Bolt JAGUAR XFR 2010 1.G Workshop Manual
Page 994 of 3039
5. CAUTIONS:
The bolts can only be used 3 times, mark the bolts with a center punch.
If 2 punch marks are visible, discard the bolts.
Make sure that no components fall off during removal.
NOTES:
Make sure that the crankshaft is not rotated.
Make sure the crankshaft and flexplate mating faces are clean before
installation.
6.
7.
8.
Page 1003 of 3039
Installation
1. Torque: 8 Nm 2. CAUTIONS:
Make sure that the mating faces are clean and free of foreign material.
Use only a plastic scraper when removing the sealing material.
Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G) to the areas
shown, and tighten the bolts within 7 minutes.
3. NOTE: Tighten the bolts in the indicated sequence.
Torque: 25 Nm
Page 1004 of 3039
4. CAUTIONS:
Make sure that the mating faces are clean and free of foreign material.
Use only a plastic scraper when removing the sealing material.
Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G) to the areas
shown, and tighten the bolts within 7 minutes.
5. NOTE: Tighten the bolts in the indicated sequence.
Torque: 12 Nm
6. CAUTION: Make sure that the mating faces are clean and free of foreign
material.
Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G) to the areas shown, and
tighten the bolts within 7 minutes.
Page 1005 of 3039
7. CAUTION: Make sure that the mating faces are clean and free of
foreign material.
NOTE: Install new lower timing cover.
Install the bolts, but do not tighten fully at this stage.
Special Tool(s): 303-1433
8. NOTE: Tighten the bolts in the indicated sequence.
Torque:
M6 12 Nm M8 20 Nm
9. Remove the special tool.
10. Torque: 12 Nm
Page 1006 of 3039
11.
12. Torque: 10 Nm
Special Tool(s): 303-1442, 303-1443
13. Remove the special tools.
14. NOTE: Tighten the bolts in the indicated sequence.
Torque: 11 Nm www.JagDocs.com
Page 1009 of 3039
23.
24.
25. Loosen the Torx screws half a turn each.
CAUTIONS:
Install new high-pressure fuel supply lines.
Lubricate only the union threads with clean engine oil.
NOTES:
Remove and discard the blanking caps.
Install the bolt and unions fully finger tight before final tightening.
Page 1012 of 3039
31.
32.
33. NOTES:
Install the bolt and unions finger tight before final tightening.
Remove and discard the blanking caps.
Torque:
Unions 21 Nm M6 11 Nm
Torque:
Unions 21 Nm
Torque:
M10 29 Nm M6 11 Nm
Page 1016 of 3039
45.
46.
47.
48. Torque: 12 Nm
CAUTION: Install all the bolts finger tight before final tightening.
Torque: 25 Nm
CAUTION: Install all the bolts finger tight before final tightening.
NOTE: Tighten the bolts in the indicated sequence.
Torque: 48 Nm www.JagDocs.com
Page 1017 of 3039
49. CAUTIONS:
Install all the bolts finger tight before final tightening.
The bolts can only be used 3 times, mark the bolts with a center punch.
If 2 punch marks are visible, discard the bolts.
Install the bolts in the noted position.
NOTES:
Make sure that the crankshaft is not rotated.
Make sure the crankshaft and flexplate mating faces are clean before
installation.
Tighten the retaining bolts working diagonally.
Torque:
Stage 1:45 Nm Stage 2:90°
50. Refer to: Engine (303-01D Engine - V8 S/C 5.0L Petrol, Installation).
51. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).
52. Lower the vehicle.
53. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).
Page 1028 of 3039
3. NOTE: Tighten the bolts in the indicated sequence.
Torque: 12 Nm
4. NOTE: Tighten the bolts in the indicated sequence.
Torque: 12 Nm