INFINITI QX30 2017 Owner's Manual

If you wish to confirm the restart:
5. Press <OK> to confirm.The [Tire Press. Monitor Restarted] message
appears in the vehicle information display.
After you have driven for a few minutes, the
system checks whether the current tire pres-
sures are within the specified range The new
tire pressures are then accepted as refer-
ence values and monitored
If you wish to cancel the restart:
6. Press the
button.
The tire pressure values stored at the last
restart will continue to be monitored
FCC Notice:
For USA:
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two
conditions: (1) This device may not cause harm-
ful interference, and (2) this device must accept
any interference received, including interfer-
ence that may cause undesired operation. NOTE
Changes or modifications not expressly ap-
proved by the party responsible for compliance
could void the user’s authority to operate the
equipment.
For Canada:
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) this
device may not cause interference, and (2) this
device must accept any interference, including
interference that may cause undesired opera-
tion of the device.
ON PAVEMENT AND OFF-ROAD
DRIVING PRECAUTIONS
Utility vehicles have a significantly higher roll-
over rate than other types of vehicles.
They have higher ground clearance than pas-
senger cars to make them capable of perform-
ing in a variety of on-pavement and off-road
applications. This gives them a higher center of
gravity than ordinary vehicles. An advantage of
higher ground clearance is a better view of the
road, allowing you to anticipate problems. How-
ever, they are not designed for cornering at the
same speeds as conventional 2-wheel drive
vehicles any more than low-slung sports cars
are designed to perform satisfactorily underoff-road conditions. If at all possible, avoid
sharp turns at high speeds. As with other
vehicles of this type, failure to operate this
vehicle correctly may result in loss of control or
vehicle rollover. In a rollover crash, an unbelted
person is significantly more likely to die than a
person wearing a seat belt.
For additional information, refer to
Driving
safety precautions later in this section.
AVOIDING COLLISION AND ROLLOVER
WARNING
Failure to operate this vehicle in a safe and
prudent manner may result in loss of control or
an accident.
Be alert and drive defensively at all times. Obey
all traffic regulations. Avoid excessive speed,
high speed cornering, or sudden steering ma-
neuvers, because these driving practices could
cause you to lose control of your vehicle.
As with any vehicle, loss of control could result
in a collision with other vehicles or objects or
cause the vehicle to roll over, particularly if the
loss of control causes the vehicle to slide side-
ways. Be attentive at all times, and avoid
driving when tired. Never drive when under the
5-10Starting and driving

influence of alcohol or drugs (including pre-
scription or over the- counter drugs which may
cause drowsiness). Always wear your seat belt
as outlined in the “Safety – Seats, seat belts
and supplemental restraint system” section of
this manual, and also instruct your passengers
to do so.
Seat belts help reduce the risk of injury in
collisions and rollovers.In a rollover crash, an
unbelted or improperly belted person is signifi-
cantly more likely to be injured or killed than a
person properly wearing a seat belt.
OFF-ROAD RECOVERY
While driving, the right side or left side wheels
may unintentionally leave the road surface. If
this occurs, maintain control of the vehicle by
following the procedure below. Please note that
this procedure is only a general guide. The
vehicle must be driven as appropriate based on
the conditions of the vehicle, road and traffic.
1. Remain calm and do not overreact.
2. Do not apply the brakes.
3. Maintain a firm grip on the steering wheel with both hands and try to hold a straight
course.
4. When appropriate, slowly release the accel- erator pedal to gradually slow the vehicle. 5. If there is nothing in the way, steer the
vehicle to follow the road while vehicle
speed is reduced. Do not attempt to drive
the vehicle back onto the road surface until
vehicle speed is reduced.
6. When it is safe to do so, gradually turn the steering wheel until both tires return to the
road surface. When all tires are on the road
surface, steer the vehicle to stay in the
appropriate driving lane.
If you decide that it is not safe to return the
vehicle to the road surface based on vehicle,
road or traffic conditions, gradually slow the
vehicle to a stop in a safe place off the road.RAPID AIR PRESSURE LOSS
Rapid air pressure loss or a “blow-out” can
occur if the tire is punctured or is damaged due
to hitting a curb or pothole. Rapid air pressure
loss can also be caused by driving on under-
inflated tires.
Rapid air pressure loss can affect the handling
and stability of the vehicle, especially at high-
way speeds.
Help prevent rapid air pressure loss by main-
taining the correct air pressure and visually
inspect the tires for wear and damage. For
additional information, refer to “Wheels and
tires” in the “Maintenance and do-it-yourself” section of this manual. If a tire rapidly loses air
pressure or “blows-out” while driving, maintain
control of the vehicle by following the proce-
dure below. Please note that this procedure is
only a general guide. The vehicle must be driven
as appropriate based on the conditions of the
vehicle, road and traffic.
WARNING
The following actions can increase the chance
of losing control of the vehicle if there is a
sudden loss of tire air pressure. Losing control
of the vehicle may cause a collision and result
in personal injury.
•The vehicle generally moves or pulls in the
direction of the flat tire.
•Do not rapidly apply the brakes.
•Do not rapidly release the accelerator pedal.
•Do not rapidly turn the steering wheel.
1. Remain calm and do not overreact.
2. Maintain a firm grip on the steering wheel with both hands and try to hold a straight
course.
3. When appropriate, slowly release the accel- erator pedal to gradually slow the vehicle.
Starting and driving5-11

