Bolt JAGUAR XFR 2010 1.G Workshop Manual

13.
















14.
15. NOTE: LH shown RH similar.

Torque: 7 Nm















NOTE: LH shown RH similar.

















CAUTION: Lubricate only the union threads with clean engine oil.

NOTES:


Engine shown removed for clarity.


Install the bolt and unions finger tight before final tightening.


Remove and discard the blanking caps.
















16. Lower the vehicle. www.JagDocs.com

24.


















25.


















NOTES:


Lubricate the
union threads
with clean
engine oil.


Do not
tighten at
this stage.


Remove
and discard
the blanking
caps.





26. Torque:
Unions 21 Nm Bolts 8 Nm

5. CAUTION: Install new high-pressure fuel supply lines.
NOTES:
Engine shown removed for clarity.

Remove and discard the blanking caps.

Install the bolt and unions fully finger tight before final
tightening.























6. CAUTION: Care must be taken when positioning the fuel rail
high-pressure fuel pump cover to one side.

NOTE: Fuel rail high-pressure fuel pump cover shown removed for
clarity.
Torque: 12 Nm





7. Lower the vehicle.
8. NOTES:

Do not tighten at this stage.

Remove and discard the blanking caps.








9. WARNING: Do not work on or under a vehicle supported only by a jack. Always

12.
13.
14. NOTES:

Install the bolt and unions finger tight before final tightening.

Remove and discard the blanking caps.
Torque: Unions 21 Nm M6 11 Nm














Torque: 21 Nm


















NOTE: Engine shown removed for clarity.
Torque: M10 29 Nm M6 11 Nm

21. NOTES:

Lubricate
the
union
threads
with
clean
engine
oil.

Do
not tighten
at this
stage.

Remove
and
discard
the
blanking
caps.

22. Torque: Unions 21 Nm Bolts 8 Nm










23. Refer to: Air Cleaner Outlet Pipe RH (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).
24. www.JagDocs.com

5. CAUTION: Install new high-pressure fuel supply lines.
NOTES:
Engine shown removed for clarity.

Remove and discard the blanking caps.

Install the bolt and unions fully finger tight before final
tightening.






















6. CAUTION: Care must be taken when positioning the fuel rail
high-pressure fuel pump cover to one side.

NOTE: Fuel rail high-pressure fuel pump cover shown removed for
clarity.
Torque: 12 Nm





7. Lower the vehicle.
8. NOTES:

Do not tighten at this stage.

Remove and discard the blanking caps.








9. WARNING: Do not work on or under a vehicle supported only by a jack. Always
support the vehicle on safety stands.

12.
13.
14. NOTES:

Install the bolt and unions finger tight before final tightening.

Remove and discard the blanking caps.
Torque: Unions 21 Nm M6 11 Nm














Torque: 21 Nm


















NOTE: Engine shown removed for clarity.
Torque: M10 29 Nm M6 11 Nm

Bolts 8 Nm










25. Refer to: Air Cleaner Outlet Pipe RH (303-12D Intake Air Distribution and Filtering - V8 S/C 5.0L Petrol, Removal and Installation).

26.
27. 28.













29. Refer to: Engine Cover - V8 5.0L Petrol/V8 S/C 5.0L Petrol (501-05 Interior Trim and

Accessory drive belt tensioner retaining bolt 40 30 - Accessory drive belt idler pulley retaining bolt - all vehicles 40 30 - Accessory drive belt center idler pulley retaining bolt - vehicles without supercharger 25 19 - Accessory drive belt idler pulley retaining bolt to tensioner bracket - vehicles with supercharger 40 30 - Supercharger belt tensioner bracket retaining bolt 25 19 - Supercharger belt tensioner retaining bolt 40 30 - Supercharger belt 76mm idler pulley retaining bolt 40 30 - Supercharger belt 90mm idler pulley retaining bolt 56 41 -

Starter motor retaining bolts 47 35 - Battery positive terminal connector retaining nut 10 7 - Solenoid terminal connector retaining nut 7 - 62 www.JagDocs.com