
low 2-1
scheduling valve

and spring
in the
valve body
and in-
stall
the
retaining plate. Torque
the

attaching screws
to
specification.

15.
Place
the
main regulator,
two

springs, pressure booster valve
and the

sleeve
in the
valve body.

16.
Install
the
pressure booster

plate
and
torque
the two
attaching

screws
to
specification.

17.
Place
the
manual valve
in the

valve body
and
install
the
detent plug,

spring
and the
retaining
pin in the

body.

FRONT PUMP

The front seal
can be
replaced after

the pump
has
been installed
on the

transmission (Figs.
40 and 41).

Disassembly

1.
Remove
the two
seal-rings
and

the selective thrust washer (Fig.
42).

2.
Remove
the
large square-cut seal

from
the
O.D.
of the
pump housing.

3.
Remove
the 5
bolts that secure

the pump support
to the
pump hous-

ing. Lift
the
support from
the
housing.

4.
Remove
the
drive
and the
driven

gear from
the
housing.

Assembly

1.
Install
the
drive
and
driven gears

in
the
pump housing. Each gear
has

an identification mark
on one
face.

The identification mark
on
each gear

must
be
toward
the
front
of the
pump

housing.

2.
Position
the
pump support
in the

pump housing
and
install
and
torque

the five attaching bolts
to
specifica-

tion.

3.
Carefully install
two new
seal

rings
on the
pump support. Make sure

that
the
ends
of the
rings
are
engaged

to lock them
in
place. Install
a new

square-cut seal
on the O.D. of the

pump housing.

4.
Install
the
selective thrust wash-

er. Make sure that
the
correct thick-

ness selective washer
is
being used
to

obtain
the
specified
end
play.

5.
Place
the
pump
on
converter

making sure that
the
drive gear enga-

ges
the
converter
hub.
Rotate
the

pump
to
make sure that
the
gears
ro-

tate freely.

REVERSE-HIGH CLUTCH

Disassembly

1.
Separate
the
drive train
as
shown

in
Fig. 43.
Remove
the
pressure plate

retaining snap ring
as
shown
in Fig.

44.procarmanuals.com

07-04-29
C-6 Automatic Transmission

07-04-29

FORWARD CLUTCH

CYLINDER-7D424
OUTER SEAL

7A548
DISC SPRING FORWARD PRESSURE INTERNAL SPLINE REAR PRESSURE

7B070

PLATE-7B066

PLATE-7B164 PLATE-7B066

INNER SEAL

377130894
PISTON

7A262 STEEL

RING

7D256
SNAP

RING

377127-S

FIG. 52—Forward Clutch Disassembled

DISC

SPRING
EXTERNAL SPLINE

PLATE-7B442

7oo/-

7000-DD
SELECTIVE

SNAP RING

377126-S

D 1635-A

FIG. 53—Removing or Installing Disc Spring

distributor into place on the shaft. In-

stall the snap ring to secure it. Make

sure that the snap ring is seated in the

groove.

3.
Position the governor on the dis-

tributor (Fig. 62) and secure them

with the attaching screws.

ASSEMBLY OF TRANSMISSION

1.
Place the transmission case in a

holding fixture.

2.
Position the low-reverse clutch

piston so that check ball is in the 6 o'

clock position (toward bottom of case)
and tap the piston into place in the

case with a clean rubber hammer.

3.
Hold the one-way clutch inner

race in position and install and torque

the attaching bolts to specification.

4.
Install a low-reverse clutch re-

turn spring in each pocket in the

clutch piston. Press the springs firmly

into the piston to prevent them from

falling out.

5.
Position the spring retainer over

the springs and position the retainer

snap ring in place on the one-way

clutch inner race.
D1632-A

D1901-A

FIG. 54—Removing Forward

Clutch Piston

CHECK BETWEEN SNAP RING

AND PRESSURE PLATE

1902-A

FIG. 55—Checking Forward

Clutch Clearance

PICK

SCREWDRIVER

D 1633-A

FIG. 56—Removing Sun Gear

Snap Ringprocarmanuals.com