Bolt JAGUAR XFR 2010 1.G Workshop Manual

5. CAUTION: Make sure that the mating faces are clean
and free of foreign material.

Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G) to the
areas shown, and tighten the bolts within 7 minutes.




















6. CAUTION: Make sure that the mating faces are clean
and free of foreign material.

Install the bolts, but do not tighten fully at this stage.

7.
















8.
9.
10. NOTE: Tighten the bolts in the indicated sequence.

Torque: 12 Nm













Torque: 12 Nm
















Torque: 12 Nm
















Torque: 12 Nm

22.























23. CAUTION: Make sure that the torque wrench does not
move whilst tightening the VVT bolts.


NOTE: Make sure to tighten the exhaust VVT unit
bolts first.
Torque: 32 Nm Special Tool(s): 303-1482
















Install the oil suction tube.
Torque: 10 Nm

26. CAUTION: Make sure that the torque wrench does not
move whilst tightening the VVT bolts.

first. NOTE: Make sure to tighten the inlet VVT unit bolts
Torque: 32 Nm












27.
28.
Remove the special tool.

























Remove the special tool.

29.
30.
31.
Remove the special tool.
Special Tool(s): 303-1447















Install the special tool.
Special Tool(s): 303-1448
















CAUTION: Install the crankshaft pulley bolt with an
M16 washer to prevent damage to the crankshaft on
installation.
Torque: 50 Nm

36.
37.
38.


























Remove the special tool.
Special Tool(s): 303-1448














CAUTIONS:


If the special tool cannot be installed, return to step
22 of the installation until the special tool 303-1445 is
installed correctly.


If directed to step 22, make sure that the VVT unit
retaining bolts are loosened prior to installing the special
tool(s).
Install the special tool.

Special Tool(s): 303-1445

3. NOTE: Tighten the bolts in the indicated sequence.
Torque: 13 Nm

3. NOTE: Tighten the bolts in the indicated sequence.

Torque: 13 Nm

3. NOTE: Tighten the bolts in the indicated sequence.

Torque:
M6 12 Nm M8 20 Nm











4. Torque: 12 Nm













5. Refer to: Brake Vacuum Pump - V8 5.0L Petrol/V8 S/C 5.0L Petrol (206-07 Power Brake Actuation, Removal and Installation).

6. Torque: 25 Nm

7. NOTE: Install the bolt finger tight before final
tightening.
Torque: 40 Nm












8. Torque: 40 Nm













9. Refer to: Crankshaft Pulley (303-01D Engine - V8 S/C 5.0L Petrol, Removal and Installation).

10. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


11. CAUTION: Make sure that the vehicle is left for 5 minutes from
filling with oil and that the engine oil level is reading at least minimum
(by following Steps 14-18), before starting the engine.

Fill the engine with oil - for filling values on vehicles without
supercharger:

Refer to: Specifications (303-01C Engine - V8 5.0L Petrol, Specifications).
Fill the engine with oil - for filling values on vehicles with
supercharger:

Refer to: Specifications (303-01D Engine - V8 S/C 5.0L Petrol, Specifications).
Clean any residual engine oil from the oil filler cap area.


12. CAUTION: Make sure that the vehicle has been left for 5 minutes
from filling with oil.
Follow the Steps 14-18 before starting the engine.

13.
Start the engine and allow to run for 10 minutes, stop the
engine.