electrical JAGUAR X308 1998 2.G Workshop Manual

                    Knock Sensor  (KS)  RH  (18.30.93)  
                    
Variable Camshaft  Timing  (VCT)  Oil  Co ntrol
 
Solenoid  (18.30.90)  
 
        
307:  Automatic  Transmission/Transaxle  
 
             307‐01A : Automatic  Transmission/Transaxle  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA V8  ‐ AJ27  
                 Specification  
                 Description  and  Operation  
                     Transmission  Description 
                 Diagnosis  and  Testing  
                     Diagnostic Strategy  
                 General Procedures  
                     Transmission  Fluid Drain  and  Refill  (44.24.02)  
                 In‐Ve
hicle  Repair  
                     Electronic Pressure  Control (EPC)  Solenoid  (44.15.51)  
                     Extension Housing  Seal  (44.20.18)  
                     Extension Housing  O ‐Ring  Seal  (44.20.19)  
                     Main Control  Valve Body  (44.40.01)  
                     Output Shaft  Speed  (OSS)  Sensor  (44.15.41)  
                     Shift Solenoids  (SS)  (44.15.50)  
                     Transmission  Control Module  (TCM)  (44.15.32)  
                     Transmission  Fluid Filter  (44.24.07)  
                     Transmission  Fl
uid  Pan  (44.24.04)  
                     Transmission  Fluid Pan  Gasket  (44.24.05)  
                     Transmission  Internal Wiring  Harness  (44.15.35)  
                     Transmission  Internal Wiring  Harness  Electrical  Connector  O‐Ring  Seals  
            (44.24.20) 
                     Transmission  Range (TR)  Sensor  
                     Transmission  Support Insulator  (12.45.04)  
                     Turbine Shaft  Speed  (TSS)  Sensor  (44.15.40)  
                 Removal 
                     Transmission  (44.20.01) 
                 Disassembly  and  Assembly  of Subassemblies  
                     Input Sh
aft  Seal  (44.32.07)  
                     Torque Converter  (44.17.07)  
                 Installation  
                     Transmission  (44.20.01) 
Mass
 
Airflow
 
Sen s
or
 
Knock
 Sensor
 (KS)
 LH
 (18.30.92)
 

 
            307‐01B : A u
tomatic
 Transmission/Transaxle  ‐ 4.0L  SC  V8 ‐ AJ26  
                 Specification  
                 Description  and  Operation  
                     Transmission  Description 
                 Diagnosis  and  Testing  
                     Diagnostic Strategy  
                 General Procedures  
                     Transmission  Fluid Drain  and  Refill  (44.24.02)  
                 In‐Vehicle  Repair  
                     Extension Housing  Seal  (44.20.18)  
                     Main Control  Valve Body  (44.40.01)  
                     Transmission  Fluid Filter  (44.24.07)  
                     Transmission  Fl
uid  Pan  Gasket  (44.24.05)  
                     Transmission  Internal Wiring  Harness  Electrical  Connector  O‐Ring  Seals  
            (44.24.20) 
                     Transmission  Support Insulator  (12.45.04)  
                 Removal 
                     Transmission  (44.20.01) 
                 Disassembly  and  Assembly  of Subassemblies  
                     Input Shaft  Seal  (44.32.07)  
                     Torque Converter  (44.17.07)  
                 Installation  
                     Transmission  (44.20.01) 
 
             307‐02A : Transmission/Transaxle  Cooling  ‐ 3.2L  NA  V8  ‐ AJ26/4.0L  NA  V8  ‐ AJ
27  
                 Description  and  Operation  
                     Transmission  Cooling 
 
             307‐02B : Transmission/Transaxle  Cooling  ‐ 4.0L  SC  V8 ‐ AJ26  
                 Description  and  Operation  
                     Transmission  Cooling 
 
             307‐05A : Automatic  Transmission/Transaxle  External  Controls  ‐ 3.2L  NA  V8  –  
            AJ26/4.0L NA  V8  ‐ AJ27  
                 Description  and  Operation  
                     External Controls  

