JAGUAR XFR 2010 1.G Workshop Manual
Page 1021 of 3039
2. NOTE: Lubricate and install the new O-ring seals.
Torque:
M8 25 Nm M6 12 Nm
3. NOTE: Lubricate and install the new O-ring seals.
4. Torque: 12 Nm www.JagDocs.com
Page 1022 of 3039
6. NOTE: Tsubaki timing drive only.
Install the lower timing chain making sure the coloured
chain links align correctly with the fuel rail high-pressure
fuel pumps camshaft and crankshaft sprocket markings.
Page 1023 of 3039
7. CAUTION: Make sure that the tensioner spring is
correctly located.
NOTE: Tsubaki timing drive only.
Torque: 21 Nm
8. NOTE: INA timing drive only.
Install the lower timing chain making sure the coloured
chain links align correctly with the fuel rail high-pressure
fuel pumps camshaft and crankshaft sprocket markings.
Page 1024 of 3039
9. CAUTION: Make sure that the tensioner spring is
correctly located.
NOTE: INA timing drive only.
Torque: 21 Nm
10. Refer to: Oil Pan Extension (303-01C Engine - V8 5.0L Petrol, Removal and Installation).
11. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
Page 1025 of 3039
Engine - V8 S/C 5.0L Petrol - Timing Cover
Removal and Installation
Removal
NOTE: Removal steps in this procedure may contain installation details. Published: 12-Sep-2011
1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
2. WARNING: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.
3. Refer to: Accessory Drive Belt (303-05D Accessory Drive - V8 S/C 5.0L Petrol, Removal and Installation).
4. Refer to: Accessory Drive Belt Tensioner (303-05D Accessory Drive - V8 S/C 5.0L Petrol, Removal and Installation).
5. Refer to: Thermostat Housing - Vehicles With: Supercharger (303-03C Engine Cooling - V8 5.0L Petrol/V8 S/C 5.0L Petrol, Removal and
Installation).
6. Refer to: Valve Cover LH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
7. Refer to: Valve Cover RH (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
8. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
9. NOTE: Engine shown removed for clarity.
Page 1026 of 3039
10.
11.
12. NOTE: Engine shown removed for clarity.
NOTE: Engine shown removed for clarity.
NOTE: Engine shown removed for clarity. www.JagDocs.com
Page 1027 of 3039
Installation
Page 1028 of 3039
3. NOTE: Tighten the bolts in the indicated sequence.
Torque: 12 Nm
4. NOTE: Tighten the bolts in the indicated sequence.
Torque: 12 Nm
Page 1029 of 3039
5. CAUTION: Make sure that the mating faces are clean
and free of foreign material.
Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G) to the
areas shown, and tighten the bolts within 7 minutes.
6. CAUTION: Make sure that the mating faces are clean
and free of foreign material.
Install the bolts, but do not tighten fully at this stage.
Page 1030 of 3039
7.
8.
9.
10. NOTE: Tighten the bolts in the indicated sequence.
Torque: 12 Nm
Torque: 12 Nm
Torque: 12 Nm
Torque: 12 Nm