Bolt JAGUAR XFR 2010 1.G Workshop Manual

9.
10.

11.
12.
























































CAUTION: Discard the bolts.

NOTES:


Discard the gasket.


Make sure that the position of the spacers is noted
before removal of the manifold. www.JagDocs.com

3. NOTE: If a new cylinder head is installed use the
special tools in the illustration.
Special Tool(s): 303-1444-02












4. CAUTION: Make sure that new bolts are installed.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm










5. Remove the special tool.
6. CAUTION: Make sure that new bolts are installed.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm

7.

8.

9.
10. Torque: 18 Nm



































Torque: 100 Nm

















WARNING: Make sure that a new bolt is installed.


NOTE: Some variation in the illustrations may occur,
but the essential information is always correct.
Torque: 35 Nm

5.
6.
All vehicles

7.
CAUTION: Discard the bolt.

Torque: 35 Nm













Torque: 100 Nm



















Torque: 12 Nm

8.

9.

10.
11. Torque: 48 Nm





















































CAUTIONS:


Discard the bolts.


LH illustration shown, RH is similar.
NOTES:


Discard the gasket.


Make sure that the position of the spacers is noted
before removal of the manifold.

3. CAUTION: LH illustration shown, RH is similar.


NOTE: If a new cylinder head is installed use the
special tools in the illustration.
Install the special tool.

Special Tool(s): 303-1444-02







4. CAUTIONS:


Make sure that new bolts are installed.
LH illustration shown, RH is similar.
NOTE: Install the spacers in the noted position.

Torque: 10 Nm





5. CAUTION: LH illustration shown, RH is similar.
Remove the special tool.














6. CAUTIONS:


Make sure that new bolts are installed.
LH illustration shown, RH is similar.
NOTE: Install the spacers in the noted position.
Torque: 10 Nm www.JagDocs.com

11. Torque: 48 Nm













Right-hand drive vehicles

12.
13.
CAUTION: Discard the bolt.

Torque: 35 Nm













Torque: 100 Nm

Engine - V8 S/C 5.0L Petrol - Flexplate
Removal and Installation

Removal


NOTE: Removal steps in this procedure may contain installation details. Published: 11-May-2011

1. Refer to: Battery Disconnect and Connect (414-01 Battery, Mounting and Cables, General Procedures).


2. CAUTION: Make sure to support the vehicle with axle stands.
Raise and support the vehicle.

3. Refer to: Transmission - V8 5.0L Petrol/V8 S/C 5.0L Petrol (307-01B Automatic Transmission/Transaxle - TDV6 3.0L Diesel /V8 5.0L Petrol/V8
S/C 5.0L Petrol, Removal).

4. CAUTIONS:


Install all the bolts finger tight before final tightening.


The bolts can only be used 3 times, mark the bolts
with a center punch. If 2 punch marks are visible, discard
the bolts.
Make sure that no components fall off during removal.
Install the bolts in the noted position.

NOTES:


Make sure the crankshaft and flexplate mating faces
are clean before installation.


Make sure that the crankshaft is not rotated.


Tighten the retaining bolts working diagonally.
Torque:
Stage 1:45 Nm Stage 2:90°
Installation

1. To install, reverse the removal procedure.

Installation 9. CAUTIONS:


Make sure that these components are installed to the
noted removal position.


Install new o-ring seals

1. CAUTIONS:


Install all the bolts finger tight before final tightening.


Make sure that the area around the component is
clean and free of foreign material.


Install the new seals.


NOTE: Tighten the bolts in the indicated sequence.
To install, reverse the removal procedure.

Installation
1. CAUTIONS:


Use only a plastic scraper when removing the sealing
material.


Use lint free cloth.


Make sure that the mating faces are clean and free of
corrosion and foreign material.

Apply RTV sealant WSE-M4G323-A6 (Loctite 5901G)
to the areas shown, and tighten the bolts within 7
minutes.
Apply a bead of sealant, 2.5 mm diameter, to the
area indicated.








2. NOTE: Tighten the bolts in the sequence shown.
Torque: 12 Nm
















3. Refer to: Engine Oil Level Sensor (303-14D Electronic Engine Controls - V8 S/C 5.0L Petrol, Removal and Installation).