            310‐01:  Fu el Tank  and  Lines  
                 Removal and  Installation  
                     Fuel Level  Sensor  (88.25.32)  
                     Fuel Pump  (19.45.08)  
                     Fuel Tank  (19.55.01)  
 
             310‐02
:
 Acceleration  Control  
                 General Procedures  
                     Accelerator  Cable  Adjustment  (12.20.05)  
                 Removal and  Installation  
                     Accelerator  Cable  (19.20.06)  
 
             310‐03:  Speed  Control  
                 Diagnosis  and  Testing  
                     Speed Con
trol 
 
    4:  Electrical  
 
        412:  Climate  Control  System  
 
             412‐00:  Climate  Control  System  ‐ General  Information 
                 Specification  
                 Description  and  Operation  
                     Climate Control System  
                 Diagnosis  and  Testing  
                     Climate Control System  
                 General Procedures  
                     Air Conditioning  (A/C)  System  Check ‐  Retail Procedure  
                     Air Conditioning  (A/C)  System  Recovery,  Evacuation  and  Charging  (82.30.30)  
                     Contaminated  Refrigerant  Ha
ndling  
                     Manifold Gauge  Set Connection  
                     Refrigerant  Adding (82.30.02)  
                     Refrigerant  Oil Adding  
                     Refrigerant  System Tests  
 
             412‐01:  Air  Distribution  and  Filtering  
                 Description  and  Operation  

                    Side Turn  Signal  Lamp  (86.41.41)  
                     Side Turn  Signal  Lamp  Bulb  (86. 41.42)  
 
             417‐02
:
 Interior  Lighting  
                 Specification  
                 Description  and  Operation  
                     Interior Lighting  
                 Diagnosis  and  Testing  
                     Interior Lighting  
                 Removal and  Installation  
                     Door Courtesy  Lamp (86.40.38)  
                     Door Courtesy  Lamp Bulb  (86.40.47)  
                     Door Courtesy  Lamp Lens  (86.40.35)  
                     Glove Co
mpartment  Lamp  (86.45.08)  
                     Luggage Compartment  Lamp (86.45.16)  
                     Vanity Mirror  Lamp  (76.10.50)  
 
             417‐04:  Daytime  Running  Lamps  (DRL) 
                 Description  and  Operation  
                     Daytime Running Lamps  (DRL) 
                 Diagnosis  and  Testing  
                     Daytime Running Lamps  (DRL) 
 
        418:  Electrical  Distribution  
 
             418‐00:  Module  Communications  Network  
                 Description  and  Operation  
                     Communications  Ne
twork 
                                                      Removal
 and  Installation  
                     Battery
 Junction  Box  (BJB)  (86.70.69)  
                     Central
 Junction  Box (CJB)  (86.70.72)  
                     Front
 Auxiliary  Junction  Box  (86.70.73)  
                     Rear
 Auxiliary  Junction  Box  (86.70.74)  
 
  
418 ‐02:  Wiring  Harnesses  
Description  and  Operati
on
 
Wiring  Harness  
General  Procedures  
Wiring  Harness  Repair 

General Infor
mation - Gene
ral Service Information
Description an
d Operation
Safety Notice


Appropri
ate service me
thods and proper repair procedures are essential for the safe, reliable operation of all motor vehicles,
as well as the safety of the person do ing the work. This manual provides genera l directions for accomplishing service and
repair work with tested, effect ive, techniques. Following them will help assure reliability.
There are numerous variations in procedures, techniques, tools, and parts for servicing vehicles, as well as in the skill of the
person doing the work. This manual cannot possibly anticipate all such variations and provide advice or cautions as to each.
Accordingly, anyone who depart s from the instructions provided in the manua l must first establish that neither personal
safety nor vehicle integrity is compromised from choices of methods, tools or parts.
Notes, Ca
utions and Warnings
Throughout
this manual, important inform
ation is highlighted by the use of notes, cautions and warnings. NOTES give
additional information on a topic or proc edure, CAUTIONS are given to prevent da mage to the vehicle, and WARNINGS are
given to prevent personal injury.