4. Gradually steer the vehicle to a safe locationoff the road and away from traffic if possible.
5. Lightly apply the brake pedal to gradually stop the vehicle.
6. Turn on the hazard warning flashers and contact a roadside emergency service to
change the tire. For additional information,
refer to Flat tire in the6. In case of
emergency section.
DRINKING ALCOHOL/DRUGS AND
DRIVING
WARNING
Never drive under the influence of alcohol or
drugs. Alcohol in the bloodstream reduces co-
ordination, delays reaction time and impairs
judgement. Driving after drinking alcohol in-
creases the likelihood of being involved in an
accident injuring yourself and others. Addi-
tionally, if you are injured in an accident, alco-
hol can increase the severity of the injury.
INFINITI is committed to safe driving. However,
you must choose not to drive under the influ-
ence of alcohol. Every year thousands of people
are injured or killed in alcohol-related acci-
dents. Although the local laws vary on what is
considered to be legally intoxicated, the fact is that alcohol affects all people differently and
most people underestimate the effects of alco-
hol.
Remember, drinking and driving don’t mix! And
that is true for drugs, too (over-the-counter,
prescription, and illegal drugs). Don’t drive if
your ability to operate your vehicle is impaired
by alcohol, drugs, or some other physical con-
dition.
DRIVING SAFETY PRECAUTIONS
Your INFINITI is designed for both normal and
off-road use. However, avoid driving in deep
water or mud as your INFINITI is mainly de-
signed for leisure use, unlike a conventional
off-road vehicle.
Remember that 2–wheel drive vehicles are less
capable than all-wheel drive (AWD) models for
rough road driving and extrication when stuck
in deep snow or mud, or the like.
Please observe the following precautions:
WARNING
•Spinning the front wheels on slippery sur-
faces may cause the AWD warning message
to display and the AWD system to automati-
cally switch from the AWD to 2WD mode.
This could reduce the traction. Be especially
careful when towing a trailer. (AWD models)
•Drive carefully when off the road and avoid
dangerous areas. Every person who drives
or rides in this vehicle should be seated
with their seat belt fastened. This will keep
you and your passengers in position when
driving over rough terrain.
•Do not drive across steep slopes. Instead
drive either straight up or straight down the
slopes. Off-road vehicles can tip over side-
ways much more easily than they can for-
ward or backward.
•Many hills are too steep for any vehicle. If
you drive up them, you may stall. If you drive
down them, you may not be able to control
your speed. If you drive across them, you
may roll over.
•Do not shift gears while driving on downhill
grades as this could cause loss of control of
the vehicle.
•Stay alert when driving to the top of a hill. At
the top there could be a drop-off or other
hazard that could cause an accident.
•If your engine stalls or you cannot make it to
the top of a steep hill, never attempt to turn
around. Your vehicle could tip or roll over.
5-12Starting and driving

