ISUZU AXIOM 2002 Service Repair Manual

8F±25 BODY STRUCTURE
A10R200007

8F±26BODY STRUCTURE
Rear Section
A10R200018

8F±27 BODY STRUCTURE
A10R200009

8F±28BODY STRUCTURE
Side Body Section (Front side)
A10R200019

8F±29 BODY STRUCTURE
A10R200011

8F±30BODY STRUCTURE
Side Body Section (Rear side)
A10R200020

8F±31 BODY STRUCTURE
A10R200013

8F±32BODY STRUCTURE
General Description (Body)
This publication contains essential removal, installation,
adjustment and maintenance procedures.
Instrument Panel Assembly
Parts Location
740R200024
Legend
(1) Cross Beam
(2) Vent Duct Assembly
(3) Instrument Panel Stay
(4) Passenger Air Bag
(5) Passenger Air Bag Cover
(6) Dash Side Trim Panel (RH)
(7) Instrument Upper Reinforcement
(8) Glove Box Side Reinforcement
(9) Passenger Lower Bracket
(10) Glove Box
(11) Display Unit
(12) Audio Kit(13) Front Console Assembly
(14) Knee Pad
(15) Center Cluster Assembly
(16) Cluster Upper Cover
(17) Instrument Panel Driver Lower Cover
Assembly
(18) Driver Knee Bolster Assembly
(19) Dash Side Trim Panel (LH)
(20) Meter Cluster Assembly
(21) Instrument Panel Center Reinforcement
(22) Meter Assembly
(23) Instrument Panel Assembly
(24) Instrument Harness Assembly

8F±33 BODY STRUCTURE
Removal
CAUTION: F o r p recautions on installation or
removal of SRS ± air bag system, refer to
Supplemental Restraint System (SRS) ± AIR BAG in
Restraint section.
1. Disconnect the battery ground cable.
2. Pry the knee pads (4).
3. Remove the cluster upper cover (1) and connectors.
4. Remove the center cluster assembly (2).

Remove six screws and pull out the cluster at the six
clip positions.

Disconnect the cigarette lighter (6), ash tray (5)
illumination and hazard switch (3) connectors.
740R200008
5. Remove the display unit.

Remove the four fixing screws and connectors.
6. Remove the audio kit.

Remove the four fixing screws and connectors.
7. Remove the front and rear consoles.

Refer to
Consoles in Exterior/Interior Trim section.
8. Remove the dash side trim panels.

Remove the sill plates, then remove the trim panels.
9. Remove the glove box.

Remove the two fixing screws.
470RW002
10. Remove the instrument panel driver lower cover
assembly.

Remove the engine hood opener two fixing screws
and another one fixing screw.
After four clips are pried, disconnect switch
connector and duct.
610R200007
11. Remove the meter cluster assembly.

Remove the six fixing screws and switch
connectors.
12. Remove the meter assembly.

Remove the four fixing screws and disconnect the
connectors.
13. Remove the driver knee bolster assembly.

Remove the six fixing bolts and screw.
14. Remove the instrument panel assembly.
CAUTION: F o r p recautions on installation or
removal of SRS ± air bag system, refer to
Supplemental Restraint System (SRS) ± AIR BAG in
Restraint section.

8F±34BODY STRUCTURE

Disconnect the instrument harness connectors (six
connectors on the driver's side, three connectors
on the passenger side and two connectors on the
center side).

Disconnect radio antenna cable plug and the
ground cable fixing bolts from dash side panel.

Remove the two fixing bolts of passenger air bag
assembly and disconnect the connector.

Remove the two fixing screws from fuse box.

After pry the three hole cover from the surface of
instrument panel, remove the three nuts.

Remove the six bolts and one screw.
740R200022
15. Remove the passenger air bag (1).

Remove the four fixing nuts.
CAUTION: F o r p recautions on installation or
removal of SRS ± air bag system, refer to
Supplemental Restraint System in Restraint section.
827RY00004
16. Remove the vent duct assembly.

Remove the five fixing screws.17. Remove the passenger lower bracket.

Remove the three screws.
18. Remove the glove box side reinforcement.
19. Remove the instrument upper reinforcement.

Remove the nine screws.
20. Remove the instrument panel center reinforcement.

Remove the six screws.
21. Remove the instrument panel harness assembly (1).

Remove the clips.
740R200023
22. Remove the instrument panel stays.

Remove the two fixing nuts and two fixing bolts for
each bracket.
23. Remove the cross beam.

Remove the five fixing nuts, two fixing bolts (upper)
and six fixing bolts (lower).
840RW005
Installation
To install, follow the removal steps in the reverse order.