Worksh
op Manual Organization
This
manual incorporates descript
ive, diagnostic, and repair information to help trained Jaguar technicians complete service
and rectification procedures. The informat ion can be accessed by choosing the appropriate five digit section number. For
example, Section 412-03 covers air conditioning , which is part of the Climate Control System.
The manual is organized into groups covering generic aspects of the vehicle systems; the first digit of the section
number represents a group se lected from the following:
1. General Information.
2. Chassis.
3. Powertrain.
4. Electrical.
5. Body and Paint.
Each of the groups comprises sections re lating to specific areas of the vehicle.
The second and third digits of the section number indicate the vehicle system.
The last two digits of the se ction number define the system covered, more specifically.
Each section comprises one or more of the following sub-sections:
Specification

Before inspecting a component for wear or per
forming a dimensional check,
ensure that it is absolutely clean; a slight smear
of grease can conceal an incipient failure. When a component is to be checked dimensionally against figures quoted for it,
use the correct equipment (surface plates, micrometers, dial gauges etc.) in serviceable condition. The use of makeshift
equipment can be dangerous. Reject a component if its dimensio ns are outside the limits quoted, or if damage is apparent.
A part may be refitted if its critical di mension is exactly to the limit size and it is otherwise satisfactory. Use Plastigauge 12
Type PG-1 for checking bearing surface clearance, e.g. big end bearing shell to crank jour nal. Instructions for the use of
Plastigauge and a scale giving bearing clearances in steps of 0.0025 mm (0.0001 in) are supplied with the package.
Safety
Precautions
• WAR
NINGS:
WORKING ON THE FUEL SYSTEM RESULTS IN FUEL AND FUEL VAPOUR BEING PRESENT IN THE ATMOSPHERE. FUEL
VAPOUR IS EXTREMELY FLAMMABLE, HENCE GREAT CARE MUST BE TAKEN WHILST WORKING ON THE FUEL SYSTEM.
ADHERE STRICTLY TO THE FOLLOWING PRECAUTIONS:
DO
NOT SMOKE IN THE WORK AREA.
DISP

LAY 'NO SMOKING' SIGNS AROUND THE AREA.
DISCONNECT TH

E BATTERY BEFORE WORKING ON THE FUEL SYSTEM.
DO NOT CONNEC

T/DISCONNECT ELECTRICAL CIRCUITS
, USE ELECTRICAL EQUIPMENT OR OTHER TOOLS OR
ENGAGE IN WORKING PRACTICES WHICH IN ANY WAY MAY RESULT IN THE PRODUCTION OF SPARKS.
ENS
URE THAT A CO2 FIRE EXTINGUISHER IS CLOSE AT HAND.
ENS

URE THAT DRY SAND IS AVAILABLE TO SOAK UP ANY FUEL SPILLAGE.
EMP

TY FUEL USING SUITABLE FIRE PROOF EQUIPMENT IN
TO AN AUTHORIZED EXPLOSION PROOF CONTAINER.
DO NOT EMP
TY FUEL WHILE WORKING IN A WORKSHOP OR A PIT.
ENS

URE THAT WORKING AREA IS WELL VENTILATED.
ENS

URE THAT ANY WORK ON THE FUEL SYSTEM IS ON
LY CARRIED OUT BY EXPERIENCED AND WELL QUALIFIED
MAINTENANCE PERSONNEL.
ENS
URE THAT FUME EXTRACTION EQUIPMENT IS USED WHERE APPROPRIATE.
FUME EXTRACTION EQUIPMENT MUST BE IN OPERATION WHEN SOLVENTS ARE USED E.G. TRICHLOROETHANE,
WHITE SPIRIT, SBP3, METHYLENE CHLORIDE, PERCHLORETHY LENE. DO NOT SMOKE IN THE VICINITY OF VOLATILE
DEGREASING AGENTS.
General workshop practices:
Disc
onnect the grounded termin
al of the vehicle battery.
D
o not apply heat in an attempt to free seized nuts or fitt
ings; as well as causing damage to protective coatings,
there is a risk of damage from stray heat to electronic equipment and brake lines.
Keep oils and solven
ts away from naked flames and other sour
ces of ignition.
Adhere str
ictly to handling and safety inst
ructions given on containers and labels.
E
nsure that a suitab
le form of fire extinguisher is conveniently located.
Wh
en using electrical tools and equipment, inspect the power
lead for damage and check that it is properly earthed.
D
o not leave tools, equipment, spilt oil etc. around the work area.
Working beneath a vehicle:
Wh
enever possible, use a ramp or
pit in preference to jacking.
Posit
ion chocks at the wheels as we
ll as applying the parking brake.
N
ever rely on a jack alone to support a
vehicle; use axle stands, or blocks care fully placed at the jacking points, to
provide a rigid location.
Ch
eck that any lifting equipment used has adeq
uate capacity and is fully serviceable.
Working on air conditioning systems:
D
o not disconnect any pipes of the refrigeration system
unless you are trained and instructed to do so; a refrigerant
is used which can cause blindness if allowed to come into contact with the eyes.
Health Protection