Always back straight down in R (Reverse)
gear and apply brakes to control your
speed.
•Heavy braking going down a hill could cause
your brakes to overheat and fade, resulting
in loss of control and an accident. Apply
brakes lightly and use a low gear to control
your speed.
•Unsecured cargo can be thrown around
when driving over rough terrain. Properly
secure all cargo so it will not be thrown
forward and cause injury to you or your pas-
sengers.
•Secure heavy loads in the cargo area as far
forward and as low as possible. Do not
equip the vehicle with tires larger than
specified in this manual. This could cause
your vehicle to roll over.
•Do not grip the inside or spokes of the steer-
ing wheel when driving off-road. The steer-
ing wheel could move suddenly and injure
your hands. Instead drive with your fingers
and thumbs on the outside of the rim.
•Before operating the vehicle, ensure that
the driver and all passengers have their seat
belts fastened.
•Always drive with the floor mats in place as
the floor may become hot.
•Lower your speed when encountering
strong crosswinds. With a higher center of
gravity, your INFINITI is more affected by
strong side winds. Slower speeds ensure
better vehicle control.
•Do not drive beyond the performance capa-
bility of the tires, even with AWD engaged.
•For AWD equipped vehicles, do not attempt
to raise two wheels off the ground and shift
the transmission to any drive or reverse po-
sition with the engine running. Doing so
may result in drivetrain damage or unex-
pected vehicle movement which could re-
sult in serious vehicle damage or personal
injury.
•Do not attempt to test an AWD equipped
vehicle on a 2-wheel dynamometer (such as
the dynamometers used by some states for
emissions testing), or similar equipment
even if the other two wheels are raised off
the ground. Make sure you inform test facil-
ity personnel that your vehicle is equipped
with AWD before it is placed on a dynamom-
eter. Using the wrong test equipment may
result in drivetrain damage or unexpectedvehicle movement which could result in se-
rious vehicle damage or personal injury.
•When a wheel is off the ground due to an
unlevel surface, do not spin the wheel ex-
cessively.
•Accelerating quickly, sharp steering ma-
neuvers or sudden braking may cause loss
of control.
•If at all possible, avoid sharp turning ma-
neuvers, particularly at high speeds. Your
INFINITI vehicle has a higher center of grav-
ity than a passenger car. The vehicle is not
designed for cornering at the same speeds
as passenger cars. Failure to operate this
vehicle correctly could result in loss of con-
trol and/or a rollover accident.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted, or
radial), and tread pattern on all four wheels.
Install tire chains on the front wheels when
driving on slippery roads and drive care-
fully.
•Be sure to check the brakes immediately
after driving in mud or water.
Starting and driving5-13

•Avoid parking your vehicle on steep hills. If
you get out of the vehicle and it rolls for-
ward, backward or sideways, you could be
injured.
•Whenever you drive off-road through sand,
mud or water as deep as the wheel hub,
more frequent maintenance may be re-
quired. For additional information, refer to
Maintenance schedulesin the
9. Maintenance and Schedules section.
ALL-WHEEL DRIVE (AWD) DRIVING
SAFETY PRECAUTIONS (IF SO
EQUIPPED)
WARNING
•Replacing tires with those not originally
specified by INFINITI could affect the proper
operation of the TPMS.
•Always use tires of the same type, size,
brand, construction (bias, bias-belted or ra-
dial), and tread pattern on all four wheels.
Install tire chains on the front wheels when
driving on slippery roads and drive care-
fully.
•This vehicle is not designed for offroad
(rough road) use. Do not drive on sandy or
muddy roads that tires may get stuck in.
•For AWD equipped vehicles, do not attempt
to raise two wheels off the ground and shift
the transmission to any D (Drive) or R (Re-
verse) position with the engine running. Do-
ing so may result in drivetrain damage or
unexpected vehicle movement which could
result in serious vehicle damage or personal
injury
•Do not attempt to test an AWD equipped
vehicle on a 2-wheel dynamometer, (such
as the dynamometers used by some states
for emissions testing), or similar equipment
even if the other two wheels are raised off
the ground. Make sure you inform test facil-
ity personnel that your vehicle is equipped
with AWD before it is placed on a dynamom-
eter. Using the wrong test equipment may
result in drivetrain damage or unexpected
vehicle movement which could result in se-
rious vehicle damage or personal injury.
•When a wheel is off the ground due to an
unlevel surface, do not spin the wheel
excessively. The INFINITI Vehicle Immobilizer System will not
allow the engine to start without the use of the
registered key.
If the engine fails to start using the registered
key, it may be due to interference caused by
another registered key, an automated toll road
device or automated payment device on the key
ring. Restart the engine using the following
procedures:
1. Leave the ignition switch in the ON position
for approximately 5 seconds.
2. Turn the ignition switch to the OFF or LOCK position and wait approximately 5 seconds.
3. Repeat Step 1 and 2 again.
4. Restart the engine while holding the device (which may have caused the interference)
separate from the registered key.
If the no start condition re-occurs, INFINITI
recommends placing the registered key on a
separate key ring to avoid interference from
other devices.
INFINITI VEHICLE IMMOBILIZER SYSTEM
5-14Starting and driving

