ISUZU KB P190 2007 Workshop Repair Manual

ELECTRICAL-BODY AND CHASSIS 8A-183

CIRCUIT DIAGRAM C24SE (RHD) WITH REAR FOG LIGHT


RTW 780XF012401

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-184 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM HFV6


RTW 78AXF015101


BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-185

CIRCUIT DIAGRAM 4JJ1-TC/4JK1-TC (RHD) SOUTH AFRICA, 4JA1T (L)

RTW 78AXF020101

BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007

8A-186 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM 4JJ1-TC/4JK1-TC (LHD) G.EXP


RTW 78AXF022901


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-187

RTW 780SH000601
FOG LIGHT (A type)
Removal
1. Disconnect the fog light connector 1 .
2. Remove two attaching nuts
2.
3. Pull the fog light assembly toward the vehicle front to remove it from the holding bracket
3 .
4. Remove the bulb with socket. • Turn the socket
4 counterclockwise to remove it.
5. Remove the bulb. • Release the lock spring.
• Pull out the bulb.


FOG LIGHT (B type)
Removal
1. Remove the radiator grille.
2. Remove the front bumper
3. Disconnect the fog light connector.
4. Remove the fog light.


5. Remove the bulb from the socket.
• Remove the cover by turning it counterclockwise out
side the lock spring.
• Remove the bulb.



Hold the bulb by the flange when replacing it.
Do not touch the bulb with your hands.

Installation
To install the fog light, follow the removal procedure in reverse
order.
Pay close attention to the important points mentioned in the
following paragraphs.





Bulb
Be absolutely sure that the fog light bulb is correctly installed.
This will prevent a poor contact and open circuit.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-188 ELECTRICAL-BODY AND CHASSIS

RTW 780SH000801
FOG LIGHT ADJUSTMENT (A type)
Vertical Adjustment
Turn the adjusting screw with a screwdriver to adjust the aim of
the fog light vertically.

FOG LIGHT ADJUSTMENT (B type)
Vertical Adjustment
Turn the adjusting screw with a screwdriver to adjust the aim of
the fog light vertically.


RTW 78ASH000401
FRONT FOG & REAR FOG SWITCH



RTW 48ASH000401
Inspection
Check to see if there is any continuity between the terminals of
the front fog light switch.
Replace the switch when the result of inspection is found
abnormal.

Removal
Preparation:
Disconnect the battery ground cable.
1. Ventilation grille
2. Harness connector
3. Front fog light & Rear fog light switch To remove the switch, push the lock from the back side of
the cluster assembly.
4. Remove the bulb.


BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-189

RTW 78ASH000501
Installation
To install, follow the removal steps in the reverse noting the
following point.
1. Push in the switch with your fingers until it locks securely.



BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-190 ELECTRICAL-BODY AND CHASSIS
REAR FOG LIGHT
PARTS LOCATION (RHD)







RTW 78AXF037101 & RTW 78AXF043301

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

ELECTRICAL-BODY AND CHASSIS 8A-191

PARTS LOCATION (LHD)





RTW 78AXF037201 & RTW 78AXF043401

BACK TO CHAPTER INDEX TO MODEL INDEXISUZU KB P190 2007

8A-192 ELECTRICAL-BODY AND CHASSIS

CIRCUIT DIAGRAM 4JJ1-TC/4JK1-TC (LHD) G.EXP


RTW 78AXF023101


BACK TO CHAPTER INDEX
TO MODEL INDEXISUZU KB P190 2007