P

rolonged and repeated contact with mineral oil will result in the removal of natural oils from the skin, leading to dryness,


In
spection

irri
tation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin
cancer. Washing facilities and adequate means of skin protection should be provided.
Observe these recommendations:
Wear pro t
ective clothing and impe
rvious gloves when necessary.
Do not put oily
rags in pockets. Avoid contaminat
ing clothes, particularly underwear, with oil.
Overal
ls must be cleaned re
gularly; discard oil impregna ted clothing and footwear wh ich cannot be washed or
cleaned.
Fi rst
Aid treatment should be obtained
immediately for open cuts or wounds.
Use barrier
creams, applying before each work period, to en
able easier removal of dirty oil and grease from the skin.
Wa
sh with soap and water to ensure th
at all oil is removed (skin cleaner and a nail brush will help). The use of
preparations containing lanolin will help to replace the natural skin oils which have been removed.
Do
not use petrol, kerosene, gas oil, th
inners or solvents for washing skin.
If
skin disorders develop, obtain medical advice immediately.
Wh
ere prac
ticable, degrease components prior to handling.
W
h
ere there is a risk of fluids coming into contact with th
e eyes, suitable eye protection should be worn - goggles or
face shield. An eye wash facility should be provided.
Ensure that a
dequate ventilation is provided when volatile degreasing agents are being used.
E
n
vironmental Protection
In so
m
e countries it is illegal to pour used oil onto the ground
, down sewers or drains, or into water courses. The burning of
used engine oil in small space heaters or boilers is not reco mmended unless emission control equipment is fitted. Dispose of
used oil through authorized waste disposal contractors, to licensed waste disposal sites or to the waste oil reclamation
trade. If in doubt, contact the Local Authority for advice on disposal facilities.
On-Board Diagnostics (OBD)
Ve
hicles use programmed electronic control systems to prov
ide engine management and emission regulation, automatic
transmission operation and anti -lock braking control. These control systems ha ve an integral On-Board Diagnostics (OBD)
facility for use in conjunction with either Jaguar diagnostic equipment or a scan t ool which is capable of retrieving DTCs,
PIDs and performing active commands.
The OBD information in this manual provid es diagnostic and rectification procedures for emission related electrical and
mechanical systems. The informat ion is intended to facilitate fault diagnosis and the subsequent rectification of vehicles
without recourse to the portab le diagnostic unit (PDU).
OBD related information can be fo und in the following sections:
General Information

Engine M

anagement System
Auto

matic Transmission
Anti-lock Br

aking System
Where appropriate a section comprises the following sub-sections:
Description and Operation
A ge
neral illustration and parts list to help the identi
fication of the particular system or component.
A b
rief description of the system operating characteristics and monitoring procedure
accompanied by a component
illustration.
Addi ti
onal information, where appropriat
e, is provided in the form of component calibrations, characteristics and
cross sectional views.
A localized circui
t diagram is included to provide circuit iden
tification and details of connectors, splices, fuses, wire
gauge and colors. See Circuit Diagrams.
Diagnosis and Testing (dedicated to fault analysis and rectification)
Recommended special tools. Symptom chart; a ch
art contai
ning all relevant Diagnostic Trouble Code s (DTC), their possible causes and an
indication of the appropriate test.
Sp
ecific pinpoint test(s), de
signed so that fault diagnosis can be carr ied out in a logical and efficient manner.