0OFF position
1ACC position
2ON position
3START position
WARNING
Never remove the key or turn the ignition
switch to the OFF position while driving. The
steering wheel will lock and could cause the
driver to lose control of the vehicle. This could
result in serious vehicle damage or personal
injury.
CAUTION
Use electrical accessories with the engine run-
ning to avoid discharging the vehicle battery.
If you must use accessories while the engine is
not running, do not use them for extended pe-
riods of time and do not use multiple electrical
accessories at the same time.
The switch includes an anti-theft steering lock
device.
STEERING LOCK
To lock the steering wheel
1. Turn the key to the OFF position.
2. Remove the key from the ignition switch.
3. Turn the steering wheel 1/6 of a turn clock- wise from the straight up position.
To unlock the steering wheel
1. Insert the key into the ignition switch.
2. Gently turn the key while rotating the steer- ing wheel slightly right and left.
KEY POSITIONS
OFF (Normal parking position)
0
The ignition key can only be removed when in
this position.
The steering lock can only be locked in this
position.
ACC (Accessories)/1
The engine is turned off without locking the
steering wheel. This position activates electrical
accessories, such as the radio, when the engine
is not running.
ON (Normal operating position)2
This position turns on the ignition system and
electrical accessories.
START3
The engine starter activates and the engine will
start. As soon as the engine has started, release
the key immediately. It will return to the ON
position.
NPA1483
IGNITION SWITCH
Starting and driving5-15

NOTE
For vehicles fitted with Idle Stop/Start System:
When the engine is automatically stopped by
the Idle Stop/Start System the ignition switch
can still be operated as usual.
At the end of a journey turn the ignition OFF to
avoid a discharged battery. The Idle Stop/Start
System does not automatically turn ignition off.•Make sure the area around the vehicle is
clear.
•Check fluid levels such as engine oil, cool-
ant, brake fluid, and windshield-washer fluid
as frequently as possible, or at least when-
ever you refuel.
•Check that all windows and lights are clean.
•Visually inspect tires for their appearance
and condition. Measure and check the tire
pressure for proper inflation.
•Check that all doors are closed.
•Position seat and adjust head restraints/
headrests.
•Adjust the inside and outside rear view mir-
rors.
•Fasten your seat belt and ask all passengers
to do likewise.
•Check the operation of the warning lights
when the ignition switch is pushed to the ON
position.
STARTING PROCEDURE WITH THE KEY
0OFF position
1ACC position
2ON position
3START position
1. Apply the parking brake.
2. Shift the transmission to position P (Park) by pressing the <P> button.
The transmission position indicator in the
vehicle information display shows <P>
When the transmission is in position N (Neu-
tral), you can also start the engine with the
brake pedal depressed.
The starter is designed not to operate if the shift
lever is in any of the driving positions.
NPA1483
BEFORE STARTING ENGINE STARTING ENGINE
5-16Starting and driving

3. Turn the key to the START position3in the
ignition lock and release it as soon as the
engine is running.
If the engine is very hard to start because it is
flooded, depress the accelerator pedal all the
way to the floor and hold it. Turn the ignition
switch to the START position to start cranking
the engine. After 5 or 6 seconds, stop cranking
by turning the ignition switch to OFF. After
cranking the engine, release the accelerator
pedal. Crank the engine with your foot off the
accelerator pedal by depressing the brake
pedal and turning the ignition switch to start
the engine. If the engine starts, but fails to run,
repeat the above procedure.CAUTION
Do not operate the starter for more than 15
seconds at a time. If the engine does not start,
turn the ignition key to the OFF position and
wait 10 seconds before cranking again, other-
wise the starter could be damaged.
4. Warm-up
Allow the engine to idle for at least 30
seconds after starting. Do not race the en-
gine while warming it up. Drive at moderate
speed for a short distance first, especially in
cold weather. In cold weather, keep the
engine running for a minimum of2-3
minutes before shutting it off. Starting and
stopping the engine over a short period of
time may make the vehicle more difficult to
start.
5. To stop the engine, Shift the transmission to position P (Park) by pressing the <P> button.
and turn the ignition switch to the OFF
position. NOTE
Care should be taken to avoid situations that can
lead to potential battery discharge and potential
no-start conditions such as:
•Installation or extended use of electronic
accessories that consume battery power
when the engine is not running (Phone char-
gers, GPS, DVD players, etc.)
•Vehicle is not driven regularly and/or only
driven short distances. In these cases, the
battery may need to be charged to maintain
battery health.
Starting and driving5-17

DRIVING WITH AUTOMATIC
TRANSMISSION
Driving precautions
•Do not depress the accelerator pedal while
shifting from P (Park) or N (Neutral) to R (Re-
verse), D (Drive), or M (Manual shift mode).
Always depress the brake pedal until shifting
is completed. Failure to do so could cause you
to lose control and have an accident.
•Cold engine idle speed is high, so use caution
when shifting into a forward or reverse gear
before the engine has warmed up.
•Never shift to either the P (Park) or R (Reverse)
position while the vehicle is moving forward
and P (Park) or D (Drive) position while the
vehicle is reversing. This could cause an acci-
dent or damage the transmission.
•Except in an emergency, do not shift to the N
(Neutral) position while driving. Coasting
with the transmission in the N (Neutral) posi-
tion may cause serious damage to the trans-
mission.
WARNING
•Do not downshift abruptly on slippery
roads. this may cause a loss of control.
CAUTION
•To avoid possible damage to your vehicle;
when stopping the vehicle on an uphill
grade, do not hold the vehicle by depress-
ing the accelerator pedal. The foot brake
should be used for this purpose.
•Except in an emergency, do not shift to the N
(Neutral) position while driving. Coasting
with the transmission in the N (Neutral) po-
sition may cause serious damage to the
transmission.
Starting the vehicle
1. After starting the engine, fully depress thebrake pedal before shifting the shift lever to
R (Reverse), D (Drive) or Manual shift mode.
2. Keep the brake pedal depressed and push the shift lever to shift into a driving gear.
3. Release the parking brake and brake, then gradually put the vehicle in motion by press-
ing the accelerator pedal.
The automatic transmission is designed so that
the brake pedal MUSTbe depressed before
shifting from P (Park) to any drive position while
the ignition switch is ON.
Shifting
P Park position with parking lock
R Reverse
N Neutral
D Drive
NSD585
DRIVING THE VEHICLE
5-18Starting and driving

Transmission position display:
NOTE
If the transmission position display in the ve-
hicle information display is not working, you
should pull away carefully to check whether the
desired transmission position IS engaged. Ide-
ally, you should select transmission position D
and automatic drive program E or S.
The shift lever indicator
1located in the lower
part of the vehicle information display shows
the current position of the transmission.
It shows the P,R,N,D modes when the transmis-
sion is in auto mode or the shift position when
the transmission is in manual mode.
WARNING
Apply the parking brake if the shift lever is in
any position while the engine is not running.
Failure to do so could cause the vehicle to move
unexpectedly or roll away and result in serious
personal injury or property damage.
CAUTION
Use the P (Park) or R (Reverse) position only
when the vehicle is completely stopped. P (Park)
:
CAUTION
To prevent transmission damage, use the P
(Park) position only when the vehicle is com-
pletely stopped.
Use this position when the vehicle is parked or
when starting the engine. Always make sure
that the vehicle is completely stopped before
pressing button
1to engage the P (Park)
position. For maximum safety, the brake pedal
must be depressed before engaging the P (Park)
position. Use this position together with the
parking brake. When parking on a hill, first
depress the brake pedal, apply the parking
brake and then engage the P (Park) position.
The parking lock should not be used as a brake
when parking. In order to secure the vehicle,
NSD649NSD586
Starting and driving5-19