•
NOTE: For convenience, pinpoint test il
lustrations indicating voltage measurements do not always accurately reflect the
conventional method of connecting a multimeter. More explicitly, if the multimeter probes are connected as shown in some
illustrations (positive probe to ground), the voltage reading would be preceded by the negative sign '-', indicating that the
probes have been connected in the reverse manner to the norm al convention. The accuracy of the reading is not affected
and the '-' sign can be ignored when comparing the reading with the results indicated in the text of the pinpoint test.
Removal and Installation
Re
moval procedure(s), formatted
in the recommended sequence
Il
lustrated guide to the use of special tools
Il

lustrations to support the relevant text
Installation

procedure as above and including special re
commendations for processes, lubricants and tightening
torques.
Cir
cuit Diagrams
To
understand the relationship between the vehicle electric
al system and the system circuit diagrams, refer to the
appropriate Electrical Guide.
Fault Identificatio
n (DTC)
The diagnostic trouble codes (DTCs) are
li
sted in Section 303-00 under Diagno
stic Trouble Codes and include, where
applicable, the corresponding manual section reference.

General Information - Terminology Glossary

Description an
d Operation

This glossary of terms is intended to cover emissions-related (to SAE J 1930) term inology, and other abbreviations that may
be used in this manual.
The required term may be looked-up in th e left-hand column, and subsequent columns give the standard acronym, unit or
abbreviation, and definition.
Te rm
(s)
Acr
ony
m /
Unit /
Abbreviation
De fi
nition
A
Accel
e
rator Pedal
AP
Af
ter Botto
m Dead
Center
ABDCEvent occurri ng after
BDC
Af
ter Top Dead CenterATDCEvent occurri ng after
TDC
Ai
rbag /
Supplementary
Restraint System
Airbag, SRSAi rbag restraint system for
dr
iver and front seat passenger
Air Cleane rACL
Air ConditioningA/C
Air Conditioning Con t
rol
Module
A/CCMModule c
ontrolling air conditioning, heating and ventilation
Air Conditioning SignalACSA
i
r conditioning compressor clutch operation is signalled to the ECM which
induces idle speed corrections to co mpensate for engine load changes
Alternating cu
rrent
ac
Ai
r Fuel R
atio
AFRN
omi
nally 14.7 parts air to one part fuel
Ampe
reASI unit of current
Ampere hourAhA current of one ampere
fl
owing for one hour
Anti-Lock Braking SystemABSS
y
stem which prevents wheel lock-up
under braking by sensing lack of
rotation of a wheel(s) and divertin g fluid pressure away from it (them)
ABS Control Mo
dule
ABS CM
ABS /
T
raction Control
Control Module
ABS / T
C CM
Atmosph
e
re
atmU
n
it of pressure (1.01325 bar)
Au
to
matic Stability
Control
ASCA form of vehicle
control
in which the ECM reduces en gine torque to control
wheel-spin
B
Baro me
tric Absolute
Pressure Sensor
BAR OSensor measuring the pressure of surr ou
nding air at any given temperature
and altitude
Bat t
ery positive voltage
B+The posi
ti
ve voltage from a battery or
any circuit connected directly to it
Before Bottom Dead
CenterBBDCEvent occurri ng before BD
C
Before Top Dead

Center
BTD
CEvent (usual ly
ignition) occurring before TDC
Blowe
rBLRDe
vice which supplies a current of air at
moderate pressure, e.g. heater or
A/C blower
Body Processor M
odule
BPMControl modu
le
for body electrical systems, e.g. interior lamps, windshield
wash / wipe control
Bott om D
ead Center
BD
CLowest poin t of piston
travel in a reciprocating engine
Brake hors
epowe
r
bhpEffecti
ve horsepower devel
oped by an
engine or motor, as measured by a
brake applied to its output shaft
Brake Mean Effective
Pres sureBME PThat p
art of the effective
pressure developed in a cyli nder that would result in
a cylinder output equal to the bhp of the engine
Brake On/ O
ff
BOOIn
dic
ates the position of the brake pedal
Br
it
ish Standard
BSStan
dar
d specification issued by the British Standards Institution
Br
it
ish Standard
Automotive
BSAu
BusTopology of a commu n
ication network
Bypass
AirBPAMechanica l
control of throttle bypass air
C
Camshaft Posit
i
on Sensor
CMPSIndi
cat
es camshaft position
Canadian Motor
V
ehicle
CMVSS

Safety Standard
Canister PurgeCANPControls pu
rging of the EVAP canister
Carbon dioxideCO2Colorless gas with

a density of a
pproximately 1.5 ti mes that of air
Carbon mon
oxide
COPoi
sonous gas produced as the re
sult of incomplete combustion
Case G
round
CSE GNDControl modu
le casing ground
Catal

ytic converter
In
-line exhaust system device used to reduce the level of engine exhaust
emissions
Ce
lsius
CSI ter
m for the Centigrade scale, with
freezing point at zero and boiling point
at 100°
Central
Processor Unit
CPUTh
e section of a computer that contai
ns the arithmetic, logic and control
circuits. It performs arithm etic operations, controls instruction processing, and
provides timing signals and other housekeeping operations
Cl
osed Loop
CL
Cl

osed Loop System
CLSControl
system with one
or more feedback loops
Col
umn/Mirror Control
Module
C/MC
M
Control ModuleCMA

self-contained group of electrical/electronic components, designed as a
single replaceable un it, and controlling one or more processes
Controll
er Area Network
CANA
communication system which allows control modules to be linked together
in a network.
Crankshaft Posi
tion
Sensor
CKPSGenerates crankshaft positi on informa
tion in conjunct
ion with the CKPTR (also
generates speed information in certain applications)
Crankshaft Posi
tion
Timing Ring
CKPT
R
Toothe
d ring which
triggers the CKPS
Crankcase Ventila
tion
System
CVSys
tem which scavenges camshaft cover and crankcase emissions and feeds
them into the inlet manifold
Cubic ce nt
imeter
cm
3
Curb weightWe

ight of vehicle with fuel, lubrican
ts and coolant, but excluding driver,
passengers or payload
D
Dat
a Link Connector
DLCConne
ctor providing access and/or control of the vehicle information,
operating conditions, and diagnostic information
De
gree
deg, °Angle or tempe
rature
D

epartment of
Transportation (US)
DO
T
D

epartment of Transport
(UK)
DTp
De
utsche In
stitut für
Normung
DINGerman stand
ards regulation body
Di

agnostic Module
DMSuppl
emental Restraint System (non-c
ontrolling) module for diagnostics
overview
Di
agnostic Test Mode
DTMA le
vel of capability in an OBD system.
May include different functional states
to observe signals, a base level to re ad DTCs, a monitor level which includes
information on signal levels, bi-directional control with on /off board aids, and
the ability to interface with remote diagnosis
Diagnostic Trouble CodeDTCAn al
pha/numeric identifier for a fault
condition identified by the On-Board
Diagnostic (OBD) system
D
ial test indicator
DTIA mechan
ical measuring
instrument, with a rotary indicating pointer
connected to a linear operating probe
D
ifferential pressure
Pressure di
fference betwee
n two regions e.g. between intake manifold and
atmospheric pressures
D
ifferential Pressure
Feedback EGR
DP
FE
An
EGR system that monito
rs differential EGR pressure across a remote orifice
to control EGR flow
D
irect current
dcCurrent which f
lows in on
e direction only, though it may have appreciable
pulsations in its magnitude
Du
al linear switch
DLSJ
-gate switch connected to the TCM on SC vehicles
E
EGR

Temperature EGRT
Sensor
EGRTSens
ing EGR function based on temperature change
EGR Vacu

um Regulator
EVRControls EGR
flow by changi
ng vacuum to the EGR valve
EGR Valve
Position
EVPAn EGR
system that direct
ly monitors EGR valve position to control EGR flow
Electrically E
rasable
Programmable Read-Only
Memory
EEP
ROM